ASTM C754-2009a Standard Specification for Installation of Steel Framing Members to Receive Screw-Attached Gypsum Panel Products《用螺钉安装石膏墙板的钢框构件安装的标准规范》.pdf

《ASTM C754-2009a Standard Specification for Installation of Steel Framing Members to Receive Screw-Attached Gypsum Panel Products《用螺钉安装石膏墙板的钢框构件安装的标准规范》.pdf》由会员分享，可在线阅读，更多相关《ASTM C754-2009a Standard Specification for Installation of Steel Framing Members to Receive Screw-Attached Gypsum Panel Products《用螺钉安装石膏墙板的钢框构件安装的标准规范》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: C754 09aStandard Specification forInstallation of Steel Framing Members to Receive Screw-Attached Gypsum Panel Products1This standard is issued under the fixed designation C754; the number immediately following the designation indicates the year oforiginal adoption or, in the case of re

2、vision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1. Scope*1.1 This specificati

3、on covers the minimum requirements forthe installation of interior nonstructural steel framing andfurring members designed to receive screw-attached gypsumpanel products. The steel framing and furring members cov-ered in this specification are limited to those complying withSpecification C645.1.2 De

4、tails of construction for a specific assembly toachieve the required fire resistance, sound or acoustic ratingshall be obtained from reports of fire-resistance tests, engineer-ing evaluations, or listings from recognized fire testing, soundor acoustic laboratories.1.3 The values stated in inch-pound

5、 units are to be regardedas standard. The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.2. Referenced Documents2.1 ASTM Standards:2A641/A641M Specification for ZincCoated (Galvanized)Carbon Steel WireA653/A65

6、3M Specification for Steel Sheet, Zinc-Coated(Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed)by the Hot-Dip ProcessA1008/A1008M Specification for Steel, Sheet, Cold-Rolled, Carbon, Structural, High-Strength Low-Alloy,High-Strength Low-Alloy with Improved Formability, So-lution Hardened, and Bak

7、e HardenableC11 Terminology Relating to Gypsum and Related BuildingMaterials and SystemsC645 Specification for Nonstructural Steel Framing Mem-bersC840 Specification for Application and Finishing of Gyp-sum Board2.2 ICC-ES Document3ICC-ES-AC86 Acceptance Criteria for Steel Studs andGypsum-Board Inte

8、rior Nonload-Bearing WallsComplete ConstructionAC86Approved July 1995(Editorially revised September 2005) (Formerly ICBOAC86 dated July 1995)3. Terminology3.1 DefinitionsTerms shall be as defined in TerminologyC11.3.2 Descriptions of Terms Specific to This Standard:3.2.1 channel, nthe material descr

9、ibed in 4.3 to whichfurring members are attached.3.2.2 cross furring, nfurring member attached perpen-dicular to main runners or framing members.3.2.3 cross furring member, na member installed perpen-dicularly to the main beams designed to receive screw attachedgypsum panel products.3.2.4 direct fur

10、ring, nfurring members attached directlyto the structural members of the building.3.2.5 framing member, nmetal studs, runners (track), andrigid furring channels designed to receive screw attachedgypsum panel products.3.2.6 furred ceiling, na ceiling in which the rigid furringchannels and studs are a

11、ttached directly to the structuralmembers of the building.3.2.7 furring, vpreparing a wall or ceiling with framing orfurring members to provide a level surface or airspace.3.2.8 furring member, nmetal studs, rigid furring chan-nels, or channels used either as direct furring or as crossfurring.3.2.9

12、grid suspension system, na ceiling system com-posed of modular interlocking steel components designed toreceive screw-attached gypsum panel products.1This specification is under the jurisdiction of ASTM Committee C11 onGypsum and Related Building Materials and Systems and is the direct responsibilit

