ASTM F2745-2011 Standard Specification for Required Product Information to be Provided with an Airplane《飞机配备的必要产品信息的标准规格》.pdf

《ASTM F2745-2011 Standard Specification for Required Product Information to be Provided with an Airplane《飞机配备的必要产品信息的标准规格》.pdf》由会员分享，可在线阅读，更多相关《ASTM F2745-2011 Standard Specification for Required Product Information to be Provided with an Airplane《飞机配备的必要产品信息的标准规格》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: F2745 11Standard Specification forRequired Product Information to be Provided with anAirplane1This standard is issued under the fixed designation F2745; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last

2、revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 The following requirements apply to the documentationof Light Sport Airplanes. This specification covers the PilotsOperatin

3、g Handbook (POH), Flight Training Supplement(FTS), Maintenance Manual, Aircraft Kit Assembly Instruc-tions (KAI), Component Original Equipment Manufacturer(OEM) manuals, Aircraft OEMs Statement of Compliance,Registration, and Airframe Records information required foraircraft designed and manufacture

4、d in accordance with theASTM Standards.1.1.1 This specification covers the minimum requirementsfor information that shall be provided by the airplane OEM orseller of a new light sport airplane, light sport airplane kit,engines, propellers, or accessories (that is, radio, transponder,instruments, GPS

5、, etc.) as a part of the initial sale or transfer tothe first end-user.1.1.2 This specification does not apply to the sale or transferof used light sport airplane, engines, propellers, or accessories.1.2 This specification applies to airplanes seeking civilaviation authority approval, in the form of

6、 airworthinesscertificates or other like documentation.1.3 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility

7、 of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2F2245 Specification for Design and Performance of a LightSport AirplaneF2483 Practice for Maintenance and the Development ofMaintenance Manuals for Light Sport AircraftF2563 Practice for Kit Assembly Instructions of A

8、ircraftIntended Primarily for Recreation3. Terminology3.1 Definitions:3.1.1 recordsrecords of maintenance, alterations, and in-spections for each aircraft subsequent to issuance of themanufacturers statement of compliance.3.2 Acronyms:3.2.1 FTSflight training supplement3.2.2 KAIkit assembly instruct

9、ions3.2.3 LSAlight sport aircraft (airplane)3.2.4 OEMoriginal equipment manufacturer3.2.5 POHpilots operating handbook4. Significance and Use4.1 The purpose of this specification is to provide theminimum information necessary for the proper identification,operation, and maintenance of each light spo

10、rt airplane.4.2 This specification does not define the method for docu-mentation delivery to the first end-user. Whether to providepaper, PDF, electronic records, access to the information on awebsite, or some combination shall be determined by theaircraft OEM.5. Minimum Information Requirements5.1

11、The following information shall be furnished by themanufacturer or seller at the time of sale of each airplane orairplane kit to the first end-user.5.1.1 The information plate specified in Section 6.5.1.2 The placards specified in Section 7.5.1.3 The Pilots Operating Handbook (POH) specified inSecti

12、on 8.5.1.4 The maintenance manual specified in Section 9.5.1.5 The component OEMs manuals specified in Section10.5.1.6 The aircraft OEMs statement of compliance specifiedin Section 11.5.1.7 The aircraft OEMs product/component registrationinformation specified in Section 12.5.1.8 The aircraft records

13、 specified in Section 13.5.2 The following information shall be furnished, as appli-cable, by the manufacturer or seller at the time of sale of eachairplane or airplane kit to the first end-user.1This specification is under the jurisdiction of ASTM Committee F37 on LightSport Aircraft and is the dir

14、ect responsibility of Subcommittee F37.20 on Airplane.Current edition approved June 1, 2011. Published September 2011. DOI:10.1520/F2745-11.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volum

15、e information, refer to the standards Document Summary page onthe ASTM website.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.5.2.1 The aircraft Flight Training Supplement (FTS) speci-fied in Section 14.5.3 The following information

