ASTM F2370-2015 Standard Test Method for Measuring the Evaporative Resistance of Clothing Using a Sweating Manikin《使用发汗人体模型测量服装耐蒸发性的标准试验方法》.pdf

《ASTM F2370-2015 Standard Test Method for Measuring the Evaporative Resistance of Clothing Using a Sweating Manikin《使用发汗人体模型测量服装耐蒸发性的标准试验方法》.pdf》由会员分享，可在线阅读，更多相关《ASTM F2370-2015 Standard Test Method for Measuring the Evaporative Resistance of Clothing Using a Sweating Manikin《使用发汗人体模型测量服装耐蒸发性的标准试验方法》.pdf（7页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: F2370 15Standard Test Method forMeasuring the Evaporative Resistance of Clothing Using aSweating Manikin1This standard is issued under the fixed designation F2370; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the ye

2、ar of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.INTRODUCTIONThe type of clothing worn by people directly affects the heat exchange between the human body andthe environment

3、. The heat transfer is both sensible (conduction, convection, and radiation) and latent(evaporation). The evaporative resistance of a clothing ensemble is dependent upon the designs andmaterials used in the component garments, the amount of body surface area covered by the clothing,the distribution

4、of the layers over the body, looseness or tightness of fit, and the increased surface areafor heat loss. Evaporative resistance measurements made on fabrics alone do not take these factors intoaccount. Measurements of the resistance to evaporative heat loss provided by clothing can be usedwith therm

5、al resistance values (Test Method F1291) to determine the comfort or stress of people indifferent environments.1. Scope1.1 This test method covers the determination of the evapo-rative resistance of clothing ensembles. It describes the mea-surement of the resistance to evaporative heat transfer from

6、 aheated sweating thermal manikin to a relatively calm environ-ment. Information on measuring the local evaporative resis-tance values for individual garments and ensembles is providedin Annex A1.1.1.1 This is a static test that provides a baseline clothingmeasurement on a standing manikin.1.1.2 The

7、 effects of body position and movement are notaddressed in this test method.1.2 The evaporative resistance values obtained apply only tothe particular ensembles evaluated and for the specified envi-ronmental conditions of each test, particularly with respect toair movement and sweating simulations.1

8、.3 Evaporative resistance values reported in SI units shallbe regarded as standard.1.4 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and

9、determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2E691 Practice for Conducting an Interlaboratory Study toDetermine the Precision of a Test MethodF1291 Test Method for Measuring the Thermal Insulation ofClothing Using a Heated Manikin2.2 I

10、SO Standards:3ISO 9920 Ergonomics of the Thermal EnvironmentEstimation of the Thermal Insulation and EvaporationResistance of a Clothing Ensemble3. Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 clothing area factor (fcl), nthe ratio of the surfacearea of the clothed body to the

11、 surface area of the nude body.3.1.2 clothing ensemble, na group of garments worntogether on the body at the same time.3.1.3 evaporative resistance, nthe resistance to evapora-tive heat transfer from the body to the environment.3.1.3.1 DiscussionThe evaporative resistance values canbe used to compar

12、e different clothing ensembles as long aseach test is conducted using the same experimental proceduresand test conditions. The following evaporative resistancevalues can be determined in this method:1This test method is under the jurisdiction ofASTM Committee F23 on PersonalProtective Clothing and E

13、quipment and is the direct responsibility of SubcommitteeF23.60 on Human Factors.Current edition approved Nov. 1, 2015. Published December 2015. Originallyapproved in 2005. Last previous edition approved in 2010 as F2370 - 10. DOI:10.1520/F2370-15.2For referenced ASTM standards, visit the ASTM websi

14、te, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Available from American National Standards Institute (ANSI), 25 W. 43rd St.,4th Floor, New York, NY 10036, http:

15、/www.ansi.org.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States1Rea= evaporative resistance of the air layer on the surfaceof the nude manikins sweating surface measuredunder isothermal conditions.Ret= total evaporative resistance of th

16、e clothing andsurface air layer around the manikin measured underisothermal conditions.Recl= intrinsic evaporative resistance of the clothing mea-sured under isothermal conditions.ARea= apparent evaporative resistance of the air layer onthe surface of the nude manikins sweating surfacemeasured under

17、 non-isothermal conditions.ARet= apparent total evaporative resistance of the clothingand surface air layer around the manikin measuredunder non-isothermal conditions.ARecl= apparent intrinsic evaporative resistance of the cloth-ing measured under non-isothermal conditions.3.1.4 total thermal resist

