IEEE 1515-2000 en Recommended Practice for Electronic Power Subsystems Parameter Definitions Test Conditions and Test Methods《电子大功率子系统的推荐规程 参数定义、试验条件和方法》.pdf

《IEEE 1515-2000 en Recommended Practice for Electronic Power Subsystems Parameter Definitions Test Conditions and Test Methods《电子大功率子系统的推荐规程 参数定义、试验条件和方法》.pdf》由会员分享，可在线阅读，更多相关《IEEE 1515-2000 en Recommended Practice for Electronic Power Subsystems Parameter Definitions Test Conditions and Test Methods《电子大功率子系统的推荐规程 参数定义、试验条件和方法》.pdf（83页珍藏版）》请在麦多课文档分享上搜索。

1、The Institute of Electrical and Electronics Engineers, Inc.3 Park Avenue, New York, NY 10016-5997, USACopyright 2000 by the Institute of Electrical and Electronics Engineers, Inc.All rights reserved. Published 15 September 2000. Printed in the United States of America.Print: ISBN 0-7381-2488-5 SH948

2、53PDF: ISBN 0-7381-2489-3 SS94853No part of this publication may be reproduced in any form, in an electronic retrieval system or otherwise, without the prior written permission of the publisher.IEEE Std 1515-2000(R2008)IEEE Recommended Practice for Electronic Power Subsystems: Parameter Definitions,

3、 Test Conditions, and Test MethodsSponsorStandards Committeeof theIEEE Power Electronics SocietyReaffirmed 10 December 2008Approved 30 March 2000IEEE-SA Standards BoardReaffirmed 14 May 2009Approved 30 March 2000American National Standards InstituteAbstract: This recommended practice defines many co

4、mmon parameters for ac-dc and dc-dc elec-tronic power distribution components and subsystems. This enables electronic system engineers,manufacturers, and researchers to speak with a common language and hence facilitates effectiveand efficient communications. Furthermore, implementation of a common s

5、pecification languagewill allow the power electronics industry as well as the user communities, including government sys-tem developers, to acquire cost- and time-effective electronic power subsystems with significantlyenhanced interchangeability.Keywords: electronic power distribution, power subsys

6、tem, power supply, specification, specifica-tion languageAuthorized licensed use limited to: IHS Stephanie Dejesus. Downloaded on August 27, 2009 at 09:16 from IEEE Xplore. Restrictions apply. IEEE Standardsdocuments are developed within the IEEE Societies and the Standards Coordinating Com-mittees

7、of the IEEE Standards Association (IEEE-SA) Standards Board. Members of the committees servevoluntarily and without compensation. They are not necessarily members of the Institute. The standardsdeveloped within IEEE represent a consensus of the broad expertise on the subject within the Institute asw

8、ell as those activities outside of IEEE that have expressed an interest in participating in the development ofthe standard.Use of an IEEE Standard is wholly voluntary. The existence of an IEEE Standard does not imply that thereare no other ways to produce, test, measure, purchase, market, or provide

9、 other goods and services related tothe scope of the IEEE Standard. Furthermore, the viewpoint expressed at the time a standard is approved andissued is subject to change brought about through developments in the state of the art and commentsreceived from users of the standard. Every IEEE Standard i

10、s subjected to review at least every ve years forrevision or reafrmation. When a document is more than ve years old and has not been reafrmed, it is rea-sonable to conclude that its contents, although still of some value, do not wholly reect the present state ofthe art. Users are cautioned to check

11、to determine that they have the latest edition of any IEEE Standard.Comments for revision of IEEE Standards are welcome from any interested party, regardless of membershipafliation with IEEE. Suggestions for changes in documents should be in the form of a proposed change oftext, together with approp

12、riate supporting comments.Interpretations: Occasionally questions may arise regarding the meaning of portions of standards as theyrelate to specic applications. When the need for interpretations is brought to the attention of IEEE, theInstitute will initiate action to prepare appropriate responses.

13、Since IEEE Standards represent a consensus ofall concerned interests, it is important to ensure that any interpretation has also received the concurrence of abalance of interests. For this reason, IEEE and the members of its societies and Standards CoordinatingCommittees are not able to provide an i

14、nstant response to interpretation requests except in those cases wherethe matter has previously received formal consideration. Comments on standards and requests for interpretations should be addressed to:Secretary, IEEE-SA Standards Board445 Hoes LaneP.O. Box 1331Piscataway, NJ 08855-1331USAIEEE is

15、 the sole entity that may authorize the use of certication marks, trademarks, or other designations toindicate compliance with the materials set forth herein.Authorization to photocopy portions of any individual standard for internal or personal use is granted by theInstitute of Electrical and Elect

