ASTM D7156-2015 9699 Standard Test Method for Evaluation of Diesel Engine Oils in the T-11 Exhaust Gas Recirculation Diesel Engine《T-11废气再循环柴油发动机中柴油评估的标准试验方法》.pdf

《ASTM D7156-2015 9699 Standard Test Method for Evaluation of Diesel Engine Oils in the T-11 Exhaust Gas Recirculation Diesel Engine《T-11废气再循环柴油发动机中柴油评估的标准试验方法》.pdf》由会员分享，可在线阅读，更多相关《ASTM D7156-2015 9699 Standard Test Method for Evaluation of Diesel Engine Oils in the T-11 Exhaust Gas Recirculation Diesel Engine《T-11废气再循环柴油发动机中柴油评估的标准试验方法》.pdf（35页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D7156 15Standard Test Method forEvaluation of Diesel Engine Oils in the T-11 Exhaust GasRecirculation Diesel Engine1This standard is issued under the fixed designation D7156; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revis

2、ion, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope*1.1 This test method covers an engine test procedure forevaluating diesel engine oils for performance ch

3、aracteristics ina diesel engine equipped with exhaust gas recirculation,including viscosity increase and soot concentrations (loading).2This test method is commonly referred to as the Mack T-11.1.1.1 This test method also provides the procedure forrunning an abbreviated length test, which is commonl

4、y referredto as the T-11A. The procedures for the T-11A are identical tothe T-11 with the exception of the items specifically listed inAnnex A8. Additionally, the procedure modifications listed inAnnex A8 refer to the corresponding section of the T-11procedure.1.2 The values stated in SI units are t

5、o be regarded asstandard. No other units of measurement are included in thisstandard.1.2.1 ExceptionsWhere there is no direct SI equivalentsuch as screw threads, National Pipe Threads/diameters, tubingsize, or where there is a sole source supply equipmentspecification.1.3 This standard does not purp

6、ort to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use. See Annex A6 forspecific safety hazards.2. Re

7、ferenced Documents2.1 ASTM Standards:3D86 Test Method for Distillation of Petroleum Products atAtmospheric PressureD93 Test Methods for Flash Point by Pensky-MartensClosed Cup TesterD97 Test Method for Pour Point of Petroleum ProductsD130 Test Method for Corrosiveness to Copper from Petro-leum Produ

8、cts by Copper Strip TestD235 Specification for Mineral Spirits (Petroleum Spirits)(Hydrocarbon Dry Cleaning Solvent)D287 Test Method for API Gravity of Crude Petroleum andPetroleum Products (Hydrometer Method)D445 Test Method for Kinematic Viscosity of Transparentand Opaque Liquids (and Calculation

9、of Dynamic Viscos-ity)D482 Test Method for Ash from Petroleum ProductsD524 Test Method for Ramsbottom Carbon Residue ofPetroleum ProductsD613 Test Method for Cetane Number of Diesel Fuel OilD664 Test Method for Acid Number of Petroleum Productsby Potentiometric TitrationD976 Test Method for Calculat

10、ed Cetane Index of DistillateFuelsD1319 Test Method for Hydrocarbon Types in Liquid Petro-leum Products by Fluorescent Indicator AdsorptionD2274 Test Method for Oxidation Stability of Distillate FuelOil (Accelerated Method)D2500 Test Method for Cloud Point of Petroleum ProductsD2622 Test Method for

11、Sulfur in Petroleum Products byWavelength Dispersive X-ray Fluorescence SpectrometryD2709 Test Method for Water and Sediment in MiddleDistillate Fuels by Centrifuge1This test method is under the jurisdiction of ASTM Committee D02 onPetroleum Products, Liquid Fuels, and Lubricants and is the direct r

12、esponsibility ofSubcommittee D02.B0 on Automotive Lubricants.Current edition approved Oct. 1, 2015. Published October 2015. Originallyapproved in 2005. Last previous edition approved in 2013 as D7156 13. DOI:10.1520/D7156-15.2The ASTM Test Monitoring Center (TMC) will update changes in this testmeth

13、od by means of Information Letters. This edition includes all informationletters through 151. Information letters may be obtained from the ASTM TestMonitoring Center, 6555 Penn Ave., Pittsburgh, PA 15206-4489, Attention: Admin-istrator.3For referenced ASTM standards, visit the ASTM website, www.astm

14、.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box

15、C700, West Conshohocken, PA 19428-2959. United States1D3524 Test Method for Diesel Fuel Diluent in Used DieselEngine Oils by Gas ChromatographyD4052 Test Method for Density, Relative Density, and APIGravity of Liquids by Digital Density MeterD4175 Terminology Relating to Petroleum, PetroleumProducts

16、, and LubricantsD4294 Test Method for Sulfur in Petroleum and PetroleumProducts by Energy Dispersive X-ray Fluorescence Spec-trometryD4485 Specification for Performance of Active API ServiceCategory Engine OilsD4737 Test Method for Calculated Cetane Index by FourVariable EquationD4739 Test Method fo

