ASTM F1733-2013 Standard Specification for Butt Heat Fusion Polyamide(PA) Plastic Fitting for Polyamide(PA) Plastic Pipe and Tubing《聚酰胺 (PA) 塑料管和软管用对接热熔接聚酰胺 (PA) 塑料配件的标准规范》.pdf

《ASTM F1733-2013 Standard Specification for Butt Heat Fusion Polyamide(PA) Plastic Fitting for Polyamide(PA) Plastic Pipe and Tubing《聚酰胺 (PA) 塑料管和软管用对接热熔接聚酰胺 (PA) 塑料配件的标准规范》.pdf》由会员分享，可在线阅读，更多相关《ASTM F1733-2013 Standard Specification for Butt Heat Fusion Polyamide(PA) Plastic Fitting for Polyamide(PA) Plastic Pipe and Tubing《聚酰胺 (PA) 塑料管和软管用对接热熔接聚酰胺 (PA) 塑料配件的标准规范》.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: F1733 07F1733 13 An American National StandardStandard Specification forButt Heat Fusion Polyamide(PA) Plastic Fitting forPolyamide(PA) Plastic Pipe and Tubing1This standard is issued under the fixed designation F1733; the number immediately following the designation indicates the year

2、oforiginal adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope Scope*1.1 This specification covers polyamide (PA) butt fusi

3、on fittings for use with polyamide pipe (IPS and ISO) and tubing (CTS).Included are requirements for materials, workmanship, dimensions, marking, sustained pressure, and burst pressure.1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathe

4、maticalconversions to SI units that are provided for information only and are not considered standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibilityof the user of this standard to establish appropriate safety and he

5、alth practices and determine the applicability of regulatorylimitations prior to use.2. Referenced Documents2.1 ASTM Standards:2NOTE 1For over 40 years D2513 was the singular US CFR Title 49 Part 192 referenced Standard Specification codifying the installation and use ofthermoplastic gas piping in j

6、urisdictional installations. Initially all materials (PE, PVC,ABS, CAB) were contained within the body of the standard D2513.In later years D2513 was completely reformatted to make it more user friendly by moving material-specific requirements from the standards body tomandatory annexes. The next ma

7、jor change occurred late in 2009 at which time all thermoplastic materials, except polyethylene, were removed fromD2513 changing its Title and Scope from a thermoplastic gas piping standard to a polyethylene-only gas piping standard. This recent change requiredthat new standards be developed for tho

8、se materials that were removed from D2513 including PA11. This causes problems for PA11 piping because ithas been referenced and permitted for jurisdictional use and installation under US CFR Title 49 Part 192 as complying with D2513 and D2513 no longerhas the A5 polyamide annex and Part 192 still r

9、eferences D2513-99 which makes for potential confusion. This puts PA11 gas piping standards intosomewhat of a limbo since D2513 is now a PE-only specification is referenced in all of these standards. Therefore until Part 192 is revised to referencethe new PA11 specification, F2945, PA11 has to fall

10、back to citing the US Code referenced 1999 edition of D2513 in related standard such as this one.Until CFR Title 49 Part 192 references the newly developed thermoplastic gas piping standards for those materials removed from D2513, there will bedual references, both D251399 and F2945 for PA11, as see

11、n in this standard. At which time Part 192 references F2945, the PA11 gas piping standard,all references to D2513 and this note will be removed from these standards.D1598 Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal PressureD1599 Test Method for Resistance to Short-Time Hy

12、draulic Pressure of Plastic Pipe, Tubing, and FittingsD1600 Terminology for Abbreviated Terms Relating to PlasticsD2122 Test Method for Determining Dimensions of Thermoplastic Pipe and FittingsD2513 Specification for Thermoplastic Gas Pressure Pipe, Tubing, and FittingsD4066 Classification System fo

13、r Nylon Injection and Extrusion Materials (PA) (Withdrawn 2012)3D6779 Classification System for and Basis of Specification for Polyamide Molding and Extrusion Materials (PA)F412 Terminology Relating to Plastic Piping SystemsF2785 Specification for Polyamide 12 Gas Pressure Pipe, Tubing, and Fittings

