ASTM D5241-1992(2011) Standard Practice for Micro-Extraction of Water for Analysis of Volatile and Semi-Volatile Organic Compounds in Water《水中挥发性和半挥发性有机化合物分析用水的微量萃取法的标准操作规程》.pdf

《ASTM D5241-1992(2011) Standard Practice for Micro-Extraction of Water for Analysis of Volatile and Semi-Volatile Organic Compounds in Water《水中挥发性和半挥发性有机化合物分析用水的微量萃取法的标准操作规程》.pdf》由会员分享，可在线阅读，更多相关《ASTM D5241-1992(2011) Standard Practice for Micro-Extraction of Water for Analysis of Volatile and Semi-Volatile Organic Compounds in Water《水中挥发性和半挥发性有机化合物分析用水的微量萃取法的标准操作规程》.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D5241 92 (Reapproved 2011)Standard Practice forMicro-Extraction of Water for Analysis of Volatile and Semi-Volatile Organic Compounds in Water1This standard is issued under the fixed designation D5241; the number immediately following the designation indicates the year oforiginal adopti

2、on or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This practice covers standard procedures for extractionof volatile and sem

3、i-volatile organic compounds from waterusing small volumes of solvents.1.2 The compounds of interest must have a greater solubil-ity in the organic solvent than the water phase.1.3 Not all of the solvents that can be used in microextraction are addressed in this practice. The applicability of asolve

4、nt to extract the compound(s) of interest must be demon-strated before use.1.4 This practice provides sample extracts suitable for anytechnique amenable to solvent injection such as gas chroma-tography or high performance liquid chromatography (HPLC).1.5 The values stated in SI units are to be regar

5、ded as thestandard.1.6 The values stated in SI units are to be regarded asstandard. No other units of measurement are included in thisstandard.1.7 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standar

6、d to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use. For specific hazardstatements, see Section 9.2. Referenced Documents2.1 ASTM Standards:2D1129 Terminology Relating to WaterD1193 Specification for Reagent WaterD3370 Pract

7、ices for Sampling Water from Closed ConduitsD3694 Practices for Preparation of Sample Containers andfor Preservation of Organic ConstituentsD3856 Guide for Good Laboratory Practices in Laborato-ries Engaged in Sampling and Analysis of WaterD3973 Test Method for Low-Molecular Weight Haloge-nated Hydr

8、ocarbons in Water3D4210 Practice for Intralaboratory Quality Control Proce-dures and a Discussion on Reporting Low-Level Data4D4448 Guide for Sampling Ground-Water MonitoringWellsD5175 Test Method for Organohalide Pesticides and Poly-chlorinated Biphenyls in Water by Microextraction andGas Chromatog

9、raphy3. Summary of Practice3.1 This practice employs liquid/liquid extraction to isolatecompounds of interest. The sample is added to an extractiondevice. The solvent may be added to the sample container or anextraction device and extracted for a period of 5 min. Thesolvent is then ready for analysi

10、s. If required, the pH may beadjusted and salt may be added prior to extraction to increasethe extraction specificity and efficiency.3.2 The solvent extract may be further processed usingsample clean-up and concentration techniques. The analytes inthe solvent may be analyzed using instrumental metho

11、ds forspecific volatile or semivolatile organic compounds. Thispractice does not include sample extract clean-up methods.4. Significance and Use4.1 This practice provides a general procedure for thesolvent extraction of volatile and semi-volatile organic com-pounds from a water matrix. Solvent extra

12、ction is used as theinitial step in the solvent extraction of organic constituents forthe purpose of quantifying extractable organic compounds.4.2 Typical detection limits that can be achieved usingmicro-extraction techniques with gas chromatography (GC)with flame ionization detector (FID), electron

13、 capture detector(ECD), or with a mass spectrometer (GC/MS) range frommilligrams per litre (mg/L) to nanograms per litre (ng/L). Thedetection limit, linear concentration range, and sensitivity ofthe test method for a specific organic compound will dependupon the sample clean-up, injection volume, so

14、lvent to sample1This practice is under the jurisdiction of ASTM Committee D19 on Water andis the direct responsibility of Subcommittee D19.06 on Methods for Analysis forOrganic Substances in Water.Current edition approved May 1, 2011. Published June 2011. Originallyapproved in 1992. Last previous ed

15、ition approved in 2004 as D5241 92 (2004).DOI: 10.1520/D5241-92R11.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM we

16、bsite.3Withdrawn4Withdrawn. The last approved version of this historical standard is referencedon www.astm.org.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.ratio, solvent concentration methods used, and the determina-tive techniqu

