ANSI ASME A112.6.2-2017 Framing-Affixed Supports (Carriers) for Off-the-Floor Plumbing Fixtures.pdf

《ANSI ASME A112.6.2-2017 Framing-Affixed Supports (Carriers) for Off-the-Floor Plumbing Fixtures.pdf》由会员分享，可在线阅读，更多相关《ANSI ASME A112.6.2-2017 Framing-Affixed Supports (Carriers) for Off-the-Floor Plumbing Fixtures.pdf（17页珍藏版）》请在麦多课文档分享上搜索。

1、AN AMERICAN NATIONAL STANDARDASME A112.6.2-2017Revision of ASME A112.6.2-2000 (R2010)Framing-Affixed Supports (Carriers) for Off-the-Floor Plumbing FixturesASME A112.6.2-2017Revision of ASME A112.6.2-2000 (R2010)Framing-AffixedSupports (Carriers) forOff-the-FloorPlumbing FixturesxAN AMERICAN NATIONA

2、L STANDARDxDate of Issuance: December 19, 2017This Standard will be revised when the Society approves the issuance of a new edition.ASME issues written replies to inquiries concerning interpretations of technical aspects of this Standard. Interpretations arepublished on the Committee Web page and un

3、der http:/go.asme.org/InterpsDatabase. Periodically certain actions of theASMEA112CommitteemaybepublishedasCases.CasesarepublishedontheASMEWebsiteundertheA112CommitteePageat http:/go.asme.org/A112committee as they are issued.Errata to codes and standards may be posted on the ASME Web site under the

4、Committee Pages to provide corrections toincorrectlypublisheditems,ortocorrecttypographicalorgrammaticalerrorsincodesandstandards.Sucherratashallbeusedon the date posted.The A112 Committee Page can be found at http:/go.asme.org/A112committee. There is an option available to automaticallyreceive an e

5、-mail notification when errata are posted to a particular code or standard. This option can be found on theappropriate Committee Page after selecting “Errata” in the “Publication Information” section.ASME is the registered trademark of The American Society of Mechanical Engineers.Thiscodeorstandardw

6、asdevelopedunderproceduresaccreditedasmeetingthecriteriaforAmericanNationalStandards.TheStandardsCommitteethatapprovedthecodeorstandardwasbalancedtoassurethatindividualsfromcompetentandconcernedinterestshavehadanopportunity to participate.The proposed code orstandardwas made available for public rev

7、iew and commentthat provides an opportunityfor additional public input from industry, academia, regulatory agencies, and the public-at-large.ASME does not “approve,” “rate,” or “endorse” any item, construction, proprietary device, or activity.ASME does not take any position with respect to the valid

8、ity of any patent rights asserted in connection with any items mentioned in thisdocument,anddoesnotundertaketoinsureanyoneutilizingastandardagainstliabilityforinfringementofanyapplicableletterspatent,norassumeanysuchliability.Usersofacodeorstandardareexpresslyadvisedthatdeterminationofthevalidityofa

9、nysuchpatentrights,andtherisk of infringement of such rights, is entirely their own responsibility.Participation by federal agency representative(s) or person(s) affiliated with industry is not to be interpreted as government or industryendorsement of this code or standard.ASME accepts responsibilit

10、y for only those interpretations of this document issued in accordance with the established ASME proceduresand policies, which precludes the issuance of interpretations by individuals.No part of this document may be reproduced in any form,in an electronic retrieval system or otherwise,without the pr

11、ior written permission of the publisher.The American Society of Mechanical EngineersTwo Park Avenue, New York, NY 10016-5990Copyright 2017 byTHE AMERICAN SOCIETY OF MECHANICAL ENGINEERSAll rights reservedPrinted in U.S.A.CONTENTSForeword . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

12、. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ivCommittee Roster . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vCorrespondence With the A112 Committee . . . . . . . . . . . . . .