13、yof Subcommittee C11.03 on Specifications for theApplication of Gypsum and OtherProducts in Assemblies.Current edition approved Nov. 1, 2009. Published December 2009. Originallyapproved in 1974. Last previous edition approved in 2009 as C754 09. DOI:10.1520/C0754-09a.2For referenced ASTM standards,

14、visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Available from ICC Evaluation Services, Inc., 5360 Workman Mill Road,Whittier, CA 90601, www

15、.icc-es.org.1*A Summary of Changes section appears at the end of this standard.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.3.2.10 main beam, nthe main support member of a gridsuspension system that receives cross furring members.3

16、.2.11 main runner, nthe channel or stud that is attachedto or suspended from the structural members of the building.3.2.12 runner (track), na member designed to receive theends of metal studs, attached directly to the structural membersof the building.3.2.13 suspended ceiling, na ceiling in which th

17、e mainrunners and cross furring are suspended below the structuralmembers of the building.4. Materials and Manufacture4.1 Studs, Runners, Rigid Furring Channels, and GridSuspension Systemssee Specification C645.4.2 Tie Wire and Hanger WireZinc-coated (galvanized)soft-annealed steel, or of a material

18、 and size having equivalentcorrosion resistance and strength. Wire diameters (uncoated)specified herein correspond with United States steel wire gaugenumbers as follows:DiameterAWire Gauge(U.S. Steel Wire Gauge)in. mm0.0348 0.88 No. 200.0410 1.04 No. 190.0475 1.21 No. 180.0540 1.37 No. 170.0625 1.59

19、 No. 160.0800 2.03 No. 140.0915 2.32 No. 130.1055 2.68 No. 120.1205 3.06 No. 110.1350 3.43 No. 100.1483 3.77 No. 90.1620 4.12 No. 8AAllowable variations in diameter shall be in accordance with tolerances asestablished in Specification A641/A641M.4.3 ChannelsChannels shall be cold-formed from steelwi

20、th a minimum 33 000 psi (228 MPa) yield strength and0.0538 in. (1.37 mm) minimum bare steel thickness. Channelsshall have a protective coating conforming to SpecificationA653/A653MG40 or shall have a protective coating with anequivalent corrosion resistance, and shall have the followingminimum weigh

21、ts in lb per 1000 linear ft (kg/m):Size Weight Flange Widthin. (mm) lb/1000 ft (kg/m) in. (mm)34 (19) 277 (0.412)12 (13)112 (38) 414 (0.616)12 (13)2 (51) 506 (0.753)12 (13)212 (64) 597 (0.888)12 (13)4.4 Grid Suspension System:4.4.1 Main BeamFormed from cold-rolled steel “T” sec-tions, indexed with s

22、lots to receive ends of cross furringmembers, and with stamped couplings at each end for thepurpose of splicing.4.4.2 Cross Furring MembersFormed from cold-rolledsteel, designed to permit screw attachment of gypsum panelproducts, and formed with an end configuration that permitsmechanical interlock

23、with the indexed slots of the main beam.4.5 Rod and Flat HangersFormed from steel conformingto Specification A1008/A1008M. When specified, rod and flathangers shall be protected with zinc coating or another equallyrust-inhibiting coating.5. Installation of Metal Framing5.1 Tolerances:5.1.1 Spacing o

24、f studs and furring members shall be notmore than 618 in. (3 mm) from the spacing shown in Tables 1and 2. Any cumulative error shall be not more than 618 in.5.2 Runner (Track) Installation:5.2.1 GeneralRunners shall be aligned accurately at thefloor and ceiling and securely anchored approximately 2

25、in. (50mm) from the runner ends, not more than 24 in. (610 mm) oncenter. Runners shall be secured with fasteners at partitioncorners. One runner shall extend to the end of the corner andthe other runner shall butt to it and be gapped to allowclearance for the gypsum panel product thickness. Runnerss

26、hall not be mitered.5.2.2 Runners to Concrete SlabsShall be fastened withconcrete stub nails, expansion anchors, shielded screws, orpower-driven fasteners not exceeding 24 in. (610 mm) oncenter.5.2.3 Runners to WoodShall be fastened with screwsproviding not less than 1 in. (25 mm) penetration or nai

27、lsproviding 112 in. (38 mm) penetration into the wood.5.2.4 Runners to Suspended CeilingsShall be fastenedwith “Molly”-type expandable fasteners, toggle bolts, clamps,or screws into channels, splines, “T” runners, or other mem-bers.5.3 Stud Installation:5.3.1 Stud Height and Spacing Limitations:5.3.