16、 shall be furnished by themanufacturer or seller at the time of sale of each airplane kit tothe first end-user.5.3.1 The Airplane Kit Assembly Instruction (KAI) speci-fied in Section 15.6. Information Plate6.1 GeneralA manufacturer-issued fire proof informationplate, printed in English or as defined

17、 by the governing civilaviation authority or agency in which the aircraft was initiallysold, shall be permanently affixed to the aircraft in a visiblelocation and shall be designed to remain legible for theexpected life of the aircraft.6.2 MaterialThe information plate shall be made fromstainless st

18、eel, not less than 0.46 mm (0.018 in.) thick; mildsteel (corrosion-protected), not less than 0.46 mm (0.018 in.)thick; or alternative materials that provide equivalent protec-tion.6.3 InformationThe information plate shall contain thefollowing information.6.3.1 Serial NumberA unique identifying numb

19、er or codeissued by the aircraft manufacturer.6.3.2 Name of Aircraft OEMThe name of the aircraftOEM and country.6.3.3 ModelA unique identifying name, number, or codeassigned to each manufactured type of aircraft having the samebasic configuration or components and issued by the aircraftOEM.7. Placar

20、ds7.1 The following placards are required, must be displayedin a conspicuous place, and may not be easily erased, defaced,removed, or obscured.7.1.1 Passenger Warning: “This aircraft was manufacturedin accordance with Light SportAircraft airworthiness standardsand does not conform to standard catego

21、ry airworthinessrequirements.”7.1.2 “NO INTENTIONAL SPINS,” if applicable.8. Pilots Operating Handbook (POH)8.1 Each airplane shall have a hard-copy of the PilotsOperating Handbook (POH) provided that complies withSpecification F2245.9. Maintenance Manual9.1 Each airplane shall have a maintenance ma

22、nual pro-vided that complies with Specification F2483.10. Component Original Equipment Manufacturers(OEM) Manuals10.1 If the aircraft OEM has not incorporated the followinginformation into their aircraft manuals, the following compo-nent OEM documentation shall be provided to the first end-user.10.1

23、.1 Component OEM manuals for the engine, propeller,and accessories sold with the aircraft.10.1.1.1 For this standard, accessories are defined as anyassembly, subassembly, or component that requires some typeof pilot/owner maintenance or operation.10.1.2 Component OEM manuals may remain in the style,

24、format, arrangement, and medium (paper, PDF, etc.) providedby the component OEM. They may cover such topics as: setup,installation, adjustment, operation, repair, overhaul, other au-thorized maintenance, and parts ordering.11. Aircraft OEMs Statement of Compliance11.1 Each aircraft shall include a s

25、tatement identifying theASTM or other applicable standards used in designing andmanufacturing the product.Acopy of the statement provided tothe Civil Aviation Authority is acceptable.12. Product Registration Information12.1 The aircraft OEM shall provide any product registra-tion requirements for it

26、ems not already registered by theaircraft OEM. The information transferred should define howthe first end-user registers a component OEM product such asthe engine, propeller, primary flight displays, autopilot, GPS,and navigational radios.13. Aircraft Records13.1 The aircraft OEM shall provide all a

27、ircraft records.NOTE 1Requirements for aircraft records are typically dictated by acombination of ASTM standards requirements and applicable CivilAviation Authority (CAA) requirements. This generally includes suchthings as airframe logs, engine logs, airworthiness certificates, operatinglimitations,

28、 etc.14. Aircraft Flight Training Supplement (FTS)14.1 Any airplane with special flight training requirementsshall have a Flight Training Supplement (FTS) that complieswith Specification F2245.NOTE 2Some Civil Aviation Authorities (CAA) may require an FTS.15. Airplane Kit Assembly Instructions (KAI)

29、15.1 Each kit-built airplane shall have a Kit AssemblyInstructions (KAI) provided that complies with Practice F2563.16. Keywords16.1 flight training supplement; FTS; light sport aircraft;light sport airplane; maintenance manual; pilots operatinghandbook; POH; special airworthiness certificateF2745 1

30、12ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, a

31、re entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional stand

32、ardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Commi

33、ttee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).F2745 113