IEEE C37 40-2003 en Service Conditions and Definitions for High-Voltage Fuses Distribution Enclosed Single-Pole Air Switches Fuse Disconnecting Switches and Acc.pdf

《IEEE C37 40-2003 en Service Conditions and Definitions for High-Voltage Fuses Distribution Enclosed Single-Pole Air Switches Fuse Disconnecting Switches and Acc.pdf》由会员分享，可在线阅读，更多相关《IEEE C37 40-2003 en Service Conditions and Definitions for High-Voltage Fuses Distribution Enclosed Single-Pole Air Switches Fuse Disconnecting Switches and Acc.pdf（41页珍藏版）》请在麦多课文档分享上搜索。

1、IEEE Std C37.40-2003(Revision of IEEE Std C37.40-1993)IEEE StandardsC37.40TMIEEE Standard Service Conditionsand Definitions for High-VoltageFuses, Distribution Enclosed Single-Pole Air Switches, FuseDisconnecting Switches, andAccessoriesPublished by The Institute of Electrical and Electronics Engine

2、ers, Inc.3 Park Avenue, New York, NY 10016-5997, USA25 February 2004IEEE Power Engineering SocietySponsored by theSwitchgear CommitteeIEEE StandardsPrint: SH95182PDF: SS95182Authorized licensed use limited to: IEEE Standards Staff. Downloaded on March 23, 2009 at 15:42 from IEEE Xplore. Restrictions

3、 apply.Recognized as anAmerican National Standard (ANSI)The Institute of Electrical and Electronics Engineers, Inc.3 Park Avenue, New York, NY 10016-5997, USACopyright 2004 by the Institute of Electrical and Electronics Engineers, Inc.All rights reserved. Published 27 February 2004. Printed in the U

4、nited States of America.IEEE is a registered trademark in the U.S. Patent distribution current-limiting fuses; distribution enclosed single-pole air switches; power fuses,including current-limiting types; outdoor and indoor fuse disconnecting switches; fuse supports,mountings, switch sticks, and lin

5、ks, all of the type used exclusively with the above; and removableswitch blades for certain products among the above.Keywords: distribution enclosed single-pole air switch, fuse accessories, fuse disconnectingswitch, high-voltage fuseIEEE Standards documents are developed within the IEEE Societies a

6、nd the Standards Coordinating Committees of theIEEE Standards Association (IEEE-SA) Standards Board. The IEEE develops its standards through a consensus develop-ment process, approved by the American National Standards Institute, which brings together volunteers representing variedviewpoints and int

7、erests to achieve the final product. Volunteers are not necessarily members of the Institute and serve with-out compensation. While the IEEE administers the process and establishes rules to promote fairness in the consensus devel-opment process, the IEEE does not independently evaluate, test, or ver

8、ify the accuracy of any of the information containedin its standards.Use of an IEEE Standard is wholly voluntary. The IEEE disclaims liability for any personal injury, property or other dam-age, of any nature whatsoever, whether special, indirect, consequential, or compensatory, directly or indirect

9、ly resultingfrom the publication, use of, or reliance upon this, or any other IEEE Standard document.The IEEE does not warrant or represent the accuracy or content of the material contained herein, and expressly disclaimsany express or implied warranty, including any implied warranty of merchantabil

10、ity or fitness for a specific purpose, or thatthe use of the material contained herein is free from patent infringement. IEEE Standards documents are supplied “AS IS.”The existence of an IEEE Standard does not imply that there are no other ways to produce, test, measure, purchase, market,or provide

11、other goods and services related to the scope of the IEEE Standard. Furthermore, the viewpoint expressed at thetime a standard is approved and issued is subject to change brought about through developments in the state of the art andcomments received from users of the standard. Every IEEE Standard i

12、s subjected to review at least every five years for revi-sion or reaffirmation. When a document is more than five years old and has not been reaffirmed, it is reasonable to concludethat its contents, although still of some value, do not wholly reflect the present state of the art. Users are cautione