28、1.1 Maximum framing spacing determined by gypsumpanel product thickness shall be in accordance with Table 1.5.3.1.2 Stud heights shall be not greater than those shown inTables 3-5.5.3.1.3 Studs shall engage both the floor and ceiling run-ners. The gap between the end of a stud and the web of the top

29、and bottom runner shall be not more than14 in. (6 mm).5.3.1.4 Where conditions require that a partition be con-structed with compensation for vertical structural movement,the gap between the end of a stud and the adjacent runner shallbe designed by an architect or engineer.5.3.2 Location:5.3.2.1 Stu

30、ds shall be positioned vertically and shall bespaced not more than the maximum framing spacing allowedfor the finish specified. Studs located adjacent to door andwindow frames, partition intersections, and corners shall beanchored to runner flanges by screws, or by crimping at eachstud and runner fl

31、ange.5.3.2.2 At the junction of through and abutting partitions, astud shall be located not more than 2 in. (50 mm) away fromthe intersection in the abutting partition from the throughpartition (see Fig. 1), and not more than 2 in. (50 mm) frompartition corners and other construction.Astud shall be

32、locatedadjacent to all door and borrowed light frames. Studs shall besecurely anchored to the jamb anchor clips on each door frameor borrowed light frame by bolt or screw attachment. A headershall be formed over metal door and borrowed light frameswith a cut-to-length section of runner placed horizo

33、ntally withthe flanges cut and web bent vertically at each end, andsecurely attached to the adjacent vertical studs. A cut-to-lengthstud shall be positioned at the location of vertical joints overC754 09a2the header extending to the ceiling runner. Additional cut tolength studs required to comply wi

34、th framing spacing inaccordance with Table 1 shall also be added over the header,extending to the ceiling runner.5.3.2.3 At partition corners, a stud shall be installed so thatit forms the outside corner. Following application of a singlelayer of gypsum panel product to this stud, a second stud shal

35、lbe installed in the abutting runner and the web shall be screwattached through the gypsum panel product into the flange ofthe first stud (see Fig. 2).Athree-stud conventional corner shallbe permitted (see Fig. 3).5.4 Chase Wall Partitions:5.4.1 A double row of runners and studs as specified in 5.2a

36、nd 5.3 shall be installed. Height shall be in accordance with5.3.1.2.5.4.2 Where a gypsum panel product is used as bracingbetween chase walls, a gap of not more than 20 in. (508 mm)between rows of studs shall be permitted.5.4.3 Horizontal cross braces to opposite studs shall beinstalled not more tha

37、n 4 ft (1220 mm) on center vertically.Horizontal cross braces shall be either of the following:5.4.3.1 Gypsum panel product gussets 12 in. (305 mm) deepattached to the stud webs with three screws.5.4.3.2 A stud or runner with the web screw attached to thewall stud web with not less than two screws.5

38、.5 Rigid Furring Channel Installation, Direct Attachmentto Masonry or ConcreteThe furring member shall be at-tached to masonry or concrete surfaces, either vertically orhorizontally. Spacing shall be determined by gypsum panelproduct thickness in accordance with Table 1. For furringpositioned horizo

39、ntally, the center line of the furring membersclosest to the floor and ceiling shall be attached not more than3 in. (76 mm) from the floor and ceiling lines. The furringmember shall be secured with fasteners occurring on alternatedflanges and spaced 24 in. (610 mm) on center.5.6 Resilient Furring Ch