14、F2945 Specification for Polyamide 11 Gas Pressure Pipe, Tubing, and Fittings2.2 Federal Standard:4Fed. Std. No. 123 Marking for Shipment (Civil Agencies)CFR Title 49 Part 192 Transportation of Natural and Other Gas By Pipeline: Minimum Federal Safety Standards1 This specification is under the jurisd

15、iction of ASTM Committee F17 on Plastic Piping Systems and is the direct responsibility of Subcommittee F17.10 on Fittings.Current edition approved Nov. 1, 2007May 1, 2013. Published November 2007May 2013. Originally approved in 1996. Last previous edition approved in 20022007 asF173306(2002).F17330

16、7. DOI: 10.1520/F1733-07.10.1520/F1733-13.2 For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at serviceastm.org. For Annual Book of ASTM Standardsvolume information, refer to the standards Document Summary page on the ASTM website.3 The last approved

17、 version of this historical standard is referenced on www.astm.org.4 Available from Standardization Documents Order Desk, Bldg. 4 Section D, 700 Robbins Ave., Philadelphia, PA 19111-5094, Attn: NPODS.This document is not an ASTM standard and is intended only to provide the user of an ASTM standard a

18、n indication of what changes have been made to the previous version. Becauseit may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current versionof the standard as published by ASTM is t

19、o be considered the official document.*A Summary of Changes section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States12.3 Military Standard:MIL-STD-129 Marking for Shipment and Storage42.4 National San

20、itation Foundation Standard:Standard No. 14 for Plastic Piping Components and Related Materials53. Terminology3.1 Definitions are in accordance with Terminology F412 and abbreviations are in accordance with Terminology D1600, unlessotherwise specified.3.2 dimension ratio (DR) for thermoplastic pipet

21、he ratio of diameter to wall thickness. For this specification it is calculatedby dividing the specified outside diameter by the specified wall thickness of the fitting at its area of fusion. DRs are rounded anddo not calculate exactly.4. Classification4.1 GeneralThis specification covers butt fusio

22、n fittings intended for use with polyamide pipe and tubing.4.1.1 Fittings covered by this specification are normally molded. Fittings may be machined from extruded or molded stock.4.1.2 Fittings fabricated by thermal welding are not included in this specification.4.1.3 Fittings intended for use in t

23、he distribution of natural gas or petroleum fuels shall also meet the requirements ofSpecification D2513. 99 and Specification F2945 for PA11 materials or Specification F2785 for PA12 materials.5. Ordering Information5.1 When ordering fittings under this specification, the following should be specif

24、ied:5.1.1 Polyamide compound (material designation or trade name)5.1.2 Style of fitting (tee, 90 ell, and the like)5.1.3 Size:5.1.3.1 Nominal diameter.5.1.3.2 CTS, IPS, or schedule.5.1.3.3 Dimension ratio number or schedule number.6. Materials6.1 Basic MaterialsThis specification covers fittings mad

25、e from polyamide plastics as defined in SpecificationSpecificationsD4066 or D6779.NOTE 2The PAplastic fittings intended for use in the transport of potable water should be evaluated and certified as safe for this purpose by a testingagency acceptable to the local health authority. The evaluation sho

26、uld be in accordance with requirements for chemical extraction, taste, and odor, thatare no less restrictive than those included in National Sanitation Foundation (NSF) Standard No. 14. The seal or mark of the laboratory making theevaluation should be included on the pipe and tubing.6.2 CompoundsThe

27、 polyamide fittings compounds shall meet the requirements for Group 3, Class 2, and Grade 3, or Group4, Class 2 and Grade 3 as prescribed in SpecificationSpecifications D4066 or D6779.NOTE 3Fittings produced from compounds meeting the requirements of Group 3, Class 2, and Grade 3 (PA 323) are intend

28、ed for use with pipemanufactured from compounds meeting the requirements of Group 3, Class 2, and Grade 3. Fittings produced from compounds meeting the requirementsof Group 4, Class 2, and Grade 3 (PA 423) are intended for use with pipe manufactured from compounds meeting the requirements of Group 4

