ASTM D7156-2010a 4375 Standard Test Method for Evaluation of Diesel Engine Oils in the T-11 Exhaust Gas Recirculation Diesel Engine《评估T-11废气再循环柴油机中的柴油机油的标准试验方法》.pdf

《ASTM D7156-2010a 4375 Standard Test Method for Evaluation of Diesel Engine Oils in the T-11 Exhaust Gas Recirculation Diesel Engine《评估T-11废气再循环柴油机中的柴油机油的标准试验方法》.pdf》由会员分享，可在线阅读，更多相关《ASTM D7156-2010a 4375 Standard Test Method for Evaluation of Diesel Engine Oils in the T-11 Exhaust Gas Recirculation Diesel Engine《评估T-11废气再循环柴油机中的柴油机油的标准试验方法》.pdf（34页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D7156 10aStandard Test Method forEvaluation of Diesel Engine Oils in the T-11 Exhaust GasRecirculation Diesel Engine1This standard is issued under the fixed designation D7156; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revi

2、sion, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method covers an engine test procedure forevaluating diesel engine oils for performance ch

3、aracteristics ina diesel engine equipped with exhaust gas recirculation,including viscosity increase and soot concentrations (loading).2This test method is commonly referred to as the Mack T-11.31.1.1 This test method also provides the procedure forrunning an abbreviated length test, which is common

4、ly referredto as the T-11A. The procedures for the T-11A are identical tothe T-11 with the exception of the items specifically listed inAnnex A8. Additionally, the procedure modifications listed inAnnex A8 refer to the corresponding section of the T-11procedure.1.2 The values stated in SI units are

5、to be regarded asstandard. No other units of measurement are included in thisstandard.1.2.1 ExceptionsWhere there is no direct SI equivalentsuch as screw threads, National Pipe Threads/diameters, tubingsize, or where there is a sole source supply equipmentspecification.1.3 This standard does not pur

6、port to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use. See Annex A6 forspecific safety hazards.2. R

7、eferenced Documents2.1 ASTM Standards:4D86 Test Method for Distillation of Petroleum Products atAtmospheric PressureD93 Test Methods for Flash Point by Pensky-MartensClosed Cup TesterD97 Test Method for Pour Point of Petroleum ProductsD130 Test Method for Corrosiveness to Copper from Pe-troleum Prod

8、ucts by Copper Strip TestD235 Specification for Mineral Spirits (Petroleum Spirits)(Hydrocarbon Dry Cleaning Solvent)D287 Test Method forAPI Gravity of Crude Petroleum andPetroleum Products (Hydrometer Method)D445 Test Method for Kinematic Viscosity of Transparentand Opaque Liquids (and Calculation

9、of Dynamic Viscos-ity)D482 Test Method for Ash from Petroleum ProductsD524 Test Method for Ramsbottom Carbon Residue ofPetroleum ProductsD613 Test Method for Cetane Number of Diesel Fuel OilD664 Test Method for Acid Number of Petroleum Productsby Potentiometric TitrationD976 Test Method for Calculat

10、ed Cetane Index of DistillateFuelsD1319 Test Method for Hydrocarbon Types in LiquidPetroleum Products by Fluorescent Indicator AdsorptionD2274 Test Method for Oxidation Stability of DistillateFuel Oil (Accelerated Method)D2500 Test Method for Cloud Point of Petroleum ProductsD2622 Test Method for Su

11、lfur in Petroleum Products byWavelength Dispersive X-ray Fluorescence SpectrometryD2709 Test Method for Water and Sediment in MiddleDistillate Fuels by CentrifugeD3524 Test Method for Diesel Fuel Diluent in Used DieselEngine Oils by Gas Chromatography1This test method is under the jurisdiction of AS

12、TM Committee D02 onPetroleum Products and Lubricants and is the direct responsibility of SubcommitteeD02.B0 on Automotive Lubricants.Current edition approved Oct. 1, 2010. Published November 2010. Originallyapproved in 2005. Last previous edition approved in 2010 as D715610. DOI:10.1520/D7156-10A.2T

13、he ASTM Test Monitoring Center (TMC) will update changes in this testmethod by means of Information Letters. This edition includes all informationletters through 10-1. Information letters may be obtained from the ASTM TestMonitoring Center, 6555 Penn Ave., Pittsburgh, PA 15206-4489, Attention: Admin

14、-istrator.3ASTM International takes no position respecting the validity of any patentrights asserted in connection with any item mentioned in this standard. Users of thisstandard are expressly advised that determination of the validity of any such patentrights, and the risk of infringement of such r

15、ights, are entirely their ownresponsibility.4For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website1Copyright ASTM In

16、ternational, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.D4052 Test Method for Density, Relative Density, and APIGravity of Liquids by Digital Density MeterD4175 Terminology Relating to Petroleum, PetroleumProducts, and LubricantsD4294 Test Method for Sulfur i

17、n Petroleum and PetroleumProducts by Energy Dispersive X-ray Fluorescence Spec-trometryD4485 Specification for Performance of Engine OilsD4737 Test Method for Calculated Cetane Index by FourVariable EquationD4739 Test Method for Base Number Determination byPotentiometric Hydrochloric Acid TitrationD