18、ance (Rt)the total resistance todry heat loss from the manikin that includes the resistanceprovided by the ensemble and the air layer around the clothedmanikin.4. Significance and Use4.1 This test method can be used to quantify and comparethe evaporative resistance provided by different clothing sys

19、-tems. The evaporative resistance values for ensembles mea-sured under isothermal conditions can be used in models thatpredict the physiological responses of people in differentenvironmental conditions. Garment evaporative resistance val-ues can be compared as well (see Annex A1).4.2 The measurement

20、 of the evaporative resistance providedby clothing is complex and dependent upon the apparatus andtechniques used. It is not practical in a test method of this scopeto establish details sufficient to cover all contingencies. Depar-tures from the instructions in this test method have the potentialto

21、lead to significantly different test results. Technical knowl-edge concerning the theory of heat transfer, moisture transfer,temperature, and air motion measurement, and testing practicesis needed to evaluate which departures from the instructionsgiven in this test method are significant. Standardiz

22、ation of themethod reduces, but does not eliminate, the need for suchtechnical knowledge. Report any departures with the results.5. Apparatus45.1 ManikinA standing manikin shall be used that isformed in the shape and size of an adult male or female andheated to a constant average surface temperature

23、.5.1.1 Size and ShapeThe manikin shall be constructed tosimulate the body of a human being; that is, it shall consist ofa head, chest/back, abdomen/buttocks, arms, hands (preferablywith fingers extended to allow gloves to be worn), legs, andfeet. Total surface area shall be 1.8 6 0.3 m2, and height

24、shallbe 170 6 10 cm. The manikins dimensions shall correspond tothose required for standard sizes of garments because devia-tions in fit will affect the results.5.1.2 Sweat GenerationThe manikin must have the abilityto evaporate water from its surface. Sweating system can be awater-fed capillary bod

25、y suit worn over a thermal manikin.Sweating can also be simulated by supplying water to andmaintaining it at the inner surface of a waterproof, butmoisture-permeable fabric skin. Other technologies exist thatdeliver water to the manikins surface with a valve deliverysystem.5.1.2.1 Sweating Surface A

26、reaThe entire surface of themanikin shall be heated and sweating including the head, chest,back, abdomen, buttocks, arms, hands, legs, and feet.5.1.3 Surface TemperatureThe manikin shall be con-structed so as to maintain a uniform temperature distributionover the nude body surface, with no local hot

27、 or cold spots. Themean surface (skin) temperature of the manikin shall be 35C.Local deviations from the mean surface temperature shall notexceed 60.5C. Temperature uniformity of the nude manikinshall be evaluated at least once annually using an infraredthermal imaging system or equivalent method. T

28、his procedureshall also be repeated after repairs or alterations are completedthat could affect temperature uniformity, for example, replace-ment of a heating element.5.2 Methods of Measuring Evaporative ResistanceTheevaporative resistance of a clothing system shall be measuredby measuring the power

29、 consumption of the manikin (Option 1in 8.6) or by measuring the evaporation rate of the liquidexiting the garment (Option 2 in 8.6).5.2.1 Power-Measuring InstrumentsIf power consump-tion method (Option 1) is used to calculate evaporativeresistance, the power to the manikin shall be measured so as t

30、ogive an average over the period of a test. If time proportioningor phase proportioning is used for power control, then devicesthat are capable of averaging over the control cycle arerequired. Integrating devices (watt-hour meters) are preferredover instantaneous devices (watt meters). Overall accur

31、acy ofthe power monitoring equipment must be within 62 % of thereading for the average power for the test period. Since thereare a variety of devices and techniques used for powermeasurement, no specified calibration procedures shall begiven. However, an appropriate power calibration procedure isto

32、be developed and documented.5.2.2 Equipment for Measuring Evaporative Water LossIfthe rate of evaporation method (Option 2) is used to calculateevaporative heat loss, the mass loss due to evaporation shall bemeasured by a set of balances to give an accurate average overthe period of a test. One bala

33、nce shall be used to measure theamount of water being fed to the manikin while the othermeasures the weight change of the manikin. Both balancesshall be calibrated yearly and have a resolution to the nearestgram.5.2.2.1 Measuring Water Dripping from the ManikinApan large enough to retain all water d

34、rippings from the manikinduring steady-state measurements, must be utilized if the rateof evaporation method (Option 2) is used to calculate theevaporative resistance of a clothing system. The captured watershall be measured at the end of the test with a calibrated4Information on laboratories with s