29、, Class2, and Grade 3. As per the recommendations of respective resin manufacturers, no cross fusion between PA 323 pipe and fittings and PA 423 pipe andfittings is permitted.6.3 Rework MaterialClean rework material generated from the manufacturers own production may be used by the samemanufacturer

30、as long as the fittings produced conform to the requirements of this specification.7. Requirements7.1 Dimensions and Tolerances:7.1.1 Outside DiameterNominal outside diameters of butt fusion fittings shall conform to the nominal iron pipe size (IPS) orcopper tubing size (CTS) dimensions at area of f

31、usion. These dimensions and tolerances shall be as shown in Table 1, Table 2,and Table 3 of this specification.7.1.2 Inside Diameter (CTS Fittings Only)Inside diameters of butt fusion fittings for tubing at area of fusion shall conformto the dimensions of the tubing being joined. The dimensions and

32、tolerances for the fittings are shown in Table 3.7.1.3 Wall ThicknessThe wall thicknesses of butt fusion fittings shall not be less than the minimum specified for the pipe ortubing. The wall thicknesses and tolerances at the area of fusion shall be as shown in Table 3, Table 4, and Table 5 of thissp

33、ecification.5 Available from NSF International, P.O. Box 130140, 789 N. Dixboro Rd., Ann Arbor, MI 48113-0140, http:/www.nsf.org.F1733 1327.1.4 MeasurementsThese shall be made in accordance with Test Method D2122 for roundable pipe.7.1.5 Design DimensionsOverall fitting dimensions may be as preferre

34、d from a design standpoint by the manufacturer andaccepted by the purchaser consistent with 7.1.3.7.2 Pressure Test Requirements :7.2.1 Short-Term Rupture Strength for Fittings 12 to 12 in. and 90 to 315 mm, Nominal DiameterThe minimum short-termrupture strength of the fitting and fused pipe or tubi

35、ng shall not be less than the minimum short-term rupture strength of the pipeor tubing in the system when tested in accordance with 10.5.3. These minimum pressures shall be as shown in Table 6 of thisspecification. Test specimens shall be prepared for testing in the manner described in 10.5.1 of thi

36、s specification. The testequipment, procedures, and failures definitions shall be as specified in Test Method D1599.TABLE 1 IPS Sizing System Outside Diameters and Tolerancesfor Fittings for Use with Polyamide Pipe, in.Nominal PipeSizeAverage Outside Diameterat Area of FusionA Tolerance12340.8401.05

37、00.0080.0081 1.315 0.010114 1.660 0.010112 1.900 0.0102 2.375 0.0103 3.500 0.0124 4.500 0.0156 6.625 0.0188 8.625 0.02510 10.750 0.02712 12.750 0.03614 14.000 0.06316 16.000 0.07218 18.000 0.08120 20.000 0.09021.5 21.500 0.09722 22.000 0.09924 24.000 0.10828 28.000 0.12632 32.000 0.14436 36.000 0.16

38、242 42.000 0.18948 48.000 0.216A Defined as measured 14 in. (6.4 mm) from fitting outlet extremity.TABLE 2 ISO Sizing System (ISO 161/1) Outside Diameters andTolerances for Fit for Use with Polyamide Pipe, (mm)Nominal PipeSizeAverage Outside Diameter at Area of FusionMin MaxA90 90.0 90.8110 110.0 11

39、1.0160 160.0 161.4200 200.0 201.8250 250.0 252.3280 280.0 282.5315 315.0 317.8355 355.0 358.2400 400.0 403.6450 450.0 454.1500 500.0 504.5560 560.0 565.0630 630.0 635.7710 710.0 716.4800 800.0 807.2900 900.0 908.11000 1000.0 1009.01200 1200.0 1210.81400 1400.0 1412.61600 1600.0 1614.4A Specified in

40、ISO 3607.F1733 1337.2.2 Short-Term Strength for Fittings 14 to 48 in. and 355 to 1600 mm, Nominal DiameterFittings shall not fail when testedin accordance with 10.5.3. The minimum pressure shall be as shown in Table 6 of this specification. Test specimens shall beprepared for testing in the manner d