13、d to checkto determine that they have the latest edition of any IEEE Standard.In publishing and making this document available, the IEEE is not suggesting or rendering professional or other servicesfor, or on behalf of, any person or entity. Nor is the IEEE undertaking to perform any duty owed by an

14、y other person orentity to another. Any person utilizing this, and any other IEEE Standards document, should rely upon the advice of a com-petent professional in determining the exercise of reasonable care in any given circumstances.Interpretations: Occasionally questions may arise regarding the mea

15、ning of portions of standards as they relate to specificapplications. When the need for interpretations is brought to the attention of IEEE, the Institute will initiate action to prepareappropriate responses. Since IEEE Standards represent a consensus of concerned interests, it is important to ensur

16、e that anyinterpretation has also received the concurrence of a balance of interests. For this reason, IEEE and the members of its soci-eties and Standards Coordinating Committees are not able to provide an instant response to interpretation requests except inthose cases where the matter has previou

17、sly received formal consideration. At lectures, symposia, seminars, or educationalcourses, an individual presenting information on IEEE standards shall make it clear that his or her views should be consideredthe personal views of that individual rather than the formal position, explanation, or inter

18、pretation of the IEEE. Current in-terpretations can be accessed at the following URL: http:/standards.ieee.org/reading/ieee/interp/index.html.Errata, if any, for this and all other standards can be accessed at the following URL: http:/standards.ieee.org/reading/ieee/updates/errata/index.html. Users

19、are encouraged to check this URL for errata periodically.Comments for revision of IEEE Standards are welcome from any interested party, regardless of membership affiliation withIEEE. Suggestions for changes in documents should be in the form of a proposed change of text, together with appropriatesup

20、porting comments. Comments on standards and requests for interpretations should be addressed to:Secretary, IEEE-SA Standards Board445 Hoes LaneP.O. Box 1331Piscataway, NJ 08855-1331USAAuthorization to photocopy portions of any individual standard for internal or personal use is granted by the Instit

21、ute ofElectrical and Electronics Engineers, Inc., provided that the appropriate fee is paid to Copyright Clearance Center. Toarrange for payment of licensing fee, please contact Copyright Clearance Center, Customer Service, 222 Rosewood Drive,Danvers, MA 01923 USA; +1 978 750 8400. Permission to pho

22、tocopy portions of any individual standard for educationalclassroom use can also be obtained through the Copyright Clearance Center.NOTEAttention is called to the possibility that implementation of this standard may require use of subjectmatter covered by patent rights. By publication of this standa

23、rd, no position is taken with respect to the exist-ence or validity of any patent rights in connection therewith. The IEEE shall not be responsible for identifyingpatents for which a license may be required by an IEEE standard or for conducting inquiries into the legal valid-ity or scope of those pa

24、tents that are brought to its attention.Authorized licensed use limited to: IEEE Standards Staff. Downloaded on March 23, 2009 at 15:42 from IEEE Xplore. Restrictions apply.Copyright 2004 IEEE. All rights reserved. iiiIntroduction(This introduction is not part of IEEE Std C37.40-2003, IEEE Standard

25、Service Conditions and Definitions for High-Voltage Fuses, Distribution Enclosed Single-Pole Air Switches, Fuse Disconnecting Switches, and Accessories.)This standard is a revision of IEEE Std C37.40-1993, to bring it up-to-date and in-line with present dayrequirements for high-voltage fuses and swi

26、tches. Supplement IEEE Std C37.40B-1996 has been incorpo-rated. Temperature rise requirements presently used in IEC fuse standards have been adopted, while altitudecorrection factors have been removed from the standard, due to the current controversy surrounding theiruse. Historically used altitude

27、correction factors, together with proposals from the IEEE Switchgear Com-mittee Common Clauses Working Group, have been put in informative Annex A and informative Annex B. This standard was prepared by the Revision of Fuse Standards Working Group of the IEEE Subcommitteeon High-Voltage Fuses. Liaiso

