IEC 61300-2-5-2009 Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-5 Tests - Torsion《纤维光学互连器件和无源元件.基本试验和测量程序.第2-5部分 试验.扭矩》.pdf

《IEC 61300-2-5-2009 Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-5 Tests - Torsion《纤维光学互连器件和无源元件.基本试验和测量程序.第2-5部分 试验.扭矩》.pdf》由会员分享，可在线阅读，更多相关《IEC 61300-2-5-2009 Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-5 Tests - Torsion《纤维光学互连器件和无源元件.基本试验和测量程序.第2-5部分 试验.扭矩》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC 61300-2-5 Edition 3.0 2009-01 INTERNATIONAL STANDARD Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 2-5: Tests Torsion IEC 61300-2-5:2009(E) THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2009 IEC, Geneva, Switzerland All rights reserved

2、. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you

3、 have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee for further information. IEC Central Office 3, rue de Varemb CH-1211 Geneva 20 Switzerland Email: inmailiec.c

4、h Web: www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and related technologies. About IEC publications The technical content of IEC publications is kept

5、 under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. Catalogue of IEC publications: www.iec.ch/searchpub The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technica

6、l committee,). It also gives information on projects, withdrawn and replaced publications. IEC Just Published: www.iec.ch/online_news/justpub Stay up to date on all new IEC publications. Just Published details twice a month all new publications released. Available on-line and also by email. Electrop

7、edia: www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical Vocabulary online. Customer Serv

8、ice Centre: www.iec.ch/webstore/custserv If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service Centre FAQ or contact us: Email: csciec.ch Tel.: +41 22 919 02 11 Fax: +41 22 919 03 00 IEC 61300-2-5 Edition 3.0 2009-01 INTERNATIONAL STAN

9、DARD Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 2-5: Tests Torsion INTERNATIONAL ELECTROTECHNICAL COMMISSION J ICS 33.180.20 PRICE CODE ISBN 2-8318-1022-9 Registered trademark of the International Electrotechnical Commission 2 61300-2-5 IEC:

10、2009(E) CONTENTS FOREWORD.3 1 Scope.5 2 Normative references .5 3 General description 5 4 Apparatus.5 4.1 General .5 4.2 Mounting fixture 6 4.3 Cable clamp 6 4.4 Weights.6 4.5 Optical source and detector.7 5 Procedure 7 5.1 Preparation of specimens7 5.2 Pre-conditioning 7 5.3 Mount the device under

11、test 7 5.4 Measure the attenuation7 5.5 Apply cable load7 5.6 Measure the attenuation7 5.7 Twist the cable 7 5.8 Test pressure 7 5.9 Monitoring attenuation.8 5.10 Final measurements and examinations8 6 Severity8 7 Details to be specified 9 Figure 1 Component or device test set-up6 Figure 2 Closure t

12、est set-up.6 Table 1 Severity levels.8 61300-2-5 IEC:2009(E) 3 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE COMPONENTS BASIC TEST AND MEASUREMENT PROCEDURES Part 2-5: Tests Torsion FOREWORD 1) The International Electrotechnical Commission (IEC) is a wor

13、ldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other

14、activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the sub

15、ject dealt with may participate in this preparatory work. International, governmental and non- governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions d

16、etermined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Co

17、mmittees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in wh

18、ich they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Public

19、ation and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any equipment declared to be in conformity with an IEC Publication. 6) All users should ensure t

20、hat they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any n

21、ature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referen

22、ced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. Internat

23、ional Standard IEC 61300-2-5 has been prepared by subcommittee 86B: Fibre optic interconnecting devices and passive components, of IEC technical committee 86: Fibre optics. This third edition cancels and replaces the second edition, published in 2002 and constitutes a technical revision. Specific te

24、chnical changes from the previous edition are as follows: the title was changed; the procedure was reconsidered; the figure of closure test set-up was added; the severity of the test was reconsidered according to the component. 4 61300-2-5 IEC:2009(E) The text of this standard is based on the follow

25、ing documents: FDIS Report on voting 86B/2774/FDIS 86B/2806/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. A list of all parts

26、 of IEC 61300 series, published under the general title Fibre optic interconnecting devices and passive components Basic test and measurement procedures can be found on the IEC website. The committee has decided that the contents of this publication will remain unchanged until the maintenance result

27、 date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. A bilingual version of this publication may be issued at a later date. 61300-2-5

28、 IEC:2009(E) 5 FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE COMPONENTS BASIC TEST AND MEASUREMENT PROCEDURES Part 2-5: Tests Torsion 1 Scope The purpose of this part of IEC 61300 is to determine the ability of the cable attachment element of the device under test to withstand torsional loads, whi

29、le under tension, as might be experienced during installation and normal service. The scope of the test also includes those elements designed for ribbon cables. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, onl

30、y the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 61300-1, Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 1: General guidance IEC 61300-3-1, Fibre optic int

