REG NASA-LLIS-1803--2007 Lessons Learned CSAM Augments X-Ray Inspection of Die Attach (MRO Ka-Band Anomaly).pdf

《REG NASA-LLIS-1803--2007 Lessons Learned CSAM Augments X-Ray Inspection of Die Attach (MRO Ka-Band Anomaly).pdf》由会员分享，可在线阅读，更多相关《REG NASA-LLIS-1803--2007 Lessons Learned CSAM Augments X-Ray Inspection of Die Attach (MRO Ka-Band Anomaly).pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、Lessons Learned Entry: 1803Lesson Info:a71 Lesson Number: 1803a71 Lesson Date: 2007-7-31a71 Submitting Organization: JPLa71 Submitted by: David Oberhettingera71 POC Name: Eric Archer (Supervisor, Spacecraft Transponders)a71 POC Email: Eric.D.Archerjpl.nasa.gova71 POC Phone: 818-354-7350Subject: CSAM

2、 Augments X-Ray Inspection of Die Attach (MRO Ka-Band Anomaly) Abstract: An in-flight failure of a hybrid amplifier used to derive the Ka-band downlink signal for Mars Reconnaissance Orbiter suggests that X-ray screening alone may not be adequate to determine the quality of coverage of the eutectic

3、die attach. CSAM is a non-destructive internal inspection technique that can complement high resolution X-rays by isolating variations in material properties. When screening RF hybrids and other critical components, consider the use of CSAM to augment high resolution X-ray inspection.Description of

4、Driving Event: After 6000 hours of nearly continuous in-flight operation aboard Mars Reconnaissance Orbiter (MRO), the Ka-band circuitry in the primary Small Deep Space Transponder (SDST-1) experienced an abrupt increase in power consumption. It abruptly decreased three hours later, permanently disa

5、bling the Ka-band downlink (References (1) and (2). This was likely due to an internal short circuit within the metal-semiconductor field-effect transistor (MESFET) hybrid amplifier used to derive the Ka-band signal within the SDST, which in turn raised the junction temperature and caused an open ci

6、rcuit in the hybrid. The X-band hybrid amplifier in SDST-1, as well as the X-band hybrid amplifier in the backup SDST-2, may also have been overstressed. A possible cause of the short circuit is a poor or failed eutectic bond between the hybrid device and the copper-molybdenum carrier. The process o

7、f mounting a semiconductor die/chip to a substrate or package is known as die attach. Methods include eutectic bonding (soldering) on ceramic or metal Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-substrates, adhesive bonding, and glass bonding. Ho

8、wever, soldering is preferred for high power devices because of its good thermal/electrical conductivity and ability to accommodate thermal expansion. A eutectic bond is formed by heating two or more materials in a joint such that they diffuse together to form a (eutectic) alloy. Manufacturing techn

9、ology has not eliminated voids and disbonds in the bonding layers that can increase the likelihood of die cracking, increase the chip operating temperature, and weaken the die bonds. This hybrid device failure mode is a risk for other SDST builds, and some flight hardware for the Kepler and Juno mis

10、sions may be replaced. The primary method for non-destructive evaluation (NDE) of die attach fabrication is high resolution X-rays. Following the MRO failure, the eutectic (AuSn solder) bond X-rays used to screen the parts were reexamined and revealed no voids between the die and the package (Refere

11、nce (3). Subsequently, JPL employed an ultrasound inspection technique known as C-mode Scanning Acoustic Microscopy (CSAM). Unlike X-rays, which depict the integrated density of material between the X-ray source and detector, CSAM technology can examine a specific layer. This distinction is particul

12、arly important when looking for disbonding defects such as non-wetting of surfaces or delamination. Figure 1 is an X-ray of a spare MRO hybrid die; it shows 3 void areas on the left side of the chip, as well as an unfilled via, but does not show areas of poor die attach. In the corresponding CSAM im

13、age (Figure 2), the 3 large void areas are clearly visible, as well as some smaller ones. The CSAM ultrasound image provides enough detail that, after conversion to a digital image (Figure 3), a more quantitative assessment can be performed that states the total area of disbonds and voids as a perce

