ASTM F434-1993(2009) Standard Test Method for Blow-Out Testing of Preformed Gaskets《预制衬垫的漏气的标准试验方法》.pdf
《ASTM F434-1993(2009) Standard Test Method for Blow-Out Testing of Preformed Gaskets《预制衬垫的漏气的标准试验方法》.pdf》由会员分享,可在线阅读,更多相关《ASTM F434-1993(2009) Standard Test Method for Blow-Out Testing of Preformed Gaskets《预制衬垫的漏气的标准试验方法》.pdf(3页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: F434 93 (Reapproved 2009)Standard Test Method forBlow-Out Testing of Preformed Gaskets1This standard is issued under the fixed designation F434; the number immediately following the designation indicates the year of originaladoption or, in the case of revision, the year of last revision
2、.Anumber in parentheses indicates the year of last reapproval.Asuperscriptepsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method covers the determination of the resis-tance against blow-out of preformed gaskets. The test isconducted under ambient
3、conditions and should be used forcomparison purposes only to select suitable designs andconstructions for specific applications.1.2 The values stated in SI units are to be regarded as thestandard. The values given in parentheses are for informationonly.1.3 This standard does not purport to address a
4、ll of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Adjuncts:Detailed Drawings of
5、Test Unit23. Significance and Use3.1 This test method is designed to compare all types ofpreformed gaskets under controlled conditions with respect toblow-out resistance. This test method may be used as a routinetest when agreed upon between the purchaser and the seller.4. Apparatus4.1 Pressure Supp
6、ly, capable of 7 MPa (1000 psi), prefer-ably hydraulic, and with proper safety precautions, in the eventof a rapid-gasket failure.4.2 Test Unit,3capable of withstanding 7 MPa (1000 psi)internal pressure under ambient conditions. Provisions shouldbe made for valve and pressure gage mountings, as show
7、n inFig. 1. The gage shall read from 0 to 7 MPa (0 to 1000 psi) andbe mounted so as to be visible at some distance.4.3 Booster PumpAn air-operated hydraulic (water) pres-sure pump, capable of delivering 1.1 3 105m3/s (40 in.3/min)against a back pressure of 35 MPa (5000 psi).4.4 Temperature Indicatin
8、g DeviceA thermometer ca-pable of reading 1C (2F) in the ambient temperature range.5. Test Specimen5.1 The specimen shall be a 102 mm (4-in.) nominal-sizegasket 114 mm (4.5 in.) in inside diameter by 165 mm (6.5 in.)in outside diameter. The thickness of the test gasket willdepend upon its expected u
9、sage and must be specified in thereport, as results will vary accordingly.6. Procedure6.1 Assemble the specimen in the test unit.6.2 The bolt threads should be well lubricated using moly-disulfide dry film or grease. Sanding the bottom of the boltheads and the washers will reduce torque variable and
10、 ensureduplication of results.6.3 Tighten the bolts, using the sequence shown in Fig. 2,increasing the torque loading in 25 % increments to thetargeted torque, but do not exceed the rating on the bolts.6.4 Fill the test unit with water, and bleed out all excess airby tilting until no further air bub
11、bles are forthcoming.6.5 Fill the oil reservoir (thermowell) three-quarters full oflight oil. Allow 15 min for the temperature to stabilize, andinsert the temperature sensor.6.6 Before applying hydrostatic pressure, cover the entiretest receptacle with a metal shield, leaving the gage exposedfor the
12、 recording of data.6.7 Attach a water hose from the booster pump, andgradually apply water pressure. This should be done under safeconditions, as follows:6.7.1 The operator should be wearing suitable safety equip-ment,6.7.2 The control valve should be located at a safe distancefrom the test area, an
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
5000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMF43419932009STANDARDTESTMETHODFORBLOWOUTTESTINGOFPREFORMEDGASKETS 预制 衬垫 漏气 标准 试验 方法 PDF
链接地址:http://www.mydoc123.com/p-536642.html