40、annel Installation to Steel andWood Members:TABLE 1 Maximum Framing SpacingNOTE 1Where a conflict exists in spacing between base and face layers, the closer spacing shall govern.Gypsum Panel Product ThicknessLocation ApplicationMaximum Spacing, ocBase Layer,in. (mm)Face Layer,in. (mm)One Layer Only,

41、in. (mm)Two LayersFasteners Only,in. (mm)Adhesive BetweenLayers, in. (mm)38 (9.5) . . . ceilings perpendicular 16 (406)A16 (406)A16 (406)A38 (9.5) ceilings perpendicular NA 16 (406) 16 (406)38 (9.5) ceilings parallel NA NR 16 (406)12 (12.7) . . . ceilings perpendicular 24 (610)A24 (610)A24 (610)A. .

42、 . ceilings parallel 16 (406)A16 (406)A16 (406)A38 (9.5) ceilings perpendicular NA 16 (406) 24 (610)38 (9.5) ceilings parallel NA NR 24 (610)12 (12.7) ceilings perpendicular NA 24 (610) 24 (610)12 (12.7) ceilings parallel NA 16 (406) 24 (610)58 (15.9) . . . ceilings perpendicular 24 (610)A24 (610)A2

43、4 (610)A. . . ceilings parallel 16 (406)A16 (406)A16 (406)A38 (9.5) ceilings perpendicular NA 16 (406) 24 (406)38 (9.5) ceilings parallel NA NR 24 (610)12 or58 (12.7 or 15.9) ceilings perpendicular NA 24 (610) 24 (610)12 or58 (12.7 or 15.9) ceilings parallel NA 16 (406) 24 (406)14 (6.4) . . . walls

44、parallel NR 16 (406)A16 (406)A38 (9.5) walls NR NR NR NR12 or58 (12.7 or 15.9) walls perpendicular or parallel NA 16 (406) 16 (406)38 (9.5) . . . walls perpendicular or parallel 16 (406)A16 (406)A24 (610)A38 or12 or58 (9.5 or12.7 or 15.9)walls perpendicular or parallel NA 16 (406) 24 (610)12 or58 (1

45、2.7 or15.9). . . walls perpendicular or parallel 24 (610)A24 (610)A24 (610)A38 or12 or58 (9.5 or12.7 or 15.9)walls perpendicular or parallel NA 24 (610) 24 (610)Perpendicularperpendicular to framing membersParallelparallel to framing membersNAnot applicableNRnot recommendedocon centerADenotes framin

46、g spacing for base layer in two-layer application.TABLE 2 Spans and Spacings of Horizontal Furring MembersType of FurringMaximumASpacingctoc,Bin. (mm)Maximum Span,ft (mm)Rigid Furring Channel 24 (610) 4 (1220)158 in. (41 mm) stud(erected withopen side up and againstsupport)24 (610) 5 (1520)212 in. (

47、64 mm) stud(erected withweb vertical to support)C24 (610) 6 (1830)358 in. (92 mm) stud(erected withweb vertical to support)C24 (610) 8 (2440)AConsult Table 1 for maximum spacing as determined by gypsum panel productthickness.Bc to ccenter to centerCA6 in. (150 mm) length of same size stud or track s

48、hall be nested to form a“box” at each saddle tie.C754 09a35.6.1 Resilient furring channel shall be installed to wallframing members with the mounting flange of the resilientfurring channel down, except at the floor where the attachmentflange shall be permitted to be installed with the flange up toac

49、commodate fastening to the framing members (See Fig. 4).In the case of two-legged resilient furring channel only thelower attachment flange shall be attached the the wall framingmembers.5.6.2 For wall framing members, the first (lowest) row ofresilient furring channel shall be not more than 2 in. (50 mm)off of the floor (as measured from the floor to the center of theface of the resilient channel) and the highest row of resilientfurring channel shall be not more than 6 in. (150 mm) from theceiling (as m