ASTM F1836M-2009(2013) Standard Specification for Stuffing Tubes Nylon and Packing Assemblies (Metric)《公制填料管 尼龙和包装配件的标准规范》.pdf

《ASTM F1836M-2009(2013) Standard Specification for Stuffing Tubes Nylon and Packing Assemblies (Metric)《公制填料管 尼龙和包装配件的标准规范》.pdf》由会员分享，可在线阅读，更多相关《ASTM F1836M-2009(2013) Standard Specification for Stuffing Tubes Nylon and Packing Assemblies (Metric)《公制填料管 尼龙和包装配件的标准规范》.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: F1836M 09 (Reapproved 2013) An American National StandardStandard Specification forStuffing Tubes, Nylon, and Packing Assemblies (Metric)1This standard is issued under the fixed designation F1836M; the number immediately following the designation indicates the year oforiginal adoption o

2、r, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1. Scope1

3、.1 This specification covers the general requirements fornylon stuffing tubes and packing assemblies. Nylon stuffingtubes are intended for making electric cable penetrations inmarine shipboard enclosures for electrical equipment. Thefollowing types are suitable for both thin-wall enclosures up to5mm

4、(316 in.) thick and thick-wall enclosures, bulkheads, anddecks of 5 to 19 mm (316 to34 in.) thick.1.2 This specification does not cover metal stuffing tubes.1.3 The values stated in SI units are to be regarded asstandard.1.4 This standard does not purport to address all of thesafety concerns, if any

5、, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to its use.2. Referenced Documents2.1 ASTM Standards:2D2000 Classification System for Rubber Products

6、 in Auto-motive ApplicationsD4066 Classification System for Nylon Injection and Extru-sion Materials (PA)2.2 NEMA Standards:Standard 250 Enclosures for Electrical Equipment (1000 VMax)32.3 ASME Standard:ASME B1.1 Unified Inch Screw Threads (UN and UNRThread Form)42.4 IEC StandardStandard 68-2-6 Envi

7、ronmental TestingPart 2: TestsTestFC: Vibration (Sinusoidal) Sixth Edition53. Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 nylon stuffng tube, na marine electrical fitting usedfor the sealing of cable penetration into shipboard enclosureswhile maintaining or exceeding the degr

8、ee of protection forwhich the enclosure is rated.3.1.2 packing assembly, nthe compressible insert for thenylon stuffing tube. It consists of one neoprene bushing andthree nylon washers.3.1.3 enclosure, nan electrical panel, cabinet, junctionbox, light fixture, electrical equipment, control box, or p

9、anel.4. Classification4.1 Nylon stuffing tubes shall be of the following types (seeFig. 1):4.1.1 Type 1straightUnified Form Thread.4.1.2 Type 290Unified Form Thread.4.1.3 Type 3NPTAmerican Standard Pipe Thread.4.1.4 Type 4YUnified Form Thread.5. Ordering Information5.1 Orders for stuffing tubes unde

10、r this specification shallinclude the following:5.1.1 Type (see 4.1).5.1.2 Part number (see Table 1).5.1.3 Packing assembly size (see Fig. 2 and Table 2).5.1.4 The O-ring included in the stuffing tube assembly hasa finite shelf life. If the stuffing tube assembly is used after theshelf life has expi

11、red, the O-ring should be replaced, using theappropriate size listed in Table 1.1This specification is under the jurisdiction of ASTM Committee F25 on Shipsand Marine Technology and is the direct responsibility of Subcommittee F25.10 onElectrical.Current edition approved Oct. 1, 2013. Published Octo

12、ber 2013. Originallyapproved in 1997. Last previous edition approved in 2009 as F1836M - 09. DOI:10.1520/F1836M-09R13.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer t

13、o the standards Document Summary page onthe ASTM website.3Available from National Electrical Manufacturers Association (NEMA), 1300N. 17th St., Suite 1752, Rosslyn, VA 22209, http:/www.nema.org.4Available from the International Electrotechnical Commission, 3 rue deVarembe, Case postale 131, CH-1211,

14、 Geneva 20, Switzerland.5Available from American Society of Mechanical Engineers (ASME), ASMEInternational Headquarters, Three Park Ave., New York, NY 10016-5990, http:/www.asme.org.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States15.1.