35、weating manikins can be obtained from theTextile Protection and Comfort Center, North Carolina State University, Raleigh,NC 27695 or from the Institute for Environmental Research, Kansas StateUniversity, Manhattan, KS 66506.F2370 152balance having a resolution to the nearest gram. Water lossfrom dri

36、pping is subtracted out of the evaporation rate used tocalculate evaporative resistance.DiscussionIf evaporation from the collection pan is aconcern, place a highly absorbent material (example: diaperlining) in the pan to collect and retain all liquid that has drippedfrom the manikin.5.3 Equipment f

37、or Measuring the Manikins Surface (Skin)TemperatureThe mean surface temperature shall be mea-sured with point sensors or distributed temperature sensors.5.3.1 Point SensorsPoint sensors shall be thermocouples,resistance temperature devices (RTDs), thermistors, or equiva-lent sensors. They shall be n

38、o more than 2 mm thick and shallbe well-bonded, both mechanically and thermally, to themanikins surface. Lead wires shall be bonded to the surface orpass through the interior of the manikin, or both. Each sensortemperature shall be area-weighted when calculating the meansurface temperature for the b

39、ody. A minimum of 15 pointsensors are required. At least one sensor shall be placed on thehead, chest, back, abdomen, buttocks, and both the right andleft upper arm, lower arm, hand, thigh, calf, and foot. Thesesensors must be placed in the same position for each test andthe placement of the sensors

40、 shall be given in the report.5.3.2 Distributed SensorsIf distributed sensors are used(for example, resistance wire), then the sensors must bedistributed over the surface so that all areas are equallyweighted. If several such sensors are used to measure thetemperature of different parts of the body,

41、 then their respectivetemperatures shall be area-weighted when calculating the meansurface temperature. Distributed sensors shall be less than 1mm in diameter and firmly attached to the manikin surface atall points.5.4 Controlled Environmental ChamberThe manikin shallbe placed in a chamber at least

42、1.5 by 1.5 by 2.5 m indimension that can provide uniform conditions, both spatiallyand temporally.5.4.1 Spatial VariationsSpatial variations shall not exceedthe following: air temperature 61C, relative humidity 65%,and air velocity 650 % of the mean value. In addition, themean radiant temperature sh

43、all not be more than 1.0Cdifferent from the mean air temperature. The spatial uniformityshall be verified at least annually or after any significantmodifications are made to the chamber. Spatial uniformity shallbe verified by recording values for the conditions stated aboveat heights of 0.1, 0.6, 1.

44、1, 1.4, and 1.7 m above the floor at thelocation occupied by the manikin. Sensing devices specifiedbelow shall be used when measuring the environmental con-ditions.5.4.2 Temporal VariationsTemporal variations shall notexceed the following: air temperature 60.5C, mean radianttemperature 60.5C, relati

45、ve humidity 65 %, air velocity620 % of the mean value for data averaged over 5 min. (see5.4.5).5.4.3 Relative Humidity Measuring EquipmentAny hu-midity sensing device with an accuracy of 65 % relativehumidity and a repeatability of 63 % is acceptable (forexample, wet bulb/dry bulb, dew point hygrome

46、ter). Only onelocation needs to be monitored during a test to ensure that thetemporal uniformity requirements are met.5.4.4 Air Temperature SensorsShielded air temperaturesensors shall be used. Any sensor with an overall accuracy of60.15C is acceptable (for example, RTD, thermocouple,thermistor). Th

47、e sensor shall have a time constant not exceed-ing 1 min. The sensor(s) shall be 0.5 m from the manikin. If asingle sensor is used, it shall be 1.0 m above the floor. Ifmultiple sensors are used, they shall be spaced at equal heightintervals and their readings averaged.5.4.5 Air Velocity IndicatorAn

48、 omni-directional anemom-eter with 60.05 m/s accuracy shall be used. Measurementsshall be averaged for at least 1 min at each location. If it isdemonstrated that velocity does not vary temporally by morethan 60.05 m/s, then it is not necessary to monitor air velocityduring a test. However, the value

49、 of the mean air velocity mustbe reported. If air velocity is monitored, then measurementlocation requirements are the same as for temperature.6. Sampling, Test Specimens, and Test Units6.1 SamplingIt is desirable to test three identical en-sembles to reflect sample variability. However, if only oneensemble is available (that is often the case with prototypegarments), replicate measurements shall be made on oneensemble.6.1.1 If only one ensemble is available, the garments mustbe removed from the manikin after each test, dried, andconditioned as