ASTM D6957-2012 2500 Standard Practice for Measuring Curl in Paint Brush Filling Material《测量漆刷子填充材料卷曲度的标准实施规程》.pdf

《ASTM D6957-2012 2500 Standard Practice for Measuring Curl in Paint Brush Filling Material《测量漆刷子填充材料卷曲度的标准实施规程》.pdf》由会员分享，可在线阅读，更多相关《ASTM D6957-2012 2500 Standard Practice for Measuring Curl in Paint Brush Filling Material《测量漆刷子填充材料卷曲度的标准实施规程》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D6957 12Standard Practice forMeasuring Curl in Paint Brush Filling Material1This standard is issued under the fixed designation D6957; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number

2、 in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This practice describes the procedure for measuring curlin synthetic filament.1.2 This practice is applicable to filament 2 to 5 in. (50.8 to

3、127 mm) in length.1.3 This practice is applicable to tapered filament or levelfilament.1.4 This practice is applicable to loose filling material andmaterial removed from a brush.1.5 The values stated in inch-pound units are to be regardedas standard. The values given in parentheses are mathematicalc

4、onversions to SI units that are provided for information onlyand are not considered standard.1.6 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health prac

5、tices and determine the applica-bility of regulatory limitations prior to use.2. Terminology2.1 Definitions of Terms Specific to This Standard:2.1.1 paint brush filament, na synthetic polymer extrusionused in brushing material.2.1.2 filament curl, ndeviation from straight, along thelength of a filam

6、ent.2.1.3 butt-end, nthe larger end of a tapered filament;either end of a level filament.3. Significance and Use3.1 It is important for the manufacturing and performance ofa brush to have filaments with minimal curl.4. Apparatus4.1 Filament curl deviation chart. See Fig. 1.5. Procedure5.1 For Testin

7、g Synthetic Filaments:5.1.1 Select filaments to be measured.5.1.2 Allow filaments to acclimate to room temperature 70to 75F (21 to 24C) at least two hours.5.1.3 Place a filament on the filament curl deviation chartwith butt-end at the x-reference point (see Fig. 1).5.1.4 Record the degree of deviati

8、on from straight at theother end of the filament.5.1.5 If multiple filaments of the same type and length are tobe measured, repeat 5.1.3 and 5.1.4 for each of the remainingfilaments and average the results.6. Keywords6.1 curl; filament1This practice is under the jurisdiction of ASTM Committee D01 on

9、 Paint andRelated Coatings, Materials, and Applications and is the direct responsibility ofSubcommittee D01.61 on Paint Application Tools.Current edition approved June 1, 2012. Published July 2012. Originally approvedin 2003. Last previous edition approved in 2008 as D6957 08. DOI: 10.1520/D6957-12.

10、Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States1ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly adv

11、ised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either

12、 reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. I

13、f you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Indivi

14、dual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).FIG. 1 Filament Curl Deviation ChartD6957 122