ASTM D1327-2004 Standard Specification for Bitumen-Saturated Woven Burlap Fabrics Used in Roofing and Waterproofing《铺屋面和防水用浸沥青机织粗麻布织物的标准规范》.pdf

《ASTM D1327-2004 Standard Specification for Bitumen-Saturated Woven Burlap Fabrics Used in Roofing and Waterproofing《铺屋面和防水用浸沥青机织粗麻布织物的标准规范》.pdf》由会员分享，可在线阅读，更多相关《ASTM D1327-2004 Standard Specification for Bitumen-Saturated Woven Burlap Fabrics Used in Roofing and Waterproofing《铺屋面和防水用浸沥青机织粗麻布织物的标准规范》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D 1327 04Standard Specification forBitumen-Saturated Woven Burlap Fabrics Used in Roofingand Waterproofing1This standard is issued under the fixed designation D 1327; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the

2、 year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1. Scope1.1 This specification covers w

3、oven burlap fabrics, satu-rated with either asphalt or refined coal-tar, as specified by thepurchaser, for use in the membrane system of roofing orwaterproofing or as specified by the manufacturer.1.1.1 Asphalt-saturated burlap fabric shall be used withasphalt base plying cement; typical ones are mo

4、pping asphaltsconforming to Specifications D 312, D 449, or appropriatesolvent-bearing bituminous materials.1.1.2 Coal-tar-saturated burlap fabric shall be used withcoal-tar base plying cements; typical ones are coal-tar pitchesconforming to Specification D 450, or appropriate solvent-bearing bitumi

5、nous materials.1.2 The values stated in SI units are to be regarded as thestandard. The values given in parentheses are for informationonly.2. Referenced Documents2.1 ASTM Standards:2D 146 Test Methods for Sampling and Testing Bitumen-Saturated Felts and Woven Fabrics for Roofing and Wa-terproofingD

6、 312 Specification for Asphalt Used in RoofingD 449 Specification for Asphalt Used in Dampproofing andWaterproofingD 450 Specification for Coal-Tar Pitch Used in Roofing,Dampproofing, and WaterproofingD 1079 Terminology Relating to Roofing, Waterproofing,and Bituminous Materials2.2 AATCC Standard:Me

7、thod 30-1974 Test for Resistance of Textiles to Mildewand Rot33. Terminology3.1 DefinitionsFor definitions of terms used in this speci-fication, refer to Terminology D 1079.4. Materials and Manufacture4.1 The fabric to be saturated shall be composed of 100 %jute fiber except for two cotton threads i

8、n each selvage. If theselvage is used, it shall be no more than 6 mm (14 in.) wide.The minimum fabric construction used shall be 180 g/m2(5.4oz/yd2) minimum burlap.4.2 In the process of manufacture, the dry burlap fabric shallbe saturated with bitumen.5. Physical Properties5.1 The material shall con

9、form to the physical propertiesprescribed in Table 1.5.2 The rolls shall not crack nor be so sticky as to causetearing or material damage upon being unrolled at temperaturesbetween 10 and 60C (50 and 140F).5.3 Resistance to RottingThe average percentage of theoriginal strength retained by the satura

10、ted product shall be atleast 1.75 times that retained by the control sample after oneweek.6. Workmanship, Finish, and Appearance6.1 The burlap fabric shall be thoroughly and uniformlysaturated in such a manner that every fiber shall be visiblystained through by the saturant.6.2 The meshes of the fab

11、ric shall not be completely closedor sealed by the process of saturation. There shall be sufficientporosity maintained to allow successive moppings of theplying cement to seep through.1This specification is under the jurisdiction of ASTM Committee D08 onRoofing and Waterproofing and is the direct re

12、sponsibility of Subcommittee D08.04on Felts and Fabrics.Current edition approved Jan. 1, 2004. Published January 2004. Originallyapproved in 1954. Last previous edition approved in 1997 as D 1327 97a.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Servic

13、e at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Available from American Association of Textile Chemists and Colorists(AATCC), One Davis Dr., P.O. Box 12215, Research Triangle Park, NC 27709-2215.1Copyright AS

14、TM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.6.3 The surface of the fabric shall not be coated or coveredwith talc or any other substances that would tend to interferewith the adhesion between the fabric and the plying cement.6.4 The surface s

15、hall be uniformly smooth and free ofirregularities, folds, and knots.6.5 The finished material shall be free of visible externaldefects, such as ragged or untrue edges, breaks, rents, orcracks.7. Sampling and Test Methods7.1 Sample the material and determine the properties enu-merated in this specif