18、5185 Test Method for Determination of Additive Ele-ments, Wear Metals, and Contaminants in Used Lubricat-ing Oils and Determination of Selected Elements in BaseOils by Inductively Coupled Plasma Atomic EmissionSpectrometry (ICP-AES)D5453 Test Method for Determination of Total Sulfur inLight Hydrocar

19、bons, Spark Ignition Engine Fuel, DieselEngine Fuel, and Engine Oil by Ultraviolet FluorescenceD5967 Test Method for Evaluation of Diesel Engine Oils inT-8 Diesel EngineD6278 Test Method for Shear Stability of Polymer Contain-ing Fluids Using a European Diesel Injector ApparatusD6896 Test Method for

20、 Determination of Yield Stress andApparent Viscosity of Used Engine Oils at Low Tempera-tureD7109 Test Method for Shear Stability of Polymer Contain-ing Fluids Using a European Diesel Injector Apparatus at30 and 90 CyclesD7422 Test Method for Evaluation of Diesel Engine Oils inT-12 Exhaust Gas Recir

21、culation Diesel EngineE29 Practice for Using Significant Digits in Test Data toDetermine Conformance with Specifications3. Terminology3.1 Definitions:3.1.1 blind reference oil, na reference oil, the identity ofwhich is unknown by the test facility.3.1.1.1 DiscussionThis is a coded reference oil that

22、 issubmitted by a source independent from the test facility.D41753.1.2 blowby, nin internal combustion engines, that por-tion of the combustion products and unburned air/fuel mixturethat leaks past piston rings into the engine crankcase duringoperation.3.1.3 calibrate, vto determine the indication o

23、r output ofa device (e.g., thermometer, manometer, engine) with respectto that of a standard.3.1.4 candidate oil, nan oil that is intended to have theperformance characteristics necessary to satisfy a specificationand is intended to be tested against that specification. D41753.1.5 exhaust gas recirc

24、ulation (EGR), nthe mixing ofexhaust gas with intake air to reduce the formation of nitrogenoxides (NOx). Automotive Handbook53.1.6 heavy-duty, adjin internal combustion engine op-eration, characterized by average speeds, power output andinternal temperatures that are close to the potential maximums

25、.D44853.1.7 heavy-duty engine, nin internal combustion enginetypes, one that is designed to allow operation continuously at orclose to its peak output.3.1.8 non-reference oil, nany oil other than a referenceoil; such as a research formulation, commercial oil, or candi-date oil. D41753.1.9 non-standa

26、rd test, na test that is not conducted inconformance with the requirements in the standard testmethod; such as running on an uncalibrated test stand, usingdifferent test equipment, applying different equipment assem-bly procedures, or using modified operating conditions.D41753.1.10 oxidation, nof en

27、gine oil, the reaction of the oilwith an electron acceptor, generally oxygen, that can producedeleterious acidic or resinous materials often manifested assludge formation, varnish formation, viscosity increase, orcorrosion, or combination thereof.3.1.11 reference oil, nan oil of known performance ch

28、ar-acteristics, used as a basis for comparison.3.1.11.1 DiscussionReference oils are used to calibratetesting facilities, to compare the performance of other oils, orto evaluate other materials (such as seals) that interact withoils. D41753.1.12 sludge, nin internal combustion engines, a deposit,pri

29、ncipally composed of insoluble resins and oxidation prod-ucts from fuel combustion and the lubricant, that does not drainfrom engine parts but can be removed by wiping with a cloth.D41753.1.13 standard test, na test on a calibrated test stand,using the prescribed equipment that is assembled in accor

30、dancewith the requirements in the test method, and conducted inaccordance with the specified operating conditions.3.1.14 varnish, nin internal combustion engines, a hard,dry, generally lustrous deposit that can be removed by solventsbut not by wiping with a cloth. D41753.1.15 wear, nthe loss of mate

31、rial from a surface, gener-ally occurring between two surfaces in relative motion, andresulting from mechanical or chemical action, or a combinationof both. D74224. Summary of Test Method4.1 The test operation involves use of a Mack E-TECHV-MAC III diesel engine with Exhaust Gas Recirculation(EGR).

32、Two oil flushes, each for 30 min, are followed by a testat constant speed and torque conditions for 252 h.4.2 Take oil samples periodically and analyze for viscosityincrease and soot content.4.3 Engine rebuilds may be necessary as indicated bydegradation of test parameters and are left to the discre

33、tion ofthe test laboratory. At rebuild, the power section of the engineis disassembled, solvent-cleaned, and rebuilt, using all newpistons, rings, cylinder liners, valves, and valve guides, in strictaccordance with furnished specification.4.4 Solvent-clean the engine crankcase and replace worn ordef

34、ective parts.5Available from Robert Bosch GmbH, Postfach 50, D-7000 Stuttgart 1,Germany.D7156 10a24.5 Equip the test stand with appropriate accessories forcontrolling speed, load, and various engine operating condi-tions.5. Significance and Use5.1 This test method was developed to evaluate the visco