13、 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

14、. . . . . . . . . . . . . . . . . . . . . . . . 13 Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Test Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

15、 . . . . . . . 35 Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Figures1 Combination Carrier and Fittings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Load Tes

16、t on Off-the-Floor Plumbing Fixtures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3iiiFOREWORDIn1990,TheAmericanSocietyofMechanicalEngineers(ASME)wassolicitedtodevelopastandardforcarriersthatareusedinframeconstruction.Atthetime,astandardexistedfortheevaluationoffloor-aff

17、ixedcarriersandsupportsthataretypically installed in commercial, industrial, and institutional buildings with concrete floors. The standard for floor-affixed carriers and supports is ASME A112.6.1M.This Standard complements ASME A112.6.1M. Some of the specifications and tests are similar and appropr

18、iatelyreferenced in this Standard. However, due to differences in assembly of these framing-affixed products from thefloor-affixed products, some criteria are different.The basis for this Standard was an Interim Guide Criteria document prepared by the International Association ofPlumbing and Mechani

19、cal Officials (IAPMO).ASME A112.6.2-2017 was approved as an American National Standard on November 1, 2017.ivASME A112 COMMITTEEStandardization of Plumbing Materials and Equipment(The following is the roster of the Committee at the time of approval of this Standard.)STANDARDS COMMITTEE OFFICERSW. M.

20、 Smith, ChairS. Rawalpindiwala, Vice ChairA. L. Guzman Rodriguez, SecretarySTANDARDS COMMITTEE PERSONNELR. K. Adler, City of San JoseJ. A. Ballanco, JB Engineering and Code ConsultingJ. E. Bertrand, Moen, Inc.A. Bonlender, Bradley Corp.R. Burnham, Zurn Industries, LLCM. Campos, ICC Evaluation Servic

21、e, LLCW. E. Chapin, Professional Code Consulting, LLCA. Ciechanowski, NSF InternationalP. V. DeMarco, IAPMON. E. Dickey, CSA GroupG. S. Duren, Code Compliance, Inc.R. Emmerson, ConsultantR. L. George, Plumb-Tech Design and Consulting Services, LLCA. L. Guzman Rodriguez, The American Society of Mecha

22、nicalEngineersG. W. Harrison, ConsultantL. M. Himmelblau, Chicago Faucet Co.J. M. Koeller, Koeller and Co.C. J. Lagan, American StandardJ. W. Lauer, Sloan Valve Co.W. Levan, Cast Iron Soil Pipe InstituteD. Marbry, Fluidmaster, Inc.R. Mata, CSA GroupD. Orton, NSF InternationalS. Rawalpindiwala, Kohle

23、r Co.S. A. Remedios, Remedios Consulting, LLCM. Sigler, Plumbing Manufacturers InternationalG. L. Simmons, Charlotte Pipe and FoundryW. M. Smith, American Society of Plumbing EngineersD. Viola, IAPMOJ. C. Watson, Elkay ManufacturingM. Weiss, Plumbing however,theyshouldnotcontainproprietarynamesorinf

24、ormation.RequeststhatarenotintheformatdescribedabovemayberewrittenintheappropriateformatbytheCommitteepriorto being answered, which may inadvertently change the intent of the original request.viMoreover, ASME does not act as a consultant for specific engineering problems or for the general applicati

25、on orunderstanding of the Standard requirements. If, based on the inquiry information submitted, it is the opinion ofthe Committee that the Inquirer should seek assistance, the inquiry will be returned with the recommendationthat such assistance be obtained.ASMEproceduresprovideforreconsiderationofa

26、nyinterpretationwhenorifadditionalinformationthatmightaffectan interpretation is available. Further, persons aggrieved by an interpretation may appeal to the cognizant ASMECommitteeorSubcommittee.ASMEdoesnot“approve,”“certify,”“rate,”or“endorse”anyitem,construction,proprietarydevice, or activity.Att