17、r Base Number Determination byPotentiometric Hydrochloric Acid TitrationD5185 Test Method for Multielement Determination ofUsed and Unused Lubricating Oils and Base Oils byInductively Coupled Plasma Atomic Emission Spectrom-etry (ICP-AES)D5453 Test Method for Determination of Total Sulfur inLight Hy

18、drocarbons, Spark Ignition Engine Fuel, DieselEngine Fuel, and Engine Oil by Ultraviolet FluorescenceD5967 Test Method for Evaluation of Diesel Engine Oils inT-8 Diesel EngineD6278 Test Method for Shear Stability of Polymer Contain-ing Fluids Using a European Diesel Injector ApparatusD6896 Test Meth

19、od for Determination of Yield Stress andApparent Viscosity of Used Engine Oils at Low Tempera-tureD7109 Test Method for Shear Stability of Polymer Contain-ing Fluids Using a European Diesel Injector Apparatus at30 and 90 CyclesD7422 Test Method for Evaluation of Diesel Engine Oils inT-12 Exhaust Gas

20、 Recirculation Diesel EngineE29 Practice for Using Significant Digits in Test Data toDetermine Conformance with Specifications3. Terminology3.1 Definitions:3.1.1 blind reference oil, na reference oil, the identity ofwhich is unknown by the test facility.3.1.1.1 DiscussionThis is a coded reference oi

21、l that issubmitted by a source independent from the test facility. D41753.1.2 blowby, nin internal combustion engines, that por-tion of the combustion products and unburned air/fuel mixturethat leaks past piston rings into the engine crankcase duringoperation.3.1.3 calibrate, vto determine the indic

22、ation or output of adevice (for example, thermometer, manometer, engine) withrespect to that of a standard.3.1.4 candidate oil, nan oil that is intended to have theperformance characteristics necessary to satisfy a specificationand is intended to be tested against that specification. D41753.1.5 exha

23、ust gas recirculation (EGR), nthe mixing ofexhaust gas with intake air to reduce the formation of nitrogenoxides (NOx). Automotive Handbook43.1.6 heavy-duty, adj in internal combustion engineoperation, characterized by average speeds, power output andinternal temperatures that are close to the poten

24、tial maximums.D44853.1.7 heavy-duty engine, nin internal combustion enginetypes, one that is designed to allow operation continuously at orclose to its peak output.3.1.8 non-reference oil, nany oil other than a referenceoil; such as a research formulation, commercial oil, or candi-date oil. D41753.1

25、.9 non-standard test, na test that is not conducted inconformance with the requirements in the standard testmethod; such as running on an uncalibrated test stand, usingdifferent test equipment, applying different equipment assem-bly procedures, or using modified operating conditions. D41753.1.10 oxi

26、dation, nof engine oil, the reaction of the oilwith an electron acceptor, generally oxygen, that can producedeleterious acidic or resinous materials often manifested assludge formation, varnish formation, viscosity increase, orcorrosion, or combination thereof.3.1.11 reference oil, nan oil of known

27、performancecharacteristics, used as a basis for comparison.3.1.11.1 DiscussionReference oils are used to calibratetesting facilities, to compare the performance of other oils, orto evaluate other materials (such as seals) that interact withoils. D41753.1.12 sludge, nin internal combustion engines, a

28、 deposit,principally composed of insoluble resins and oxidation prod-ucts from fuel combustion and the lubricant, that does not drainfrom engine parts but can be removed by wiping with a cloth.D41753.1.13 standard test, na test on a calibrated test stand,using the prescribed equipment that is assemb

29、led in accordancewith the requirements in the test method, and conducted inaccordance with the specified operating conditions.3.1.14 varnish, nin internal combustion engines, a hard,dry, generally lustrous deposit that can be removed by solventsbut not by wiping with a cloth. D41753.1.15 wear, nthe

30、loss of material from a surface, gener-ally occurring between two surfaces in relative motion, andresulting from mechanical or chemical action, or a combinationof both. D74224. Summary of Test Method4.1 The test operation involves use of a Mack E-TECHV-MAC III diesel engine with Exhaust Gas Recircul

31、ation(EGR). Two oil flushes, each for 30 min, are followed by a testat constant speed and torque conditions for 252 h.4Available from Robert Bosch GmbH, Postfach 50, D-7000 Stuttgart 1,Germany.D7156 1524.2 Take oil samples periodically and analyze for viscosityincrease and soot content.4.3 Engine re

32、builds may be necessary as indicated bydegradation of test parameters and are left to the discretion ofthe test laboratory. At rebuild, the power section of the engineis disassembled, solvent-cleaned, and rebuilt, using all newpistons, rings, cylinder liners, valves, and valve guides, in strictaccor

33、dance with furnished specification.4.4 Solvent-clean the engine crankcase and replace worn ordefective parts.4.5 Equip the test stand with appropriate accessories forcontrolling speed, torque, and various engine operating condi-tions.5. Significance and Use5.1 This test method was developed to evalu

34、ate the viscosityincrease and soot concentration (loading) performance ofengine oils in turbocharged and intercooled four-cycle dieselengines equipped with EGR. Obtain results from used oilanalysis.5.2 The test method can be used for engine oil specificationacceptance when all details of the procedu