15、5 ASTM Part Number. The part number comprises theASTM specification number, type designator and assigneddash number as shown in the following example:F1836M Type-3 -002ASTMDesignatorPart TypeDesignatorSizeDesignatorExample: F1836M Type-3-002: Size 2 NPT stuffing tube(see Fig. 1).6. Materials and Man

16、ufacture6.1 Materials:6.1.1 Polyamide (nylon) molding plastic material shall beGroup 1, Class 8, Grade 1 in accordance with SpecificationD4066.6.1.2 Synthetic rubber (neoprene) shall be in accordancewith Classification D2000, M2, BC, 410, A14, B14, C12, andF19.6.2 Manufacture:6.2.1 Molded nylon part

17、s, such as body, washers, locknut,and cap, shall meet the requirements specified herein.6.2.2 Threads shall be unified form UN 2A or 2B or taperpipe thread (NPT) as specified in ASME Standard B1.1.FIG. 1 Stuffing Tube TypesF1836M 09 (2013)26.2.3 Neoprene parts, such as bushing and plug, shall meetth

18、e requirements specified in Classification D2000, and whenassembled in a stuffing tube, shall meet the performancerequirements specified herein.7. Other Requirements7.1 Performance Requirements:7.1.1 Vibration resistanceWhen stuffing tubes are testedas specified in 9.1, there shall be no evidence of

19、 cracking orloosening of parts.7.1.2 RuggednessWhen stuffing tubes are subjected to amechanical abuse test as specified in 9.2, there shall be nocracking, breaking, distortion, or damage to the sample.7.1.3 Effectiveness of sealWhen stuffing tubes are testedas specified in 9.3, there shall be no evi

20、dence of leakagethrough or around the stuffing tubes.8. Workmanship, Finish, and Appearance8.1 Stuffing tubes shall be free from warp, cracks, chippededges or surfaces, blisters, uneven surfaces, scratches, dents,and heat marks. They shall be free from fins, burrs, andunsightly finish caused by chip

21、ping, filing, or grinding withoutsubsequent buffing or polishing. All molded nylon parts shallbe cleaned thoroughly of annealing mediums. Packing assem-blies shall be free of voids, pin holes, flash, or otherimperfections, that may impair their serviceability.9. Test Methods9.1 Conformance testing o

22、f a random sample may berequested by the purchaser to verify that selected performancecharacteristics specified herein have been incorporated in thestuffing tube design and maintained in production.TABLE 1 Stuffing Tubes Part Numbers and Dimensional DataTube Part Cable Range Packing Clearance Hole D

23、iameter O-RingSize No. in. mm AssemblyAfor Tube Install Buna-Nmin. max. min. max. in. mm Size1 Type-1-001 0.077 0.300 1.96 7.62 -16 0.885 22.48 2122 -002 0.275 0.472 6.99 11.99 -17 1.010 25.65 2143 -003 0.410 0.472 10.41 11.99 -18 1.135 28.83 216Straight 4 -004 0.450 0.777 11.43 19.74 -19 1.260 32.0

24、0 218Type 1 4T -005 0.450 0.777 11.43 19.74 -19 1.385 35.18 2205 -006 0.752 1.113 19.10 28.27 -20 2.010 51.05 2266 -007 0.806 1.390 20.47 35.31 -21 2.510 63.75 2307 -008 1.433 1.610 36.40 40.89 -22 2.760 70.10 2328 -009 1.625 2.00 41.28 50.80 -23 3.260 82.80 2369 -010 2.030 2.700 51.56 68.58 -24 4.0

25、10 101.85 242Tube Part Cable Range Packing Clearance Hole Diameter O-RingSize No. in. mm AssemblyAfor Tube Install Buna-Nmin. max. min. max. in. mm Size1 Type-2-001 0.077 0.300 1.96 7.62 -16 0.885 22.48 21290 2 -002 0.275 0.472 6.99 11.99 -17 0.885 22.48 212Type 2 3 -003 0.410 0.472 10.41 11.99 -18

26、1.135 28.83 2164T -005 0.450 0.777 11.43 19.74 -19 1.260 32.00 2185 -006 0.752 1.113 19.10 28.27 -20 2.010 51.05 2206 -007 0.806 1.390 20.47 35.31 -21 2.510 63.75 230Tube Part Cable Range Packing NPTSize No. in. mm AssemblyAmin. max. min. max.1 Type-3-001 0.077 0.300 1.96 7.62 -16 0.52 -002 0.275 0.