16、ronics Engineers, Inc., provided that the appropriate fee is paid to CopyrightClearance Center. To arrange for payment of licensing fee, please contact Copyright Clearance Center, Cus-tomer Service, 222 Rosewood Drive, Danvers, MA 01923 USA; (978) 750-8400. Permission to photocopyportions of any ind

17、ividual standard for educational classroom use can also be obtained through the Copy-right Clearance Center.Note: Attention is called to the possibility that implementation of this standard mayrequire use of subject matter covered by patent rights. By publication of this standard,no position is take

18、n with respect to the existence or validity of any patent rights inconnection therewith. The IEEE shall not be responsible for identifying patents forwhich a license may be required by an IEEE standard or for conducting inquiries intothe legal validity or scope of those patents that are brought to i

19、ts attention.Authorized licensed use limited to: IHS Stephanie Dejesus. Downloaded on August 27, 2009 at 09:16 from IEEE Xplore. Restrictions apply. Copyright 2000 IEEE. All rights reserved.iiiIntroduction(This introduction is not part of IEEE Std 1515-2000, IEEE Recommended Practice for Electronic

20、Power Subsystems:Parameter Denitions, Test Conditions, and Test Methods.)Electronic power subsystems are integral parts of any electronic system. They perform the tasks of powerprocessing, management, and distribution. Clear denition and precise understanding of the terms (or termi-nology) used in a

21、 specication are crucial to successful and cost-effective development programs.This recommended practice attempts to dene a parameter specication language for common parametersused to describe ac-dc and dc-dc electronic power distribution components and subsystems. This parameterspecication language

22、 consists of test parameter denitions, test methods, and test conditions.In the past two decades, the power electronics industry has experienced tremendous success and growth. Forinstance, switched-mode power supplies now occupy 95% of the market (compared to only 12% in the1970s) and switched-mode

23、motor devices are replacing traditional motor drives in virtually all applications.As with many other maturing technologies, unprecedented growth creates a problem that hinders furthersuccess and growth. That problem is the lack of a common parameter specication language.Lack of a common parameter s

24、pecication language creates confusion among industry manufacturers andsystems developers. Different manufacturers and subsystem developers use similar terms to indicate differ-ent performance. This confusion not only hinders effective communication and the interchangeability amongproducts, but also

25、increases the cost and time for both development and procurement. This is particularlytrue for high-end customer designs, such as those intended for military and aerospace applications. A common specication language will allow the power electronics industry and the government systemdevelopers to acq

26、uire cost- and time-effective electronic power subsystems with signicantly enhancedinterchangeability. This recommended practice was written with test methods that include test equipmentcharacteristics rather than a requirement for specic test equipment. Implementation of this recommendedpractice wi

27、ll allow the subsystem designer to make performance comparisons among the contending elec-tronic power distribution subsystem components that have been specied to the same criteria. Products willhave been consistently specied and performance tested; thereby, minimizing buyer condence testing. The ev

28、aluation of competing products from different manufacturers for intra-operability will be a less expen-sive effort. The component developer who adheres to this recommended practice will ensure that customerscan unambiguously understand their product specications, increasing customer condence and sat

29、isfaction.This recommended practice collects, in a single document, most of the parameters used in specifying apower electronic product. As such, it will be useful both for systems engineers (who specify requirementsfor products) and for designers (who qualify their products to the specications). Th

30、is will also be useful forengineers and graduate students who are entering the eld of power electronics, since many of the parame-ters are seldom discussed fully in university courses or in professional educational seminars.Authorized licensed use limited to: IHS Stephanie Dejesus. Downloaded on Aug

31、ust 27, 2009 at 09:16 from IEEE Xplore. Restrictions apply. ivCopyright 2000 IEEE. All rights reserved.ParticipantsThe preparation of this recommended practice was accomplished by the IEEE Working Group on ElectronicPower Specication (P1515). At the time of its completion, the Working Group consiste

32、d of the followingmembers:F. Dong Tan,ChairCarlos Gonzalez,SecretaryThe following members of the balloting committee voted on this standard:When the IEEE-SA Standards Board approved this standard on 30 March 2000, it had the followingmembership:Donald N. Heirman,ChairJames T. Carlo,Vice ChairJudith

33、Gorman,Secretary*Member EmeritusAlso included is the following nonvoting IEEE-SA Standards Board liaison:Alan Cookson, NIST RepresentativeDonald R. Volzka, TAB RepresentativeCatherine BergerIEEE Standards Project EditorTom AlbrightJeff BledsoeDave CooperCraig ElderRobert GlenwoodTed HoffmannGeorge K

34、aelinBarbara KennyHarry LamberthYan-Fei LiuGlen LoganEd MabeIshaque S. MehdiSergio Navarro Ernie Parker Mario RinaldiHarry Sagara Marvin Soraya John Traver Greg WilterdinkArt BrockschmidtCharles Clark, Jr.Steve FreelandDouglas C. HopkinsJerry HudginsJeffrey HwangGeorge KaelinArthur KelleyPhilip Krei