27、endingCommitteeMeetings. TheA112StandardsCommitteeregularlyholdsmeetingsand/ortelephoneconfer-encesthatareopentothepublic.Personswishingtoattendanymeetingand/ortelephoneconferenceshouldcontacttheSecretary of the A112 Standards Committee. Future Committee meeting dates and locations can be found on t

28、heCommittee Page at http:/go.asme.org/A112committee.viiINTENTIONALLY LEFT BLANKviiiFRAMING-AFFIXED SUPPORTS (CARRIERS) FOROFF-THE-FLOOR PLUMBING FIXTURES1 GENERAL1.1 ScopeThis Standard covers framing-affixed supports (i.e.,carriers), with or without concealed tanks, includingcombination carriers and

29、 fittings, for off-the-floorplumbing fixtures (i.e., water closets, urinals, bidets, lava-tories, and sinks). This Standard specifies definitions,materials, general requirements, strength and deflectionrequirements, and marking requirements. It is notintended to limit the use of other materials andd

30、esigns that comply with the requirements of thisStandard.1.2 Units of MeasurementSI units are the units of record in Canada. In thisStandard,theinch/poundunitsareshowninparentheses.The values stated in each measurement system areequivalent in application; however, each system is tobe used independen

31、tly. Combining values from the twomeasurement systems can result in nonconformancewith this Standard. All references to gallons are in U.S.gallons.1.3 ReferencesThefollowingdocumentsformapartofthisStandardtotheextentspecifiedherein.Unlessotherwisespecified,thelatest edition shall apply.ASMEA112.6.1M

32、,Floor-AffixedSupportsforOff-the-FloorPlumbing Fixtures for Public UseASME A112.19.2/CSA B45.1, Ceramic plumbing fixturesASME A112.19.5/CSA B45.15, Flush valves and spuds forwater closets, urinals, and tanksASSE 1002/ASME A112.1002/CSA B125.12, Anti-siphonfill valves for water closet tanksASSE1037/A

33、SMEA112.1037/CSAB125.37,Performancerequirements for pressurized flushing devices forplumbing fixturesPublisher: The American Society ofMechanicalEngineers(ASME), Two Park Avenue, New York, NY 10016-5990(www.asme.org)CSA B45.5/IAPMO Z124, Plastic plumbing fixturesPublisher: Canadian Standards Associa

34、tion (CSA), 178Rexdale Boulevard, Toronto, Ontario M9W 1R3,Canada (www.csagroup.org)IAPMO PS 50, Flush Valves with Dual Flush Device forWater Closets or Water Closet Tank with an IntegralFlush Valves with a Dual Flush DevicePublisher: International Association of Plumbing andMechanical Officials (IA

35、PMO), 4755 East PhiladelphiaStreet, Ontario, CA 91761 (www.iapmo.org)1.4 DefinitionsA number of special terms that are specific to thecarriers covered by this Standard are defined in thissection. For additional terms pertinent to support andcarrier nomenclature, see ASME A112.6.1M.carrier: a conceal

36、ed structural bination carrier and fitting: an assembly forsupporting off-the-floor fixtures, which includes a struc-tural support, waste-fitting components, and a flushingdevice. See Figure 1.off-the-floorfixture:aplumbingfixture,locatedadjacenttoawall,whichhasnovisiblecontactwiththefloorinfrontoft

37、he wall.structuralsupport:aconcealedsupportforanoff-the-floorfixture,intendedtobeaffixedtothestructuralportionofawall.NOTE: Structural portion of a wall includes wood and steel wallframing, concrete blocks, and poured concrete.2 MATERIALS2.1 CarriersMaterials used in supports and carrierassemblies s

38、hallbe made of materials that comply with the material re-quirements specified in ASME A112.6.1M.2.2 Waste FittingsWastefittingsshallbemadeofcastiron,bronze,plastic,or other materials suitable for the intended applicationsand comply with the requirements of this Standard.3 REQUIREMENTS3.1 General3.1