17、e employed.4.3 Micro-extraction has the advantage of speed, simpleextraction devices, and the use of small amounts of sample andsolvents.4.3.1 Selectivity can be improved by the choice of solvent(usually hexane or pentane) or mixed solvents, extraction timeand temperature, and ionic strength of the

18、solution.4.3.2 Extraction devices can vary from the sample containeritself to commercial devices specifically designed for micro-extraction. See 7.1 and 7.2.4.3.3 A list of chlorinated organic compounds that can bedetermined by this practice includes both high and low boilingcompounds or chemicals (

19、see Table 1).5. Interferences5.1 Solvents, reagents, glassware, and other sample process-ing hardware may yield discrete artifacts or elevated baselinesthat can cause poor precision and accuracy. See TerminologyD1129.5.1.1 Glassware should be washed with detergent, rinsedwith water, followed by a ri

20、nse with distilled in glass acetone.Final drying is done by air or 103C oven. Additional cleaningsteps may be required when the analysis requires levels ofmicrograms per litre or below. Once the glassware has beencleaned, it should be used immediately or stored wrapped inaluminum foil (shiny side ou

21、t) or by stretching a sheet ofPTFE-fluorocarbon over the top for storage.5.1.2 Plastics other than PTFE-fluorocarbon should beavoided. They are a significant source of interference and canadsorb some organics.5.1.3 A field blank prepared from water and carried throughsampling, subsequent storage, an

22、d handling can serve as acheck on sources of interferences from the containers.5.2 When performing analyses for specific organic com-pounds, matrix interferences may be caused by materials andconstituents that are coextracted from the sample. The extent ofsuch matrix interferences will vary consider

23、ably depending onthe sample and the specific instrumental analysis method used.Matrix interferences may be reduced by the choice of extract-ing solvent, or by using a clean-up technique on the extract.6. Selection of the Extraction Solvent6.1 The selection of solvent for extraction will depend uponm

24、any factors, including the following:6.1.1 Solvent compatibility with analytical instrumentation,6.1.2 Solubility of the organic constituent in the solventversus its solubility in water. The water/solvent ratio has beenfound to be critical to achieve optimum recovery of someanalytes (see Test Method

25、 D3973). Typical solvent to sampleratios are 1 to 10 or 20. The ratio should be optimized formaximum recovery or detection of an analyte, or both,6.1.3 The availability and purity of the solvent,6.1.4 The boiling point and viscosity of the solvent,6.1.5 The tendency of the solvent and matrix to form

26、emulsions, and6.1.6 Solubility of the solvent in the water.6.2 The analyst should analyze sample blank using thepotential solvent and demonstrate a recovery using a spikingprocedure in the matrix of interest before applying thisprocedure for sample analysis.7. Apparatus7.1 Volumetric Flasks, 110 mL.

27、57.2 Liquid/Liquid Extractor.67.3 Vials, auto sampler with septa and caps. Vials should becompatible with the automatic sample injector and should havean internal volume of not greater than 2 mL.7.4 Vial, crimper.7.5 Bottles, glass narrow mouth with TFE fluorocarbon-lined septum screw caps.7.6 Shake

28、r, wrist.8. Reagents8.1 Purity of WaterUnless otherwise indicated, referenceto water shall be understood to mean reagent water conformingto Type II of Specification D1193.8.2 Chromatographic grade solvents that have been distilledin glass should be used in all tests. Other grades may be used,if it i

29、s first ascertained that the solvent is of sufficiently highpurity to permit its use without lessening the accuracy of thedetermination.8.3 The extraction solvent of choice should be appropriatefor the matrix and compounds of interest. This choice isdependent upon the chemical properties of the orga

30、nic con-stituents of interest and the matrix being extracted.8.4 The spiking, standard materials and surrogates shouldbe reagent or ACS grade or better. When they are not availableas reagent grade, they should have an assay of 90 % or better.5Cassia, available from Baxter, 1430 Waukegan Rd., McGaw P

31、ark, IL 60085, orequivalent, has been found suitable for this purpose.6Available from J be careful not to include any of the waterphase. Preserve this second vial at 4C for an immediatereanalysis if necessary.12.7 If further extraction is required under different pHconditions (acid neutral or base),

32、 carefully remove the remain-ing solvent from the sample, adjust the pH, and add thenecessary fresh solvent volume. Repeat 12.4 and 12.5.12.8 Discard the contents of the sample bottle in an envi-ronmentally safe manner. Shake off the remaining few dropsusing short, brisk wrist movements, replace the

33、 cap, and weighthe empty bottle to the nearest 0.1 g.12.9 Analyze the extracts by the appropriate method(s) andcorrect the results for volume according to Section 13.13. Calculation13.1 Calculate the sample volume (Vs) in mL as equal to thenet sample weight in grams as follows:Vs5 grossweight 11.2!

