SAE AS 81969 25-2015 INSTALLING AND REMOVAL TOOLS CONNECTOR ELECTRICAL CONTACT TYPE III CLASS 2 COMPOSITION C.pdf

《SAE AS 81969 25-2015 INSTALLING AND REMOVAL TOOLS CONNECTOR ELECTRICAL CONTACT TYPE III CLASS 2 COMPOSITION C.pdf》由会员分享，可在线阅读，更多相关《SAE AS 81969 25-2015 INSTALLING AND REMOVAL TOOLS CONNECTOR ELECTRICAL CONTACT TYPE III CLASS 2 COMPOSITION C.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、 AEROSPACE STANDARD INSTALLING AND REMOVAL TOOLS, CONNECTOR, ELECTRICAL CONTACT, TYPE III, CLASS 2, COMPOSITION C AS81969/25Copyright 2015 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, e

2、lectronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED

3、2015-08THIRD ANGLE PROJECTION CUSTODIAN: AE-8/AE-8C2 FEDERAL SUPPLY CLASS 5120 AS81969/25 SHEET 1 OF 3 PROCUREMENT SPECIFICATION: AS81969 SAETechnicalStandardsBoard Rulesprovidethat:“Thisreportispublished bySAEto advance the state oftechnicaland engineering sciences.The use ofthisreportisentirelyvol

4、untary,anditsapplicabilityandsuitabilityforanyparticularuse,includinganypatentinfringementarising therefrom,isthe sole responsibilityoftheuser.”SAEreviewseachtechnicalreportatleasteveryfiveyearsatwhich time itmaybe revised,reaffirmed,stabilized, orcancelled.SAEinvitesyourwritten commentsandsuggestio

5、ns.SAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/AS81969/25 RATIONALE THIS DETAIL SPECIFICATION SHEET IS REQUIRED TO ALLOW THE CANCELLATION AND SUPERSESSION OF MIL-I-81969/25 WITH THIS DOCUMENT, TO IMPROVE DRAWING LEGIBILITY,

6、TO UPDATE QUALIFICATION INFORMATION, TO REMOVE GOVERNMENT JARGON, AND TO UPDATE REFERENCES. NOTICE THE COMPLETE REQUIREMENTS FOR PROCURING THE PRODUCT DESCRIBED HEREIN SHALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE OF AS81969. FIGURE 1 - INSTALLING AND REMOVAL TOOL CONFIGURATIONS/DIMENSIONS AER

7、OSPACE STANDARD AS81969/25 SHEET 2 OF 3 INSTALLING AND REMOVAL TOOLS, CONNECTOR, ELECTRICAL CONTACT, TYPE III, CLASS 2, COMPOSITION C TABLE 1 - METRIC EQUIVALENTS INCHES MILLIMETERS INCHES MILLIMETERS INCHES MILLIMETERS .020 0.025 .74 0.762 1.300 10.16 .030 0.051 .88 1.27 3.50 10.62 TABLE 2 - FIGURE

8、 1 CONFIGURATION/DIMENSIONS DASH NUMBER CONNECTOR TYPE(S) A DIA. B DIA. C ANGLE +/-0 30 D E DIA. L MAX. -01 BNC/TNC .625 (15.88) .600 (15.24) 10 0 .330 ( 8.38) .527 (13.39) 12.00 (304.80) -02 BNC/TNC .625 (15.88) .600 (15.24) 10 0 .330 ( 8.38) .527 (13.39) 6.00 (152.40) -03 N .875 (22.23) .850 (21.5

9、9) 8 0 .500 (12.70) .777 (19.74) 12.00 (304.80) -04 N .875 (22.23) .850 (21.59) 8 0 .500 (12.70) .777 (19.74) 6.00 (152.40) -05 TPS .531 (13.49) .470 (11.94) 8 0 .312 ( 7.92) .442 (11.23) 12.00 (304.80) -06 TPS .531 (13.49) .470 (11.94) 8 0 .312 ( 7.92) .442 (11.23) 6.00 (152.40) REQUIREMENTS: ALL R