39、.1 Carriers. Carriers for off-the-floor plumbingfixtures shall consist of, at a minimum, the following:(a) the (plumbing) fixture supportASME A112.6.2-20171(b) meanstoaffixthesupporttothestructuralframingwall(c) fixture bolts and hardware on which the plumbingfixtureismountedandthatconnectdirectlyto

40、thesupport(d) means to adjust the elevation of the fixture todesired height3.1.2 FootSupports.Carriers may have members (i.e.,footsupports)designedtorestonthefloorinaconcealedlocation for anchoring and supporting purposes. Whenprovided, foot supports shall be capable of extendingdownward from the ca

41、rrier to contact the floor orother framing structure to provide added support.3.2 Combination Carriers for Water Closet andUrinalsIn addition to the components of a carrier defined inpara. 3.1.1, a combination carrier (see Figure 1) forwater closets and urinals shall include the following:(a) flushi

42、ng device(b) supply piping to fixture(c) waste fitting from the fixture piping to carry thewaste from the fixture into the waste line(d) gaskets and hardware necessary to connect allcomponents (e.g., inlet and outlet pipes)3.3 Carriers for Water Closets and UrinalsWhen provided(a) flush tanks shall

43、comply with para. 4.5.2 of CSAB45.5/IAPMO Z124(b) flush valves shall comply with ASME A112.19.5/CSA B45.15 or IAPMO PS 50(c) fill valves shall comply with ASSE 1002/ASMEA112.1002/CSA B125.12(d) pressurized flushing devices shall comply withASSE 1037/ASME A112.1037/CSA B125.373.4 Waste Fittings3.4.1

44、When provided, waste fittings shall have thefollowing:(a) watertight seal at their joints(b) means of withstanding the pressure specified inpara. 4.1.23.4.2 Waste fittings for(a) water closet carriers shall be capable of passing aball with a 54 mm (2.13 in.) diameter(b) urinalcarriersshallbecapableo

45、fpassingaballwitha 23 mm (0.88 in.) diameter(c) lavatoryandbidetcarriersshallhaveanoutletwitha minimum 31.75 mm (114in.) nominal outside diameter(O.D.)Figure 1 Combination Carrier and FittingsASME A112.6.2-201723.5 Installation InstructionsManufacturers shall provide installation instructions.4 TEST

46、 REQUIREMENTS4.1 Waste Fittings4.1.1 Performance Requirements. The drainageenvelope parts of waste fittings shall show no signs ofleakage, cracking, or permanent deformation whentested in accordance with para. 4.1.2.4.1.2 TestMethod.Joints shall be made in accordancewith the manufacturers instructio

47、ns and subjected to airpressure of 35 kPa 4 kPa (5.0 psi 0.5 psi) for 1 min.4.2 Load TestSee Figure 2.4.2.1 Test Method. The carrier shall be affixed toframing members in accordance with the manufacturersinstallationinstructions,andtheplumbingfixtureshallbeassembled to the carrier. The elevation of

48、the top edge ofthe plumbing fixture at its outermost edge shall bemeasured and recorded. A load as specified in para.4.2.2 shall be applied to the center of the front edge ofthe fixture for 5 min. The load shall be applied using a76 mm (3 in.) diameter by 6 mm (0.25 in.) minimumthick, metal load-dis

49、tribution disk resting on a 13 mm(0.5 in.) thick sponge rubber or equivalent pad. Withthe load in place, the top edge elevation of the fixtureshall be measured and recorded. Ten minutes afterremoval of the load, the elevation shall be measuredand recorded again.4.2.2 Loads. Test loads shall be as follows:(a) 2225 N (500 lbf) for water closets and bidets(b) 1112 N (250 lbf) for lavatories and sinks(c) 222 N (50 lbf) for urinals4.2.3 Performance Requirements. The maximumdeflection, while the load is in place, shall not exceed6.3 mm (0.25 in.) and the residual deflecti