31、erconnecting devices and passive components Basic test and measurement procedures Part 3-1: Examinations and measurements Visual examination IEC 61300-3-3, Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 3-3: Examinations and measurements Active

32、monitoring of changes in attenuation and return loss IEC 61300-3-4, Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 3-4: Examinations and measurements Attenuation IEC 61300-3-6, Fibre optic interconnecting devices and passive components Basic tes

33、t and measurement procedures Part 3-6: Examinations and measurements Return loss 3 General description The cable-to-device interface, while under a specified tension, is subjected to a torsional load or twisting action to determine the effects of this action on the physical and optical properties of

34、 the device. 4 Apparatus 4.1 General The test apparatus shall be capable of applying simultaneously both tension and a torsional load or twisting action to the cable-to-device interface. Figures 1 and 2 show the basic parts of a test apparatus for component and closure test set-ups, respectively. 6

35、61300-2-5 IEC:2009(E) 4.2 Mounting fixture Use a fixture to rigidly mount the device under test and hold it in proper alignment throughout the test. The fixture shall allow the device under test to be connected to an optical source and detector for monitoring attenuation. 4.3 Cable clamp The cable c

36、lamp is the point at which the torsional load is applied. The cable clamp shall be capable of grasping and securing the cable so that it does not turn or slip in the holder when loads are applied. The clamp shall not crush the optical fibres or cause a change in the attenuation. The cable clamp may

37、consist of a mandrel around which several turns of cable are wrapped and secured. 4.4 Weights Weights or another mechanism for applying a tensile load to the cable clamp are required. Values of recommended loads are given in Table 1. 400 mm-1 000 mm (See 5.3) To optical source Mounting fixture (secu

38、re to prevent movement) Weights, if specified Cable clamp (should facilitate addition of weights if specified) To optical detector Device under test Twist in both directions IEC 2300/08 Figure 1 Component or device test set-up Closure 1 3 Sample fixation Clamping distance 4 Cable seal Cable 2 IEC 23

39、01/08 Figure 2 Closure test set-up 61300-2-5 IEC:2009(E) 7 4.5 Optical source and detector The optical source and detector used to measure changes in attenuation shall comply with that specified in IEC 61300-3-4. 5 Procedure 5.1 Preparation of specimens Prepare the specimens according to the manufac

40、turers instructions or as specified in the relevant specification. The device under test shall be terminated onto a sufficient length of fibre cable to facilitate interfacing with the optical source and detector. 5.2 Pre-conditioning Pre-condition the device under test for 2 h at the standard test c

41、onditions specified in IEC 61300-1, unless otherwise specified in the relevant specification. Measure and record the attenuation of the device under test. 5.3 Mount the device under test The body of the specimen shall be rigidly mounted to a holding plate which is secured in a fixed position (see Fi

42、gure 1). The clamp to which the load can be applied shall be fastened to the cable in such a manner that the optical fibre or cable is not crushed. The top of the cable clamp shall be 400 mm from the end of the strain relief, if used (see Figure 1). For cable diameters larger than 25 mm, the top of

43、the cable clamp shall be 1 000 mm from the end of the strain relief. If there is no strain relief, the end of the specimen nearest the cable clamp shall be the reference. 5.4 Measure the attenuation Re-measure the attenuation to ensure that the fixturing and cable clamping have not affected the cabl

44、es attenuation. 5.5 Apply cable load Gradually apply the tensile load, as recommended in Table 1 or as specified in the relevant specification, to the cable clamping fixture, being careful to avoid any sudden jerking or straining of the cable. 5.6 Measure the attenuation After the load is applied, r

45、e-measure the attenuation of the specimen. This value shall be recorded and used as a reference to determine the effects of the twisting motion. 5.7 Twist the cable Apply a twisting motion to the cable-clamping device, being careful to control the vertical and horizontal motion of the load. One twis

46、t cycle shall consist of a twist angle (as indicated in Table 1 or in the relevant specification) in one direction, a return to the original position, a twist angle (as indicatead in Table 1 or in the relevant specification) in the opposite direction and a final return to the original position. Repe

47、at the twist cycle as many times as specified in Table 1, or in the relevant specification. 5.8 Test pressure For Category S closures, use a test pressure: 40 kPa 2 kPa over-pressure at test temperature. For products used in pressurized networks, all testing should be carried out at 98,0 kPa 9,8 kPa

48、 over-pressure instead of 40 kPa over-pressure. 8 61300-2-5 IEC:2009(E) 5.9 Monitoring attenuation The attenuation of the specimen shall be monitored during the test, as described in IEC 61300-3-3, unless otherwise specified in the relevant specification. Any deviation in the device attenuation from

49、 that measured in IEC 61300-3-6 shall be considered attributable to the cable/device interface, fibre-to-fibre interfaces or fibre-to-source/detector interfaces in the device. NOTE If there are unacceptable changes in attenuation and it is questionable whether the cable itself may be at fault, a control test to determine cable contribution shall be performed in the same manner using a piece of cable and two cable clamps. 5.10 Final mea