28、n was maintained with the National Electrical Manufacturers Association(NEMA) and the International Electrotechnical Commission (IEC) during the development of the revisionsin order to incorporate the latest activities at the time of publication. It is one of a series of complementarystandards cover

29、ing various types of high-voltage fuses and switches, arranged so that certain standards applyto all devices while other standards provide additional specifications for a particular device. For any device,IEEE Std C37.40-2003, IEEE Std C37.41-2000, plus the additional standard covering that device,

30、consti-tute a complete standard for the device. In addition, IEEE Std C37.48-1997 is an application, operation,and maintenance guide for all the devices, and IEEE Std. C37.48.1-2002 is an operation, classification,application, and coordination guide for current-limiting fuses.The following standards

31、 make up this series: ANSI C37.42-1996, American National Standard Specification for High Voltage Expulsion TypeDistribution Class Fuses, Cutouts, Fuse Disconnecting Switches, and Fuse Links.ANSI C37.45-1981 (Reaff 1992), American National Standard Specifications for Distribution EnclosedSingle-Pole

32、 Air Switches.ANSI C37.46-2000, American National Standard for High Voltage Expulsion and Current-Limiting TypePower Class Fuses and Fuse Disconnecting Switches.ANSI C37.47-2000, American National Standard for High-Voltage Current-Limiting Type DistributionClass Fuses and Fuse Disconnecting Switches

33、. IEEE Std C37.40-2003, IEEE Standard Service Conditions and Definitions for High-Voltage Fuses,Distribution Enclosed Single-Pole Air Switches, Fuse Disconnecting Switches, and Accessories.IEEE Std C37.41-2000, IEEE Standard Design Tests for High-Voltage Fuses, Distribution Enclosed Single-Pole Air

34、Switches, Fuse Disconnecting Switches, and Accessories. IEEE Std C37.48-1997, IEEE Guide for Application, Operation, and Maintenance of High-Voltage Fuses,Distribution Enclosed Single-Pole Air Switches, Fuse Disconnecting Switches, and Accessories.IEEE Std C37.48.1-2002, IEEE Guide for the Operation

35、, Classification, Application, and Coordination ofCurrent-Limiting Fuses with Rated Voltages 138 kV.Authorized licensed use limited to: IEEE Standards Staff. Downloaded on March 23, 2009 at 15:42 from IEEE Xplore. Restrictions apply.iv Copyright 2004 IEEE. All rights reserved.ParticipantsAt the time

36、 this standard was completed, the Revision of Fuse Standards Working Group had the followingmembership:John G. Leach, ChairGlenn R. Borchardt, SecretaryThe High-Voltage Fuses Subcommittee that authorized the formation of the balloting group had the follow-ing membership:Tim E. Royster, ChairJohn G.

37、Leach, SecretaryThe following members of the balloting committee voted on this standard. Balloters may have voted forapproval, disapproval, or abstention. John G. Angelis Richard H. Arndt L. Ronald Beard Terrance A. Bellei Fredrick J. BrownH. Edward FoelkerStephen P. Hassler James R. Marek Frank J.

38、Muench R. Neville ParryRadhakrishna Ranjan Philip Rosen Tim E. Royster John S. Schaffer E. William Schmunk Mark W. Stavnes Frank M. StepniakJohn G. St. Clair E. M. “Al” WorlandMaria ZandonellaJanusz ZawadzkiJohn G. Angelis Richard H. Arndt L. Ronald Beard Terrance A. Bellei Glenn R. Borchardt Fredri

39、ck J. BrownRaymond L. CapraH. Edward FoelkerStephen P. Hassler James R. Marek Frank J. Muench R. Neville ParryHerbert M. PflanzRadhakrishna Ranjan John S. Schaffer E. William Schmunk Mark W. Stavnes Frank M. StepniakJohn G. St. Clair John G. WoodMaria ZandonellaJanusz ZawadzkiRoy AlexanderStan J. Ar