35、nJih-Sheng LaiHarry LamberthAnthony F. LavianoHenry T. LeeYan-Fei LiuChuck MullettBalarama V. MurtyDaniel SableJian SunF. Dong TanJavier UcedaJim WalkerRobert WhiteSatish K. AggarwalMark D. BowmanGary R. EngmannHarold E. EpsteinH. Landis FloydJay Forster*Howard M. FrazierRuben D. GarzonJames H. Gurn

36、eyRichard J. HollemanLowell G. JohnsonRobert J. KennellyJoseph L. Koepnger*Peter H. LipsL. Bruce McClungDaleep C. MohlaJames W. MooreRobert F. MunznerRonald C. PetersenGerald H. PetersonJohn B. PoseyGary S. RobinsonAkio TojoDonald W. ZipseAuthorized licensed use limited to: IHS Stephanie Dejesus. Do

37、wnloaded on August 27, 2009 at 09:16 from IEEE Xplore. Restrictions apply. Copyright 2000 IEEE. All rights reserved.vContents1. Overview11.1 Scope11.2 Purpose.11.3 Organization of the recommended practice.22. References23. Definitions of terms and acronyms34. Electrical performance parameters94.1 DC

38、 voltage.94.2 AC voltage.94.3 Efficiency.134.4 Regulation154.5 Ripple and spikes.244.6 Transients.284.7 Impedance304.8 On/Off control324.9 Isolation and grounding.354.10 Distortion.364.11 Conducted emissions.404.12 Susceptibility434.13Use of multiple power supplies in a system.504.14 Adjustments and

39、 control524.15 Fault protection545. Reliability, maintainability, environmental, and mechanical parameters605.1 Reliability.605.2 Maintainability.615.3 Environments.625.4 Mechanical.67Annex A (informative) Bibliography70Annex B (informative) General test practices.71Authorized licensed use limited t

40、o: IHS Stephanie Dejesus. Downloaded on August 27, 2009 at 09:16 from IEEE Xplore. Restrictions apply. Authorized licensed use limited to: IHS Stephanie Dejesus. Downloaded on August 27, 2009 at 09:16 from IEEE Xplore. Restrictions apply. Copyright 2000 IEEE. All rights reserved.1IEEE Recommended Pr

41、actice for Electronic Power Subsystems: Parameter Denitions, Test Conditions, and Test Methods1. Overview1.1 Scope This recommended practice is written to provide a standard specication language for common parametersused to characterize the performance of electronic power distribution subsystem elem

42、ents. Specically, theseare parameters relating to the integration of power supplies into electronic power distribution subsystems.The specication language consists of parameter denitions, test methods, and test conditions for the param-eters. The specication language is meant to be used by both elec

43、tronic power subsystem developers anddesigners and component manufacturers to insure unambiguous communication. The specication language is intended to be applied to ac-dc and dc-dc electronic power distribution sub-systems. The range of power subsystems includes single-phase and three-phase systems

44、, with power levelsfrom a fraction of a watt to 20 kW. The voltage range is from a few volts to 600 V, at a frequency or frequen-cies of dc 1 kHz. However, this recommended practice can be used outside the range.1.2 PurposeThe purpose of this recommended practice is to standardize a specication lang

45、uage, not to specify orenforce “a standard specication.” A specication written in compliance with this language will ensure easyand precise understanding between manufacturers and users without, in any way, limiting manufacturersability to present features that are special to their products. Efforts

46、 have been made to include as many common parameters as possible, but this recommended practiceis by no means meant to be all-inclusive.Authorized licensed use limited to: IHS Stephanie Dejesus. Downloaded on August 27, 2009 at 09:16 from IEEE Xplore. Restrictions apply. IEEEStd 1515-2000 IEEE RECOM

47、MENDED PRACTICE FOR ELECTRONIC POWER SUBSYSTEMS:2Copyright 2000 IEEE. All rights reserved.1.3 Organization of the recommended practiceThis recommended practice is organized into ve clauses and two annexes. Clause 1 is an overview of thescope, purpose, and organization of the document. Clause 2 lists

48、 all the references that should be consultedwhen using this recommended practice. Clause 3 identies the terms and acronyms that are used throughoutthe text of this recommended practice. Clause 4 presents parameters related to electrical performance of apower distribution subsystems, including parame

49、ter denitions, test methods, and test conditions. Each testmethod is the recommended method of testing a given parameter, and the test condition denes the range ofvalues for test variables that are essential to the test.Clause 5 collects common parameters related to reliability, maintainability, environmental parameters, andmechanical aspects of a power subsystem. Reliability and environmental parameters are crucial for a powersubsystem to operate reliably, but they are out of the realm of electrical engineering. Hence, only denitionsa