IEC 60317-57-2010 Specifications for particular types of winding wires - Part 57 Polyamide-imide enamelled round copper wire class 220《特种绕组线规格.第57部分 220级聚酰胺-酰亚胺漆包圆铜线 n》.pdf

《IEC 60317-57-2010 Specifications for particular types of winding wires - Part 57 Polyamide-imide enamelled round copper wire class 220《特种绕组线规格.第57部分 220级聚酰胺-酰亚胺漆包圆铜线 n》.pdf》由会员分享，可在线阅读，更多相关《IEC 60317-57-2010 Specifications for particular types of winding wires - Part 57 Polyamide-imide enamelled round copper wire class 220《特种绕组线规格.第57部分 220级聚酰胺-酰亚胺漆包圆铜线 n》.pdf（22页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC 60317-57 Edition 1.0 2010-08 INTERNATIONAL STANDARD NORME INTERNATIONALE Specifications for particular types of winding wires Part 57: Polyamide-imide enamelled round copper wire, class 220 Spcifications pour types particuliers de fils de bobinage Partie 57: Fil de section circulaire en cuivre

2、maill avec polyamide-imide, classe 220 IEC 60317-57:2010 THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2010 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, i

3、ncluding photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address bel

4、ow or your local IEC member National Committee for further information. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopie e

5、t les microfilms, sans laccord crit de la CEI ou du Comit national de la CEI du pays du demandeur. Si vous avez des questions sur le copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national de la CEI

6、 de votre pays de rsidence. IEC Central Office 3, rue de Varemb CH-1211 Geneva 20 Switzerland Email: inmailiec.ch Web: www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrica

7、l, electronic and related technologies. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. Catalogue of IEC publications: www.iec.ch/sear

8、chpub The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, withdrawn and replaced publications. IEC Just Published: www.iec.ch/online_news/justpub Stay up to date on all new IEC publications. J

9、ust Published details twice a month all new publications released. Available on-line and also by email. Electropedia: www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions in English and French, with equivalent

10、terms in additional languages. Also known as the International Electrotechnical Vocabulary online. Customer Service Centre: www.iec.ch/webstore/custserv If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service Centre FAQ or contact us: Em

11、ail: csciec.ch Tel.: +41 22 919 02 11 Fax: +41 22 919 03 00 A propos de la CEI La Commission Electrotechnique Internationale (CEI) est la premire organisation mondiale qui labore et publie des normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A

12、propos des publications CEI Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Catalogue des publications de la CEI: www.iec.ch/searchpub/cur_fut-f.htm Le Catalogue en-l

13、igne de la CEI vous permet deffectuer des recherches en utilisant diffrents critres (numro de rfrence, texte, comit dtudes,). Il donne aussi des informations sur les projets et les publications retires ou remplaces. Just Published CEI: www.iec.ch/online_news/justpub Restez inform sur les nouvelles p

14、ublications de la CEI. Just Published dtaille deux fois par mois les nouvelles publications parues. Disponible en-ligne et aussi par email. Electropedia: www.electropedia.org Le premier dictionnaire en ligne au monde de termes lectroniques et lectriques. Il contient plus de 20 000 termes et dfinitio

15、ns en anglais et en franais, ainsi que les termes quivalents dans les langues additionnelles. Egalement appel Vocabulaire Electrotechnique International en ligne. Service Clients: www.iec.ch/webstore/custserv/custserv_entry-f.htm Si vous dsirez nous donner des commentaires sur cette publication ou s

16、i vous avez des questions, visitez le FAQ du Service clients ou contactez-nous: Email: csciec.ch Tl.: +41 22 919 02 11 Fax: +41 22 919 03 00 60317-57 Edition 1.0 2010-08 INTERNATIONAL STANDARD NORME INTERNATIONALE Specifications for particular types of winding wires Part 57: Polyamide-imide enamelle

17、d round copper wire, class 220 Spcifications pour types particuliers de fils de bobinage Partie 57: Fil de section circulaire en cuivre maill avec polyamide-imide, classe 220 INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE J ICS 29.60.10 PRICE CODE CODE PRIX ISBN

18、 978-2-88912-142-7 Registered trademark of the International Electrotechnical Commission Marque dpose de la Commission Electrotechnique Internationale 2 60317-57 IEC:2010 CONTENTS FOREWORD.3 INTRODUCTION.5 1 Scope.6 2 Normative references .6 3 Definitions, general notes on methods of test and appear

19、ance .6 3.1 Definitions and general notes on methods of test 6 3.2 Appearance.6 4 Dimensions 6 5 Electrical resistance .7 6 Elongation 7 7 Springiness 7 8 Flexibility and adherence7 9 Heat shock .7 10 Cut-through 7 11 Resistance to abrasion .7 12 Resistance to solvents8 13 Breakdown voltage .8 14 Co

20、ntinuity of insulation .8 15 Temperature index .8 16 Resistance to refrigerants.8 17 Solderability .8 18 Heat bonding9 19 Dielectric dissipation factor.9 20 Resistance to transformer oil9 21 Loss of mass 9 22 High temperature failure.9 23 Pin hole test .9 30 Packaging 9 Table 1 Resistance to abrasio

21、n8 60317-57 IEC:2010 3 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES Part 57: Polyamide-imide enamelled round copper wire, class 220 FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comp