34、2 tare weight 11.7!NOTE 6Brine samples will require a correction for density if highaccuracy is required. Samples with a high sediment content should becalculated based on weight to weight.13.2 Calculate the corrected sample concentration as fol-lows:13.2.1 When uncorrected analyte concentration is

35、known:C 5 CiX 1000Vswhere:C = concentration in g/L,Ci= uncorrected analyte concentration in g/mL, andVs= volume of the sample in mL.13.2.2 When only areas or peak heights are known:C 5 Sc3ArSr3ExVs3 1000where:C = concentration, in g/L,Sc= concentration of analyte in the standard, in g/mL,Ar= respons

36、e in area or peak height of the analyte in thesample,Sr= response in area or peak height of the standard for theanalyte to be determined,Ex= mL of extract, andVs= volume of sample extracted, in mL.14. Precision and Bias14.1 Precision and bias cannot be determined directly forthis practice. However,

37、this procedure was used in the deter-mination of organohalide pesticides, polychlorinated biphe-nyls, and chlorinated organics. See Test Method D5175.14.2 Precision and bias should be generated in the labora-tory on the parameters of concern.14.3 Precision may be improved by the use of an internalst

38、andard. Where internal standards are utilized, add the internalstandard to the extraction solvent container prior to aliquotingthe solvent to the extraction vessel.NOTE 7The results of one laboratory determining chlorinated organ-ics listed in Tables 1-3 are being included as information. A Cassiavo

39、lumetric flask containing 100 mLof acidified sample was extracted with1 mL of pentane solvent and analyzed using a gas chromatograph withflame ionization and electron capture detectors. The injection volume was1 L. Note that the bias information determined from the data will begreater than would be

40、expected from this practice. The standard was notprocessed through the entire practice, which would minimize the bias ofthe practice.15. Keywords15.1 extraction; microextraction; sample preparation; semi-volatile; volatile; waterTABLE 2 Recovery Data for Pentane Microextraction of 10 g/LSpiked Field

41、 SamplesNOTEBased on the Extraction of Six Spiked Water SolutionsAverage %Recovery% RelativeStandardDeviationTrichloroethene 69 4Tetrachloroethene 72 4Monochlorobenzene 82 3para-Chlorobenzotrifluoride 68 4ortho-Chlorobenzotrifluoride 76 4ortho-Chlorotoluene 88 4meta-Chlorotoluene 88 4para-Chlorotolu

42、ene 88 41,2,4-Trichlorobenzene 91 41,2,3-Trichlorobenzene 95 4Hexachlorobutadiene 78 41,2,4,5-Tetrachlorobenzene 94 4Hexachlorocyclopentadiene 84 42,4,5-Trichlorophenol 65 91,2,3,4-Tetrachlorobenzene 92 4alpha-Hexachlorocyclohexane 94 5beta-Hexachlorocyclohexane 87 5Hexachlorobenzene 94 6gamma-Hexac

43、hlorocyclohexane 96 4delta-Hexachlorocyclohexane 91 5D5241 92 (2011)4ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of an

44、y such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are i

45、nvited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not receiv

46、ed a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of

47、this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/)

48、.TABLE 3 Summary of Recovery Data for the PentaneMicroextraction of Spiked Field SamplesAAverage %Recovery% RelativeStandardDeviationTrichloroethene 71 6Tetrachloroethene 68 4Monochlorobenzene 85 3para-Chlorobenzotrifluoride 63 5ortho-Chlorobenzotrifluoride 74 2ortho-Chlorotoluene 88 2meta-Chlorotol

49、uene 90 4para-Chlorotoluene 89 21,2,4-Trichlorobenzene 89 51,2,3-Trichlorobenzene 93 5Hexachlorobutadiene 64 161,2,4,5-Tetrachlorobenzene 93 4Hexachlorocyclopentadiene 75 102,4,5-Trichlorophenol 60 61,2,3,4-Tetrachlorobenzene 91 5alpha-Hexachlorocyclohexane 95 2beta-Hexachlorocyclohexane 86 2Hexachlorobenzene 95 2gamma-Hexachlorocyclohexane 97 2delta-Hexachlorocyclohexane 90 3AAverage of five replicate spiked water solutions each at 20, 50, and 100 g/Land six replicate spiked water solutions at 10 g/L.D5241 92 (2011)5