35、re are followed.6. Apparatus6.1 General Description:6.1.1 The test engine is a Mack E-TECH V-MAC III,electronically controlled fuel injection with six electronic unitpumps, using 2002 cylinder heads (Annex A2). It is an open-chamber, in-line, six-cylinder, four-stroke, turbocharged,charge air-cooled

36、, and compression ignition engine. The boreand stroke are 124 mm by 165 mm, and the displacement is12 L.6.1.2 The ambient laboratory atmosphere shall be relativelyfree of dirt and other contaminants as required by goodlaboratory standards. Filtering air, controlling temperature, andcontrolling humid

37、ity in the engine buildup area helps preventaccumulation of dirt and other contaminants on engine partsand aids in measuring and selecting parts for assembly.6.2 The Test Engine:6.2.1 Mack T-11 Test EngineThe engine and cylinderheads are available from Mack Trucks, Inc.5A complete partslist is shown

38、 in Table A2.1, Annex A2. Use test parts on afirst-in/first-out basis.6.2.2 Engine Cooling System:6.2.2.1 Use a new Mack coolant conditioner shown in TableA2.1, Annex A2, every test, to limit scaling in the coolingsystem. At the expansion tank, pressurize the system to103 kPa. Use the coolant shown

39、in 7.3.6.2.2.2 Use a closed-loop, pressurized external engine cool-ing system composed of a nonferrous core heat exchanger,reservoir, and water-out temperature control valve. The systemshall prevent air entrainment and control jacket temperatureswithin the specified limit. Install a sight glass betw

40、een theengine and the cooling tower to check for air entrainment anduniform flow in an effort to prevent localized boiling. Block thethermostat wide open.6.2.2.3 Flow the coolant from the engine block fitting to theEGR coolers, see Fig. A1.3, Annex A1. Return the EGRcoolant flow to the engine coolan

41、t-in line, near the coolantpump inlet, see Fig. A1.7, Annex A1.6.2.3 Auxiliary Oil System:6.2.3.1 To maintain a constant oil level in the pan, providean additional minimum volume sump of 11.4 L by using aseparate closed tank connected to the engine sump. Circulateoil through the system with an auxil

42、iary pump. The systemschematic is shown in Fig. A1.1, Annex A1. The insidediameters of the No. 6 and No. 8 lines are 10 mm and 13 mm,respectively. Use a minimum No. 8 size vent line. Equivalentlines may be substituted forAeroquip6lines provided they havethe proper inside diameters.6.2.3.2 Locate the

43、 auxiliary oil system suction line on theexhaust side of the oil pan, so that the inside bottom of theauxiliary oil system suction fitting is down from the oil pan railby 152 mm, and back from the front of the pan by 178 mm.Refer to Fig.A1.4, AnnexA1. Connect the auxiliary oil systemreturn line to t

44、he power steering pump cover on the fronttiming gear cover. Refer to Fig. A1.5, Annex A1. Connect theauxiliary oil scale vent line to the top of the auxiliary oil sumpbucket and the dipstick tube opening.6.2.3.3 Use Viking Pump Model SG053514 as the auxiliaryoil pumps (see A2.10). Nominal pump speed

45、 is 1725 rmin.Shut off the auxiliary oil pumps if the auxiliary oil system goesdry.6.2.3.4 Use a sight glass to aid in determining the oil levelshould the auxiliary oil system run dry. An example of a sightglass setup is shown in Fig. A1.18, Annex A1.6.2.4 Oil Cooling System:6.2.4.1 Use the oil cool

46、er adapter blocks to mount the oilcooler to the engine. The adapter blocks are available from thesupplier list in A2.7, Annex A2.6.2.4.2 Use the oil filter housing (part number 27GB525M)shown in Fig. A1.8, Annex A1.6.2.5 Blowby MeterUse a meter capable of providing dataat a minimum frequency of 6 mi

47、n. To prevent blowby conden-sate from draining back into the engine, ensure the blowby linehas a downward slope to a collection bucket. Ensure thecollection bucket has a minimum volume of 18.9 L. Locate theblowby meter downstream of the collection bucket. The slopeof the blowby line downstream of th

48、e collection bucket isunspecified.6.2.6 Air Supply and FiltrationUse the Mack air filterelement and the Mack filter housing shown in A2.3, AnnexA2.Replace the filter cartridge when a P of 2.5 kPa is reached.Install an adjustable valve (flapper) in the inlet air system atleast two pipe diameters befo

49、re any temperature, pressure, andhumidity measurement devices. Use the valve to maintain inletair restriction within required specifications.5Mack Service Manuals are available from local Mack Trucks, Inc. distributors.6Aeroquip lines are available at local hose distributors.D7156 1536.2.7 Fuel SupplyHeating, cooling, or both of the fuelsupply may be required. See Fig. A1.2, Annex A1, for arecommended system.6.2.8 Intake Manifold and Temperature ControlUse stain-less steel intake manifolds (P/N M10105GCX4332RSS forfront manifold, M10105GCX5212RSS for rear