27、472 6.99 11.99 -17 0.753 -003 0.410 0.472 10.41 11.99 -18 1.0NPT 4T -004 0.450 0.777 11.43 19.74 -19 1.0Type 3 5 -005 0.752 1.113 19.10 28.27 -20 1.56 -006 0.806 1.390 20.47 35.31 -21 27 -007 1.433 1.610 36.40 40.89 -22 2.58 -008 1.625 2.00 41.28 50.80 -23 39 -009 2.030 2.700 51.56 68.58 -24 3.5Tube

28、 Part Cable Ranges Packing Clearance Hole Diameter O-RingSize No. in. mm AssemblyAfor Tube Install Buna-Nmin. max. min. max. in. mm Size1 Type-4-001 0.077 0.300 1.96 7.62 -16 0.885 22.48 212Y 2 -002 0.275 0.472 6.99 11.99 -17 1.010 25.65 214Type 4 3 -003 0.410 0.472 10.41 11.99 -18 1.135 28.83 2164T

29、 -004 0.450 0.777 11.43 19.74 -19 1.385 35.18 220ASee Table 2 size selection.FIG. 2 Typical Packing AssemblyF1836M 09 (2013)39.1.1 VibrationThe stuffing tubes shall be subjected tovibration testing as specified in IEC Standard 68-2-6. Thefollowing details shall apply:9.1.1.1 The stuffing tubes shall

30、 be complete with O-ringsand 1- to 2-m (3- to 6-ft) lengths of cable of appropriate size.9.1.1.2 The free end of the cables shall be secured to preventexcessive cable whipping action during test.9.1.1.3 Tests are to be carried out in three perpendicularplanes.9.1.1.4 Duration of the test for no reso

31、nance condition shallbe 90 min at 30 Hz. Duration at each resonance frequency atwhich Q 2 is recorded. It is recommended as guidance that Qdoes not exceed 5.9.1.1.5 Test range shall be 2 6 0.3 Hz to 13.2 Hz amplitude 61 mm: 13.2 to 100 Hz acceleration 67g.9.1.1.6 Nonconformance to the requirements o

32、f 7.1.1 shallbe cause for rejection.9.2 Mechanical Abuse Test:9.2.1 Mechanical abuse test shall be conducted on thesample stuffing tubes assembled with packing assembly on theend of a 2-m (6-ft) length of electrical cable of appropriate size.9.2.2 The stuffing tube shall be allowed to swing on aradi

33、us, while suspended by the electrical cable, from a verticalsurface and strike against a vertical flat steel plate on thatsurface. The vertical distance through which the stuffing tube isallowed to fall shall be 1.5 m (5 ft), and the number of impactsshall be ten.9.2.3 The stuffing tube shall be dis

34、assembled and examined.Nonconformance to the requirements of 7.1.2 shall be cause forrejection.9.3 Level of EffectivenessA complete stuffing tube withO-ring installed and properly assembled to a cable or with aplug installed shall conform to the performance requirementsof NEMA 250. The NEMA enclosur

35、e-type designation (4, 4X,6, 6P) shall establish the appropriate environmental capability(see NEMA 250) required of the installed stuffing tube assem-bly.9.3.1 Nonconformance to the requirements of 7.1.3 shall because for rejection.10. Inspection10.1 Visual and Dimensional Examination Samples shallb

36、e examined visually to verify that the materials, design,construction, physical dimensions, marking, and workmanshipare as specified in the applicable requirements.TABLE 2 Packing Assembly SizeNOTE 1Packing assembly selection requires that the packing bushing inner diameter (D) be equal or slightly

37、larger than the cable maximum diameter(DIA).NOTE 2I.D. column indicates the bushing inner diameter.Cable Range Cable Rangein. mm in. mmTube Part I.D. I.D. Tube Part I.D. I.D.Size No. min. max. min. max. Size No. min. max. min. max.16-001 0.137 0.187 3.48 4.75 21-001 1.119 1.159 28.42 29.44-002 0.077

38、 0.127 1.96 3.23 -002 1.127 1.167 28.63 29.641-003 0.100 0.150 2.54 3.81 -003 1.160 1.200 29.46 30.48-004 0.184 0.234 4.67 5.94 -004 1.204 1.254 30.58 31.85-005 0.228 0.278 5.79 7.066-005 1.255 1.305 31.89 33.15-006 0.244 0.300 6.20 7.62 -006 1.309 1.350 33.25 34.2917-001 0.275 0.325 6.99 8.26 -007

