AIR FORCE MIL-F-38007 D-1971 FILTER ELEMENT FLUID PRESSURE MXU-233 E《MXU-233 E流体压力过滤元件》.pdf

《AIR FORCE MIL-F-38007 D-1971 FILTER ELEMENT FLUID PRESSURE MXU-233 E《MXU-233 E流体压力过滤元件》.pdf》由会员分享，可在线阅读，更多相关《AIR FORCE MIL-F-38007 D-1971 FILTER ELEMENT FLUID PRESSURE MXU-233 E《MXU-233 E流体压力过滤元件》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、- - -. , . i C .I MI-L.:F-38007D 43 7777706 0276336 W PPP-B- 566 PPP-B-576 PPP-B-58 5 PPP-B- 5 91 PPP-B-636 PPP-B-640 PPP-B - 6 7 6 PPP-T-60 MIL-F-38007D (USAF) 6 May 1971 SUPERSEDING MIL-F-38007C (USAF) 17 October 1967 MILITARY SPECIFICATION FILTER ELEMENT, FLUID, PRESSURE - lrIXU-233/E 1. SCOPE 1.

2、1 designated MXU-233/E. This specification covers one type of pressure fluid filter element, 2. APPLICABLE mmNTs 2.1 bids or request for proposal, form a part of this specification to the extent specified herein: The following documents, of the issue in effect on date of invitation for SPEC IF ICAT

3、IONS Federal Box, Folding, Paperboard Box, Wood, Cleated, Veneer, Paper Overlaid Box, Wood, Wirebound Box, Fiberboard, Wood-Cleated Box, Fiberboard Boxes, Fiberboard, Corrugated, Triple-Wall Box, Setup Tape, Pressure-Sensitive Adhesive, Waterproof, for Packaging Mil it ary ML-P- 116 MIL-G-5572 MIL-T

4、- 5 6 24 MIL-F-8901 MIL- P- 1 98 34 Preservation, Methods of Gasoline, Aviation: Turbine Fuel, Aviation, Grades JP-4 and JP-5 Filter-Separators, Aviation and Motor Fuel, Ground and Shipboard Use, Performance Requirements and Test Procedures for Plates, Identification, Metal Foil, Adhesive Backed Gra

5、des 80/87, 100/130, 115/145 FSC 4330 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- . - F- - -. 1 MIL-F-38007D 43 W 0b 0276317 T m -MTL-F-38007D (USAI?) - Military MIL-STD-100 Engineering Drawing Practices MIL-STD-105 Sampling Procedures and Tabl

6、es for Inspection by Attributes MIL-STD-129 Marking for Shipment and Storage MIL-STD-130 Identification Marking of US Military Property MIL-STD- 143 Standards and Specifications, Order of Precedence for the Selection of MIL-STD-831 Test Reports, Preparation of ._ (Copies of specifications, standards

7、, drawings, and publications required by suppliers in connection with specific procurement functions should be obtained from the procuring activity or as directed by the contracting officer) 2.2 Other publications. The following documents form a part of this specifi- cation to the extent specified h

8、erein. Unless otherwise indicated, the issue in effect on date of invitation for bids or request for proposal shall apply. American Society for Testing and Materials D 256 D 638 D 790 Standard Methods of Test for impact Resistance of Plastics and Electrical Insulating Materials Method of Test for Te

9、nsile Properties of Plastics Standard Method of Test for Flexural Properties of Plastics (Application for copies should be addressed to the American Society for Testing and Materials, 1916 Race Street, Philadelphia, Pennsylvania 19103 .) 3. REQUIREMENTS 3.1 Preproduction. This specification makes pr

10、ovisions for preproduction testing . 3.2 General specification. The requirements of MIL-F-8901 apply as require- ments of this specification with the exceptions and additions specified herein, When the two specifications conflict, this specification shall govern. 3.3 Selection of standards and speci

11、fications. Standards and specifications for necessary commodities and services not specified herein shall be selected in accordance with MIL-STD-143. 3.4 Materials 3.4.1 Metallic parts. All metallic parts of the filter element fabricated from an aluminum alloy suitable for the application. -5 2 shal

12、l be Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-. .- E - I MIL-F-38007D (USAI?) 3.4.2 Fungusproof materials. Materials that are not nutrients for fungi shall be used to the greatest extent practicable. Where materials that are nutrients for fung

13、i must be used, such materials shall be treated with a f ung ic ida1 agent. 3.4.3 Petroleum products. The materials used in the construction of the filter element shall neither affect nor be affected by petroleum products. 3.4.4 Plastic parts. If used in the construction of the filter element, molde

14、d plastic parts shall have the following physical properties: 8, Tensile strength minimum - 4,500 psi b. Flexural strength minimum - 7,500 psi c. IZOD impact minimum 1.5 pounds per inch of notch. 3.5 Design and construction. The filter element shall be so designed and constructed that no parts will