10、EQUIREMENTS SHALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE OF AS81969. 1. DESIGN: THE TOOL SHALL BE DESIGNED IN ACCORDANCE WITH FIGURE 1 AND TABLE 1. DIMENSIONS ARE IN INCHES AND APPLY AFTER PLATING WHERE PLATING IS APPLICABLE. METRIC EQUIVALENTS IN TABLE 1 ARE GIVEN FOR GENERAL INFORMATION ONL

11、Y AND ARE BASED ON 1 INCH = 25.4 MILLIMETERS. UNLESS OTHERWISE SPECIFIED, TOLERANCE IS .003 INCH (0.08 MILLIMETERS). STAMP AND WHITE FILL, LETTERING HEIGHT .08 (2.0 MILLIMETERS). REMOVE ALL BURRS AND SHARP EDGES. 2. MATERIAL AND FINISHES: HANDLE - PLASTIC PER L-P-410 OR APPROVED EQUIVALENT. SHAFT -

12、TYPE 304, CRES, PER MIL-T-8504, DASH NUMBERS -01 AND -02 ARE TO BE 18 GAGE, .049 (1.24 MILLIMETERS) WALL THICKNESS, DASH NUMBERS -03 THROUGH -06 ARE TO BE 16 GAGE, .065 (1.65 MILLIMETERS) WALL THICKNESS. COLLET - TYPE 304 CRES, PER MIL-T-8504, DASH NUMBERS -01 AND -02 ARE TO BE 18 GAGE, .049 (1.24 M

13、ILLIMETERS) WALL THICKNESS, DASH NUMBERS -03 THROUGH -06 ARE TO BE 16 GAGE, .065 (1.65 MILLIMETERS) WALL THICKNESS. 3. PART NUMBER/MARKING: SEE EXAMPLE BELOW M81969 /25 -01 BASE SPECIFICATION DETAIL SHEET DASH NUMBER EACH TOOL SHALL BE LEGIBLY AND PERMANENTLY MARKED ON THE HANDLE WITH THE MANUFACTUR

14、ERS IDENTIFICATION AND PART NUMBER IN ACCORDANCE WITH MIL-STD-130. MANUFACTURER SYMBOL, IF USED, SHALL BE IN ACCORDANCE WITH AIR1351. 4. QUALIFICATION: QUALIFICATION SHALL BE IN ACCORDANCE WITH AS81969 WITH THE FOLLOWING EXCEPTIONS: PLUNGER FORCE - NOT APPLICABLE ALTERNATIVE QUALIFICATION REQUIREMEN

15、TS SUCH AS CERTIFICATION, FIRST ARTICLE OR QC TESTING MAY BE IMPOSED BY THE QUALIFYING ACTIVITY (QA). THE QA SHALL SUBMIT A WRITTEN REQUEST TO THE AE-8C2 COMMITTEE FOR REVIEW AND APPROVAL OF THE ALTERNATIVE QUALIFICATION TESTING PROGRAM PRIOR TO IMPLEMENTATION OF THE REQUIREMENT. AEROSPACE STANDARD

16、AS81969/25 SHEET 3 OF 3 INSTALLING AND REMOVAL TOOLS, CONNECTOR, ELECTRICAL CONTACT, TYPE III, CLASS 2, COMPOSITION C APPLICATION NOTES: 1. THIS TOOL SHALL BE USED TO INSTALL AND REMOVE CONNECTORS COVERED BY THE FOLLOWING DASH NUMBERS: -01 THROUGH -04 SERIES BNC, TNC AND N CONNECTORS SPECIFIED IN MI

17、L-PRF-39012. -05 AND -06 SERIES TPS CONNECTORS SPECIFIED IN MIL-DTL-55235. 2. THIS DOCUMENT SUPERSEDES MIL-I-81969/25 DATED 14 APRIL 1977. SPECIFICATION NOTES: 1. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL

18、 CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.