35、sityincrease and soot concentration (loading) performance ofengine oils in turbocharged and intercooled four-cycle dieselengines equipped with EGR. Obtain results from used oilanalysis.5.2 The test method may be used for engine oil specificationacceptance when all details of the procedure are follow

36、ed.6. Apparatus6.1 General Description:6.1.1 The test engine is a Mack E-TECH V-MAC III,electronically controlled fuel injection with six electronic unitpumps, using 2002 cylinder heads (Annex A2). It is an open-chamber, in-line, six-cylinder, four-stroke, turbocharged,charge air-cooled, and compres

37、sion ignition engine. The boreand stroke are (124 by 165) mm, and the displacement is 12 L.6.1.2 The ambient laboratory atmosphere shall be relativelyfree of dirt and other contaminants as required by goodlaboratory standards. Filtering air, controlling temperature, andcontrolling humidity in the en

38、gine buildup area helps preventaccumulation of dirt and other contaminants on engine partsand aids in measuring and selecting parts for assembly.6.2 The Test Engine:6.2.1 Mack T-11 Test EngineThe engine and cylinderheads are available from Mack Trucks, Inc.6A complete partslist is shown in Table A2.

39、1, Annex A2. Use test parts on afirst-in/first-out basis.6.2.2 Engine Cooling System:6.2.2.1 Use a new Mack coolant conditioner shown in TableA2.1, Annex A2, every test, to limit scaling in the coolingsystem. At the expansion tank, pressurize the system to103 kPa. Use the coolant shown in 7.3.6.2.2.

40、2 Use a closed-loop, pressurized external engine cool-ing system composed of a nonferrous core heat exchanger,reservoir, and water-out temperature control valve. The systemshall prevent air entrainment and control jacket temperatureswithin the specified limit. Install a sight glass between theengine

41、 and the cooling tower to check for air entrainment anduniform flow in an effort to prevent localized boiling. Block thethermostat wide open.6.2.2.3 Flow the coolant from the engine block fitting to theEGR coolers, see Fig. A1.3, Annex A1. Return the EGRcoolant flow to the engine coolant-in line, ne

42、ar the coolantpump inlet, see Fig. A1.7, Annex A1.6.2.3 Auxiliary Oil System:6.2.3.1 To maintain a constant oil level in the pan, providean additional minimum volume sump of 11.4 L by using aseparate closed tank connected to the engine sump. Circulateoil through the system with an auxiliary pump. Th

43、e systemschematic is shown in Fig.A1.1,AnnexA1. The No. 6 and No.8 lines are to have inside diameters of 10 mm and 13 mm,respectively. Use a minimum No. 8 size vent line. Equivalentlines may be substituted forAeroquip7lines provided they havethe proper inside diameters.6.2.3.2 Locate the auxiliary o

44、il system suction line on theexhaust side of the oil pan, so that the inside bottom of theauxiliary oil system suction fitting is down from the oil pan railby 152 mm, and back from the front of the pan by 178 mm.Refer to Fig.A1.4,AnnexA1. Connect the auxiliary oil systemreturn line to the power stee

45、ring pump cover on the fronttiming gear cover. Refer to Fig. A1.5, Annex A1. Connect theauxiliary oil scale vent line to the top of the auxiliary oil sumpbucket and the dipstick tube opening.6.2.3.3 Use Viking Pump Model SG053514 as the auxiliaryoil pumps (see A2.10). Nominal pump speed is 1725 r/mi

46、n.Shut off the auxiliary oil pumps if the auxiliary oil system goesdry.6.2.3.4 Use a sight glass to aid in determining the oil levelshould the auxiliary oil system run dry. An example of a sightglass setup is shown in Fig. A1.18, Annex A1.6.2.4 Oil Cooling System:6.2.4.1 Use the oil cooler adapter b

47、locks to mount the oilcooler to the engine. The adapter blocks are available from thesupplier list in A2.7, Annex A2.6.2.4.2 Use the oil filter housing (part number 27GB525M)shown in Fig. A1.8, Annex A1.6.2.5 Blowby MeterUse a meter capable of providing dataat a minimum frequency of 6 min. To preven

48、t blowbycondensate from draining back into the engine, ensure theblowby line has a downward slope to a collection bucket.Ensure the collection bucket has a minimum volume of 18.9 L.Locate the blowby meter downstream of the collection bucket.The slope of the blowby line downstream of the collectionbu

49、cket is unspecified.6.2.6 Air Supply and FiltrationUse the Mack air filterelement and the Mack filter housing shown inA2.3,AnnexA2.Replace the filter cartridge when a DP of 2.5 kPa is reached.Install an adjustable valve (flapper) in the inlet air system atleast two pipe diameters before any temperature, pressure, andhumidity measurement devices. Use the valve to maintain inletair restriction within required specifications.6.2.7 Fuel SupplyHeating, cooling, or both of the fuelsupply may be required. See Fig. A1.2, Annex A1, for arecommended system.6.2.8 Intake Ma