15、work loose in service. It shall be built to withstand the stresses, jars, vibrations, and other conditions incident to shipping, storage, installation, and flight line service. 3.5.1 Functional design. The filter element shall be designed for instal- lation in the Warner-Lewis Division of Pram Corpo

16、ration filter-separators specified in 6.1.1, The filter element shall be as shown on figure 1. 3.5.1.1 Compatible fuels. The filter element shall be so designed that it can be used with fuels conforming to MIL-G-5572 and MIL-T-5624. 3.5.1.2 Gasket. A gasket shall be furnished with each filter elemen

17、t. The gasket shall have an inside diameter of 2-1/4 inches, an outside diameter of 3-1/2 inches, and shall be 1/8 inch thick. The material for the gasket shall be Buna N or other materiai compatible with turbine fuels conforming to MIL-T-5624. 3.6 Performance. When 10 elements are installed in a Wa

18、rner-Lewis Division of Pram Corporation model FCS 105 filter-separator, the elements shall be capable of meeting the performance requirements of MIL-F-8901 at a flow rate of 100 gpm, except the maximum water removal capability shall be 5 percent by volume. 3.7 Part numbering of interchangeable parts

19、. All parts having the same manu- facturers part number shall be functionally and dimensionally interchangeable. The item identification and part number requirements of MIL-STD-100 shall govern the manufacturers part numbers and changes thereto. 3 Provided by IHSNot for ResaleNo reproduction or netw

20、orking permitted without license from IHS-,-,-. - 4 v) w I o 1-110 iu U Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-1- . 3 MIL-F - 3 8 O0 7 D (US AF) 3.8 Idcnti icatjon of product. The following in forination slinll be iiiarkrl on each filter ele

21、ment in accordance with MIL-STD-130. If the itcni is iriarkcd on any sealing urface, the markings shall not affect the sealing of the element. Manufacturers part No. Manufacturers name or trademark Date of manufacture . 3.8.1 Manufacturers part number. The manufacturers part number and drawing numbe

22、r shall be the same. 3.8.2 Nameplate. A nameplate conforming to type I of MIL-P-19834 shall be supplied one per each 10 elements shipped. Attaching instructions shall be affixed to each nameplate. The nameplate shall conform to figure 2. 3.9 Workmanship. The filter element, includfng all parts, shal

23、l be constructed and finished in a thoroughly workmanlike manner. Particular attention shall be given to neatness and thoroughness of marking of parts and assemblies and free- dom of parts from burrs and sharp edges. 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection. Unless otherwise

24、 specified in the con- tract or purchase order, the supplier is responsible for the performance of all inspection requirements as specified herein. Except as otherwise speci- fied in the contract or order, the supplier may use his own or any other facilities suitable for the performance of the inspe

25、ction requirements specified herein, unless disapproved by the Government. The Government reserves the right to perform any of the inspections set forth in the specification where such inspections are deemed necessary to assure supplies and services conform to prescribed requirements. 4.1.1 Inspecti

26、on and testing. The inspection and testing of the filter element shall be conducted in a full-scale filter-separator unit in accordance with MIL-F-8 901 and as spec if ied herein. 4.2 Test condition. During all applicable full-scale testing, 10 filter . elements shall be mounted in a Warner-Lewis Di

27、vision of Fram Corporation model FCS 105 ilter-separator. 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-flL-F-3OO7D LI3 W 9999906 0276323 I W I- l FILTER - SEPARATOR ELEM EN T DATA ,=ELEMENTS FIRST STAGE: PART NRt FSN 0.0. 3s INCHES LENGTH I0 INC

28、HES CONTRACT NR+ MANUFACTURER + :,ELEMENT CHANGE CRITERIA; SpoOpOO GAL 600 GPM UNIT 2,500,000GAL WGPMUNI 1,700,000GAL 200 GPM UNIT 800,000 GAL 100 GPM UNIT EVERY 2 YEARS-20 PSI DIFF PRESS. I WHICHEVER OCCURS FIRST Y DATE ELEMENTS INSTALLEDO METER TOTALIZER READINGO +APPLCABLE INFORMATION TO BE PROVI

29、DED BY CONTRACTOR OPROVIDE APPLICABLE SURFACE l ALLOW DATA TO BE MARKED IN BY GOVERNMENT PERSONNEL NOT ES: 1. ALL LETTERING SHALL BE 3132- INCH HIGH, UNLESS , OTHERWISE NOTED 2,BACKGROUND SHALL BE BLUE 3. DIMENSIONS IN INCHES, TOLERANCE ? #2 FIGURE 2. Nameplate 6 39 5 1 f 3 iL 0 Provided by IHSNot f

30、or ResaleNo reproduction or networking permitted without license from IHS-,-,-4.3 Preproduction testing (see 6.2) 4.3.1 Test samples. Unless otherwise specidied (see 6.2), the preproduction test samples shall consist of 51 elements representative of a production lot (see 6.3,l). The samples shall be