16、ication in accordance with Test MethodsD 146.7.2 Determine resistance to rotting by the soil burial methoddescribed in Test 1 of AATCC Test Method 30-1974, modifiedas follows:7.2.1 The control sample shall consist of at least fivespecimens of 238 g/m2(7-oz/1 yd2) untreated Osnaburg con-taining not m

17、ore than 8 % sizing.7.2.2 Place each control specimen in the soil between twospecimens of the warp and two specimens of the filling of thesaturated fabric, all parallel to each other and approximately 25mm (1 in.) apart. Remove all specimens for testing after oneweek.7.2.3 The soil shall be sufficie

18、ntly active to decrease thestrength of the Osnaburg at the end of the week to 25 % or lessof its original strength; if not, repeat the exposure with freshsoil and fresh specimens.8. Inspection8.1 InspectionInspection shall be in accordance with therequirements of this specification.8.2 Inspection Al

19、ternativesAlternative inspection require-ments shall be determined by and as agreed upon between thepurchaser and the supplier.9. Rejection and Resubmittal9.1 Failure to ConformFailure to conform to any of therequirements as stated in this specification constitutes groundsfor rejection.9.2 Rejection

20、 RedressThe supplier shall have the right toinspect the rejected materials. The supplier and the purchasershall agree to the quantity of rolls deemed unacceptable. Thesupplier shall then have the right to submit the same number ofnew rolls as replacement.10. Packaging and Package Marking10.1 Unless

21、otherwise agreed upon between the supplierand purchaser, each product package shall be plainly markedwith the suppliers name, the product brand, the ASTMdesignation, and type of bitumen if not evident in the labelname of the product.10.2 The rolls shall be securely wrapped or banded in amanner that

22、completely encircles the roll and will preventslipping or unrolling.10.3 The rolls of saturated burlap fabric shall be wound onmandrels or rigid hollow fiber cylinders not less than 50 mm (2in.) in diameter, extending not more than 100 mm (4 in.)beyond the ends of the rolls.10.4 No roll shall contai

23、n more than two pieces, and nomore than 3 % of the rolls in any lot shall contain two pieces.If a roll contains a manufacturing splice, the splice shall beclearly marked.11. Keywords11.1 asphalt or coal tar saturated; roofing; waterproofing;woven burlap fabricTABLE 1 Physical Properties of Bitumen-S

24、aturated Woven Burlap FabricMin MaxGross mass per roll, kg (lb) 15.8 (34.8) 27.2 (60.0)Mass of wrapping material and mandrel, kg (lb) . 1.13 (2.5)Width of roll, mm (in.) 890 (35) 1040 (41)Width of selvage, mm (in.) . 6.5 (0.25)Average net mass per unit area, g/m2(oz/yd2) 330 (9.8) .Detached comminut

25、ed surfacing, g/m2(lb/100 ft2) . 50 (1.0)Moisture max, mass % . 6.0AAverage breaking strength at 21.1C (70F):Lengthwise (warp direction), kN/m (lbf/in.) 8.8 (50) .Crosswise (fill direction), kN/m (lbf/in.) 8.8 (50) .Pliability at 0C (32F) no cracking .Mass of desaturated (unsaturated) fabric, g/m2(o

26、z/yd2)B180 (5.3)C.Mass of saturant, g/m2(lb/100 ft2)B0.7 3 (mass of desaturated moisture-freefabric in same area).Thread count per 25.4 mm (in.), both directionsD9 (9) .Ash, %D. 2.0AAt time of manufacture. Products with higher moisture content at time of installation may cause hot materials to foam,

27、 creating interply voids that may result in blisters.BIn the case of coal-tar-saturated fabric, this value shall be the moisture-free fabric prior to saturation. Coal-tar-saturated fabric cannot be thoroughly desaturated byany known means; only an approximate value may be obtained through desaturati

28、on.CNominal 212.6 g (712-oz) burlap weighs approximately 230 g/m2(634 oz/yd2). The minimum requirement allows for a 5 % tolerance in mass on the low side, and alsoassumes a max 7 % oil content and 12 % moisture regain, both of which are extracted in the desaturating process.DOn desaturated fabrics i

29、n the case of coal-tar-saturated fabric, this property shall be determined on the fabric prior to saturation.D1327042ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly

30、advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, eit

31、her reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend

32、. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).D1327043