41、escribed in 10.2 of this specification. The test equipment and procedures shall be as specifiedin Test Method D1599.7.2.3 Sustained PressureThe fitting and fused pipe or tubing shall not fail, as defined in Test Method D1598, when tested atthe time, pressures, and test temperatures selected from tes

42、t options offered in Table 7. The test specimens shall be prepared fortesting in the manner prescribed in 10.5.1.8. Workmanship, Finish, and Appearance8.1 The manufacture of these fittings shall be in accordance with good commercial practice so as to produce fittings meetingthe requirements of this

43、specification. Fittings shall be homogeneous throughout and free of cracks, holes, foreign inclusions, orother injurious defects. The fittings shall be as uniform as commercially practicable in color, opacity, density, and other physicalproperties.TABLE 3 Diameter, Wall Thickness, and Tolerances for

44、 Fittings for Use with Polyamide TubingTubing Type,in. (mm)Nominal TubingSize, in.Diameter at Area of FusionAMinimum WallThickness, in. (mm)Outside, in. (mm) Inside, in. (mm)Average Tolerance Average Tolerance0.062 (1.57) 12 CTS34 CTS0.625 (15.88)0.875 (22.22)0.010 (0.26)0.010 (0.26)0.495 (12.58)0.7

45、45 (18.92)0.004 (0.10). . .0.062 (1.58). . .0.090 (2.29) 12 CTS 0.625 (15.88) 0.010 (0.26) 0.437 (11.10) 0.004 (0.10) 0.090 (2.28)34 CTS 0.875 (22.22) 0.010 (0.26) 0.687 (17.44) 0.004 (0.10) 0.090 (2.28)1 CTS 1.125 (28.58) 0.013 (0.34) 0.937 (23.80) 0.005 (0.12) 0.090 (2.28)114 CTS 1.375 (34.92) 0.0

46、13 (0.34) 1.187 (30.14) 0.005 (0.12) 0.090 (2.28)DR 11 34 CTS1 CTS114 CTS0.875 (22.22)1.125 (28.58)1.375 (34.92)0.010 (0.26)0.013 (0.34)0.013 (0.34)0.715 (18.16)0.915 (23.24)1.125 (28.58)0.004 (0.10)0.005 (0.12)0.005 (0.12)0.077 (1.96)0.101 (2.56)0.121 (3.08)DR 9.3 12 CTS 0.625 (15.88) 0.010 (0.26)

47、0.483 (12.26) 0.004 (0.10) 0.067 (1.70)34 CTS 0.875 (22.22) 0.010 (0.26) 0.679 (17.24) 0.004 (0.10) 0.094 (2.38)1 CTS 1.125 (28.58) 0.013 (0.34) 0.873 (22.18) 0.005 (0.12) 0.121 (3.08)114 CTS 1.375 (34.92) 0.013 (0.34) 1.069 (27.16) 0.005 (0.12) 0.148 (3.76)A Defined as measured 14 in. (6.4 mm) from

48、 fitting outlet extremity.TABLE 4 IPS Sizing System Wall Thickness and Tolerance at the Area of Fusion for Fittings for Use with Polyamide Pipe, in.A,B,CNominal PipeSizeMinimum Wall ThicknessSCH 40 SCH 80 SDR 21 SDR 17 SDR 13.5 DR 10 DR 11.5 SDR 11 DR 9.3 SDR 912 0.109 0.147 . . . . . . . . . . . .

49、. . . 0.076 0.090 . . .34 0.113 0.154 . . . . . . . . . . . . . . . 0.095 0.113 0.1171 0.133 0.179 . . . . . . . . . . . . . . . 0.119 0.142 0.146114 0.140 0.191 . . . . . . . . . 0.166 . . . 0.151 0.179 0.184112 0.145 0.200 . . . . . . . . . . . . . . . 0.173 0.204 0.2112 0.154 0.218 . . . . . . . . . . . . . . . 0.216 0.256 0.2643 0.216 0.300 . . . . . . 0.259 . . . 0.305 0.318 0.377 0.3894 0.237 0.337 . . . 0.264 0.333 . . . 0.392 0.409 0.484 0.5006 0.280 0.432