BS 5072-2-1974 Methods of test for sodium fluoride for industrial use - Determination of moisture content《工业用氟化钠试验方法 第2部分 水含量测定》.pdf

《BS 5072-2-1974 Methods of test for sodium fluoride for industrial use - Determination of moisture content《工业用氟化钠试验方法 第2部分 水含量测定》.pdf》由会员分享，可在线阅读，更多相关《BS 5072-2-1974 Methods of test for sodium fluoride for industrial use - Determination of moisture content《工业用氟化钠试验方法 第2部分 水含量测定》.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS 5072-2: 1974 Incorporating Amendment No. 1 Methods of test for Sodium fluoride for industrial use Part 2: Determination of moisture content UDC 661.833.361:546.33131:543.712BS5072-2:1974 This British Standard, having been approved by the ChemicalsIndustry StandardsCommittee, wasp

2、ublished under theauthorityofthe ExecutiveBoardon 31July1974 BSI 11-1999 The following BSI references relate to the work on this standard: Committee reference CIC/24 Draft for comment 72/52985 DC ISBN 0 580 08432 9 Co-operating organizations The Chemicals Industry Standards Committee, under whose su

3、pervision this British Standard was prepared, consists of representatives from the following Government departments and scientific and industrial organizations: British Steel Industry Chemical Industries Association* Department of Health and Social Security Department of Trade and Industry* Departme

4、nt of Trade and Industry Laboratory of the Government Chemist* Fertiliser Manufacturers Association Limited Ministry of Agriculture, Fisheries and Food National Sulphuric Acid Association Royal Institute of Public Health and Hygiene Soap and Detergent Industry Association The organizations marked wi

5、th an asterisk in the above list, together with the following, were directly represented on the committee entrusted with the preparation of this British Standard: Aluminium Federation British Ceramic Research Association Royal Institute of Chemistry Society for Analytical Chemistry Society of Chemic

6、al Industry Amendments issued since publication Amd. No. Date of issue Comments 5347 March 1987 Indicated by a sideline in the marginBS5072-2:1974 BSI 11-1999 i Contents Page Co-operating organizations Inside front cover Foreword ii 1 Scope 1 2 Principle 1 3 Apparatus 1 4 Procedure 1 5 Expression of

7、 results 1 Publications referred to Inside back coverBS5072-2:1974 ii BSI 11-1999 Foreword This British Standard has been prepared under the authority of the Chemicals Industry Standards Committee in order to provide methods for the analysis of sodium fluoride. In the drafting of this standard, acco

8、unt has been taken of the method adopted by the International Organization for Standardization (ISO), in the preparation of which the UnitedKingdom has been an active participant. It is intended to provide further methods, in the form of parts of this standard, as the work of ISO/TC47 and, in partic

9、ular, ISO/TC47/SC7 Alumina and related compounds, advances. This Part is based on International Standard ISO2832, “Sodium fluoride for industrial use. Determination of moisture content”, modified to take into account the comments made by the UnitedKingdom during its development. This standard prescr

10、ibes methods of test only, and should not be used or quoted as a specification defining limits of purity. Reference to the standard should be in a form of words indicating that the methods of test used conform to BS5072-2. A British Standard does not purport to include all the necessary provisions o

11、f a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pagesi andii, pages1 and 2, an inside b

12、ack cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover.BS5072-2:1974 BSI 11-1999 1 1 Scope This Part of this British Standard specifies a gravimetric method for

13、the determination of the moisture content of sodium fluoride for industrial use. NOTEThe title of the British Standard referred to in this standard is given on the inside back cover. 2 Principle A test portion is dried for2h at110 C and the loss of mass is determined. 3 Apparatus Ordinary laboratory

14、 apparatus and the following items are required. 3.1 Weighing bottle. This shall be shallow and approximately45mm in diameter. 3.2 Electric oven. Ventilated by convection and capable of being controlled at110 2 C (seeBS2648). 4 Procedure 4.1 Test portion. Dry the weighing bottle (see3.1) to constant

15、 mass in the oven (see3.2), controlled at110 2 C transfer it to a desiccator and after cooling to ambient temperature, weigh to the nearest0.001g. Then weigh, to the nearest0.001g, into the tared weighing bottle, approximately20g of the crude test sample 1) . 4.2 Determination. Place the uncovered w

16、eighing bottle, together with its lid, in the oven (see3.2), controlled at110 2 C, and maintain at this temperature for2h. Remove the weighing bottle and its lid from the oven and place them in a desiccator, without closing the weighing bottle completely. After cooling to ambient temperature close t

17、he weighing bottle with its lid and weigh to the nearest0.001g. Repeat the operations of heating, cooling and weighing until the difference between two successive weighings does not exceed2mg. 5 Expression of results The moisture content is given, as a percentage by mass, by the formula: where 1) Se

18、e BS 5072-4. m 0 is the mass of the weighing bottle, and its lid(g); m 1 is the mass of the weighing bottle, its lid and the test portion before drying (g); m 2 is the mass of the weighing bottle, its lid and the test portion after drying (g).2 blankBS5072-2:1974 BSI 11-1999 Publications referred to

19、 This standard makes reference to the following British Standards: BS 2648, Performance requirements for electrically-heated laboratory drying ovens. BS 5072, Methods of test for sodium fluoride for industrial use. BS 5072-4, Preparation and storage of samples. BS 5072-2: 1974 BSI 389 Chiswick High

20、Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment o

21、r revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would info

22、rm the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards

23、. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published a

24、s BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which gi

25、ve details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits cont

26、act Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no ex

27、tract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as s

28、ymbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.