31、 identified-with the manufacturers part number and such other inforhation as required by the procuring activity. Samples shall be prepared as follows: 4.3.1.1 be accompanied by the following data: Data to accompany test samples, The preproduction test samples shall a. install and operate the equipme

32、nt Brief operating and installation data to enable test personnel to correctly b. Engineering data in the form of assembly drawings (two sets). 4.3.1.2 at a site other than the laboratory of the procuring activity, the following Test sample and data for procuring activity, When tests are conducted s

33、hall be furnished that activity: a. Three copies of a test report in accordance with MIL-STD-831. In addition to results, the report shall contain complete records of the tests, including data sheets, performance curves, chronological test records, photographs, sample calculations,test procedures, a

34、nd a description of the test apparatus. b. the preproduction tests A sample element removed from the filter-separator which was subjected to C. Color photograph of the sample element d. A new filter element. 4.3.2 Preproduction tests. The preproduction tests shall consist of the applicable tests spe

35、cified in MIL-F-8901, except as follows: a. Water removal tests at 10 percent during the third hour are not required b. and single-pass tests shall be performed at 20 gpm During the inhibited fuel test, two elements shall be mounted in parallel c. 100 gpm During the full-scale tests, the fuel flow r

36、ate of capacity shall be 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-38007D (USAI?) d. Sections of the plastic mater-ia1 if used in the construction of the. element or specially prepared test specimens shall be testcd as fol.lows to vezfy

37、 plastic material compliance. The resultant test data shall bc iiicluded in the test report, (1) Tensile strength - ASTM D638, type I (2) Flexural strength - ASTM D790 (3) IZOD impact strength (notched) - ASTM D256, method A e. assembled and inspected to determine the condition of the filter element

38、s. Defects in the elements such as swelling, damaged elements, and damaged gaskets shall be noted. Excessive swelling of or damage to the elements or other parts shall be cause for rejection. Upon completion of the life test, the filter-separator shall be dis- 4.4 Acceptance tests. The acceptance te

39、sts shall consist of the following: a. individual tests See 4.4.1 Sampling plan and test . See 4.4.2. b; 4.4.1 Individual tests. examination of product paragraph of MIL-F-8901, and to determine if it conforms to the filter elements design configuration used during preproduction testing. Each element

40、 shall be examined as required by the 4.4.2 Sampling plan and test. selected at random from each lot in accordance with MIL-STD-105 and subjected to the f ilter/coalescer element tests specified in MIL-F-8901. An AQL of 1.5 percent, inspection level I, shall be established. This test shall be consid

41、ered destructive. Samples of the filter elements shall be 4.5 Inspection of preparation for delivery. Preservation, packaging, packing, and marking shall be inspected to determine conformance to the requirements of section 5 herein. 5. PREPARATION FOR DELIVERY 5.1 Packaging (see 6.2) 5.1.1 Level A.

42、One filter element shall be packaged in accordance with method III of MIL-P-116 in a container conforming to PPP-B-566, PPP-B-676, or PPP-B-636. 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-F-38007D (USAE) 5.1.1.1 Nameplate. Each nameplate s

43、hall be packaged in accordance with method III Of MIL-P-116. 5.1.1.2 Intermediate packaging. Ten unit-packaged fiiter elements and one packaged nameplate shall be intermediate packaged in a container conforming to PPP-B-636. 5.1.2 Level C. Preservation and packaging shall be the minimum necessary to

44、 afford protection against corrosion, deterioration, and physical damage during shipment from the supply source to the first receiving activity. 5.2 Packing (see 6.21 5.2.1 Level A. Filter elements shall be packed in overseas-type containers conforming to PFP-B-576, PPP-B-585, PPP-B-591, PPP-B-636,

45、or PPP-B-640. Cori- tainers shall be of minimum weight and cube, uniform size and shape, and shall contain like quantities, when practical. Closure of the containers shall be in accordance with the applicable specification and appendix thereto. Con- tainers in accordance with PPP-B-636 shall be seal

46、ed at all joints and seams with tape conforming to PPP-T-60, 5.2.2 Level B. The filter element shall be packed as specified in 5.2.1, except Containers shall be of the domestic type and closure shall be in accor- dance with the requirements for domestic containers. 5.2.3 Level C. Packages which requ

47、ire overpacking for acceptance by the carrier shall be packed in shipping containers in a manner that will insure safe delivery at the lowest transportation and packing charges. Containers shall meet Consolidated Freight rules and regulations or other rules and regulations applicable to the mode of

48、transportation. 5.3 Shipment marking. In addition to any special marking required by the contract or order (see 6.2) all shipping containers shall be marked in accordance with MIL-STD-129. The nomenclature shall be as follows: FILTER ELEMENT, FLUID, PRESSURE MXU-233/Ee 6. NOTES 6.1 Intended use. The

49、 MXU-233/E filter element is intended for use as a replacement item in ground aviation liquid fuel filtering and servicing systems. This filter element is intended to replace the Warner-Lewis Division of Fram Corporation part No. CC-18 elements. 9 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-6.1.1 Quantity of elements