22、rising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Stan

23、dards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this prep

24、aratory work. International, governmental and non- governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organ

25、izations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form

26、of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretati

27、on by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regi

28、onal publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out

29、by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees

30、for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the N

31、ormative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held re

32、sponsible for identifying any or all such patent rights. International Standard IEC 60317-57 has been prepared by IEC technical committee 55: Winding wires. The text of this standard is based on the following documents: CDV Report on voting 55/1137/CDV 55/1167A/RVC Full information on the voting for

33、 the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. This standard is to be read in conjunction with IEC 60317-0-1 (2008). 4 60317-57 IEC:2010 The numbering of clauses in

34、 this standard is not continuous from Clauses 23 to 30 in order to reserve space for possible future wire requirements prior to those for wire packaging. A list of all the parts in the IEC 60317 series, under the general title Specifications for particular types of winding wires, can be found on the

35、 IEC website. The committee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, repl

36、aced by a revised edition, or amended. 60317-57 IEC:2010 5 INTRODUCTION This part of IEC 60317 is one of a series which deals with insulated wires used for windings in electrical equipment. The series has three groups describing 1) test methods (IEC 60851); 2) specifications for particular types of

37、winding wire (IEC 60317); 3) packaging of winding wires (IEC 60264). 6 60317-57 IEC:2010 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES Part 57: Polyamide-imide enamelled round copper wire, class 220 1 Scope This part of IEC 60317 specifies the requirements of an enamelled round copper winding

38、 wire of class 220 with a sole coating based on polyamide-imide resin, which may be modified providing it retains the chemical identity of the original resin and meets all specified wire requirements. Class 220 is a thermal class that requires a minimum temperature index of 220 and a heat shock temp

39、erature of at least 240 C. The temperature in degrees Celsius corresponding to the temperature index is not necessarily that at which it is recommended that the wire be operated and this will depend on many factors, including the type of equipment involved. The range of nominal conductor diameters c

40、overed by this standard is as follows: Grade 1: 0,071 mm up to and including 1,600 mm; Grade 2: 0,071 mm up to and including 1,600 mm. The nominal conductor diameters are specified in Clause 4 of IEC 60317-0-1. 2 Normative references The following referenced documents are indispensable for the appli

41、cation of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60317-0-1:2008, Specifications for particular types of winding wires Part 0-1: General requirements Enamelled r

42、ound copper wire 3 Definitions, general notes on methods of test and appearance 3.1 Definitions and general notes on methods of test For definitions and general notes on methods of test, see Clause 3 of IEC 60317-0-1. In case of inconsistencies between IEC 60317-0-1 and this standard, IEC 60317-57 s

43、hall prevail. 3.2 Appearance See Subclause 3.3 of IEC 60317-0-1. 4 Dimensions See Clause 4 of IEC 60317-0-1. 60317-57 IEC:2010 7 5 Electrical resistance See Clause 5 of IEC 60317-0-1. 6 Elongation See Clause 6 of IEC 60317-0-1. 7 Springiness See Clause 7 of IEC 60317-0-1. 8 Flexibility and adherence

44、 See Clause 8 of IEC 60317-0-1, where the constant K used for the calculation of the number of revolutions for the peel test shall be 75 mm. 9 Heat shock See Clause 9 of IEC 60317-0-1, where the minimum heat shock temperature shall be 240 C. 10 Cut-through No failure shall occur within 2 min at 350

45、C. 11 Resistance to abrasion (nominal conductor diameters from 0,250 mm up to and including 1,600 mm) The wire shall meet the requirements given in Table 1. 8 60317-57 IEC:2010 Table 1 Resistance to abrasion Grade 1 Grade 2 Nominal conductor diameter mm Minimum average force to failure N Minimum for

46、ce to failure of each measurement N Minimum average force to failure N Minimum force to failure of each measurement N 0,250 0,280 0,315 0,355 0,400 3,00 3,25 3,50 3,75 4,05 2,55 2,75 2,95 3,20 3,45 4,90 5,25 5,65 6,05 6,50 4,15 4,45 4,80 5,15 5,50 0,450 0,500 0,560 0,630 0,710 4,35 4,65 5,00 5,35 5,

47、70 3,70 3,95 4,25 4,55 4,85 7,00 7,50 5,90 6,35 0,800 0,900 1,000 1,120 1,250 6,10 6,55 7,05 7,60 8,20 5,15 5,55 5,95 6,45 6,95 1,400 1,600 8,80 9,45 7,45 8,00 For intermediate nominal conductor diameters, the value of the next largest nominal conductor diameter shall be taken. 12 Resistance to solv

48、ents See Clause 12 of IEC 60317-0-1. 13 Breakdown voltage See Clause 13 of IEC 60317-0-1, where the elevated temperature is 220C. 14 Continuity of insulation See Clause 14 of IEC 60317-0-1. 15 Temperature index See Clause 15 of IEC 60317-0-1, where the minimum temperature index shall be 220. 16 Resi

49、stance to refrigerants Test appropriate but no requirements specified. 17 Solderability Test inappropriate. 60317-57 IEC:2010 9 18 Heat bonding Test inappropriate. 19 Dielectric dissipation factor Test inappropriate. 20 Resistance to transformer oil Test appropriate but no requirements specified. 21 Loss of mass Test inappropriate. 22 High temperature failur