40、notW. J. (Bill) BergmanStan BillingsThomas BlairGlenn R. BorchardtTed BurseE. R. ByronRaymond L. CapraTommy CooperRonald DaubertAlexander DixonRandall DotsonDenis DufournetAmir El-SheikhGary EngmannMarcel FortinMietek GlinkowskiRandall GrovesErik GuillotEdward Horgan, Jr.Bill HurstDavid JacksonRicha

41、rd JacksonDavid KrauseJohn LeachJason LinR. W. LongGregory LuriWilliam MajeskiNigel McQuinGary MichelAlec MonroeGeorges MontilletPeter MorganFrank MuenchT. W. OlsenR. Neville ParryEdward PetersAnthony PicagliRadhakrishna RanjanTimothy RoysterJames RuggieriJohn S. SchafferE. William SchmunkFrank M. S

42、tepniakAlan StormsStanton TelanderJoseph TumidajskiCharles WagnerJames WilsonJohn G. WoodElbert WorlandJanusz ZawadzkiDonald W. ZipseAuthorized licensed use limited to: IEEE Standards Staff. Downloaded on March 23, 2009 at 15:42 from IEEE Xplore. Restrictions apply.Copyright 2004 IEEE. All rights re

43、served. vWhen the IEEE-SA Standards Board approved this standard on 11 September 2003, it had the followingmembership:Don Wright, ChairHoward M. Frazier, Vice ChairJudith Gorman, Secretary*Member EmeritusAlso included are the following nonvoting IEEE-SA Standards Board liaisons:Alan Cookson, NIST Re

44、presentativeSatish K. Aggarwal, NRC RepresentativeNoelle D. HumenickIEEE Standards Project EditorH. Stephen BergerJoseph A. BruderBob DavisRichard DeBlasioJulian Forster*Toshio FukudaArnold M. GreenspanRaymond HapemanDonald N. HeirmanLaura HitchcockRichard H. HulettAnant Kumar JainLowell G. JohnsonJ

45、oseph L. Koepfinger*Tom McGeanSteve M. MillsDaleep C. MohlaWilliam J. MoylanPaul NikolichGary S. RobinsonMalcolm V. ThadenGeoffrey O. ThompsonDoug ToppingHoward L. WolfmanAuthorized licensed use limited to: IEEE Standards Staff. Downloaded on March 23, 2009 at 15:42 from IEEE Xplore. Restrictions ap

46、ply.vi Copyright 2004 IEEE. All rights reserved.Contents1. Overview 11.1 Scope 11.2 Background 22. References and related standards. 23. Service conditions 33.1 Usual service conditions 33.2 Other service conditions 33.3 Correction of altitudes in excess of 1000 m 44. Definitions . 44.1 General defi

47、nitions. 44.2 Ratings . 224.3 Tests. 26Annex A (informative) Altitude correction factors (historical). 28Annex B (informative) Altitude correction factors (from proposed common specifications standard) 29Annex C (informative) Bibliography. 33Authorized licensed use limited to: IEEE Standards Staff.

48、Downloaded on March 23, 2009 at 15:42 from IEEE Xplore. Restrictions apply.Copyright 2004 IEEE. All rights reserved. 1IEEE Standard Service Conditions and Definitions for High-Voltage Fuses, Distribution Enclosed Single-Pole Air Switches, Fuse Disconnecting Switches, and Accessories1. Overview1.1 Sc

49、opeThis standard applies to high-voltage (above 1000 V) fuses and equipment. This includes distribution classand power class fuses, distribution class enclosed single-pole air switches, distribution class and power classfuse disconnecting switches, and associated accessories that are intended for use on ac distribution systems.This standard applies to the following specific types of equipment:a) Distribution class and power class expulsion type fusesb) Distribution class and power class current-limiting fusesc) Distribution class and power class fuse disconnecting switches