39、1.350 1.390 34.29 35.112-002 0.317 0.367 8.05 9.32 -008 0.856 0.886 21.74 22.50-003 0.340 0.390 8.64 9.91 -009 0.926 0.956 23.52 24.28-004 0.375 0.425 9.53 10.80 -010 0.776 0.806 19.71 20.47-005 0.422 0.472 10.72 11.99 22-001 1.418 1.458 36.02 37.033 18-018 0.410 0.472 10.41 11.997-002 1.460 1.500 3

40、7.08 38.1019-001 0.450 0.500 11.43 12.70 -003 1.510 1.566 38.35 39.78-002 0.497 0.547 12.62 13.89 -004 1.570 1.610 39.88 40.89-003 0.534 0.584 13.56 14.83 23-001 1.610 1.641 40.89 41.684 -004 0.559 0.609 14.20 15.47 -002 1.645 1.688 41.78 42.87and -005 0.610 0.665 15.49 16.89 -003 1.695 1.735 43.05

41、44.074T -006 0.650 0.700 16.51 17.78 8 -004 1.745 1.812 44.32 46.03-007 0.669 0.719 16.99 18.26 -005 1.816 1.859 46.13 47.22-008 0.727 0.777 18.47 19.74 -006 1.860 1.906 47.24 48.41-009 0.710 0.760 18.03 19.30 -007 1.905 1.935 48.39 49.1520-001 0.737 0.777 18.72 19.74 -008 1.940 2.000 49.28 50.80-00

42、2 0.772 0.812 19.61 20.63 24-001 2.006 2.046 50.95 51.97-003 0.813 0.853 20.65 21.67 -002 2.050 2.093 52.07 53.16-004 0.849 0.889 21.57 22.58 -003 2.100 2.140 53.34 54.36-005 0.889 0.937 22.58 23.80 -004 2.150 2.285 54.61 58.045 -006 0.937 0.980 23.80 24.89 9 -005 2.295 2.385 58.29 60.05-007 0.981 1

43、.021 24.92 25.93 -006 2.375 2.418 60.33 61.42-008 1.000 1.042 25.40 26.47 -007 2.428 2.540 61.67 64.52-009 1.033 1.073 26.24 27.25 -008 2.560 2.700 65.02 68.58-010 1.073 1.113 27.25 28.27F1836M 09 (2013)411. Certification11.1 Plastic Material Certification Material certificationshall be required fro

44、m the manufacturer of the plastic materialto ensure the material was manufactured, sampled, tested, andinspected in accordance with Specification D4066. Materialidentity, traceable to this certification, shall be maintainedthroughout the manufacturing process.11.2 Cure date information of all rubber

45、 products shall berecorded on the manufacturers certificate of conformance. Theyear and quarter of manufacture shall be listed.11.3 When specified in the purchase order or contract, thepurchaser shall be furnished certification that samples repre-senting each lot have been either tested or inspected

46、 as directedin this specification and the requirements have been met. Whenspecified in the purchase order or contract, a report of the testresults shall be furnished.12. Product Marking12.1 Each nylon stuffing tube component body, locknut,cap, bushing, and washers shall have permanent marking in3-mm

47、 (18-in.) high raised letters as size permits. For size-sensitive components, reduced marking is acceptable. Markingshall indicate the following:12.1.1 Manufacturers name or trademark and tube size.12.1.2 Identification markings of prior or superseded speci-fications or government drawings. These ma

48、rkings are accept-able. New molds or molds that require rework shall contain, ifrequired, the ASTM designation number of this specificationand part number. The location of the ASTM marking shallapply to the stuffing tube only and be located on the stuffingtube body. Marking in accordance with 12.1.1

49、 shall apply to allstuffing tube components.13. Packaging13.1 Packaging shall be manufacturers commercial prac-tice and shall be sufficient to afford adequate protection againstdeterioration and physical damage during shipment from themanufacturer or supplier, or both, to the using activity.NOTE 1Bulk packaging for nylon stuffing tubes; unit packaging forpacking assemblies.14. Quality Assurance14.1 Responsibility for Inspection Unless otherwise speci-fied in the contract or purchase order, the manufacturer isresponsible for the performance of