14、ntage of the total die area. Figure 1 is a grayscale image of a rectangular die attach. Thirteen filled vias scattered across the die appear as small black circles, and a single unfilled via appears as a white circle. Between the faintly visible traces are three shadowy ovals that are apparently voi

15、ds.Figure 1. Microfocus X-ray of hybrid amplifier die (S/N D209) with lid Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Figure 2 is a grayscale image that is clearly the same rectangular die attach. This CSAM image is somewhat grainier, but it show

16、s the voids in great detail and high contrast, and apparent textures are visible in portions of the image that may represent material characteristics of the layer. Now you can tell that there are three large voids with an area of perhaps 3 percent of the total area of the die, plus a few additional

17、very small voids.Figure 2. CSAM image of hybrid amplifier die (S/N D209) with lid Figure 3 is also a grayscale image of a different but similar die, except a center rectangle within the grayscale appears as a binary image- each pixel is either completely black or it is white- of that portion of the

18、die. Two small white rectangles have been overlaid on the image to draw attention to areas of interest, and one of the rectangles surrounds a small white dot (that fills about one-tenth of the rectangle).Figure 3. Binary image converted from a CSAM image of hybrid amplifier die (S/N D221). The white

19、 boxes identify the most critical (i.e., the FET active) regions The MRO failure investigation suggests that to assure adequate NDE of critical flight hardware, die attach X-rays may need to be supplemented with acoustic images. X-ray imagery can determine that the proper amount of AuSn solder is pr

20、esent between the die and the carrier, but it cannot determine whether the solder has actually wetted the surfaces. Where there is a complete lack of solder, (i.e., a void) the two imaging methods should give similar results. References: (1) “Transponder DC input current and power increased for 3 ho

21、urs on DOY 14,“ Jet Propulsion Laboratory Incident Surprise Anomaly No. Z88615, May 31, 2006. (2) “SDST - 3 Hour Power Surge,“ Jet Propulsion Laboratory Problem/Failure Report No. Z88763, June 30, 2006. (3) MRO Small Deep Space Transponder Ka-Band Exciter Anomaly Final Report, Jet Propulsion Laborat

22、ory Document No. JPL D-31195, March 16, 2007.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Lesson(s) Learned: For critical flight hardware, the current X-ray process for screening RF hybrids may not be adequate to determine the quality of coverage

23、of the eutectic die attach. CSAM is a non-destructive internal inspection technique that can complement high resolution X-rays by isolating variations in material properties. CSAM detects the extent of air space-type physical defects in components, including cracks, voids, delaminations, and porosit

24、y, that occur during manufacturing, environmental test, and operation.Recommendation(s): When screening RF hybrids and other complex RF parts, consider the use of CSAM to augment high resolution X-ray inspection.Evidence of Recurrence Control Effectiveness: JPL has referenced this lesson learned as

25、additional rationale and guidance supporting Paragraph 4.5.3.1 (“Telecommunications System Design: Telemetry Links Spacecraft Downlink RF Carrier“) and Paragraph 4.12.2.1 (“Flight Electronics Hardware System Design: Electronic Packaging Qualification of Electronic Packaging Designs“) in the JPL stan

26、dard “Design, Verification/Validation and Operations Principles for Flight Systems (Design Principles),“ JPL Document D-17868, Rev. 3, December 11, 2006. This lesson also supports Paragraph 7.5.4 (“Safety and Mission Assurance Practices: Electronic Parts Reliability, Application, and Acquisition“) i

27、n the Jet Propulsion Laboratory standard “Flight Project Practices, Rev. 6,“ JPL DocID 58032, March 6, 2006.Documents Related to Lesson: Click here to download document. Mission Directorate(s): a71 Space Operationsa71 Sciencea71 Exploration SystemsAdditional Key Phrase(s): a71 Program Management.Ris

28、k managementProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-a71 Systems Engineering and Analysis.a71 Systems Engineering and Analysis.Planning of requirements verification processesa71 Engineering Design (Phase C/D).a71 Engineering Design (Phase C/D)

29、.Spacecraft and Spacecraft Instrumentsa71 Manufacturing and Assemblya71 Safety and Mission Assurance.Early requirements and standards definitiona71 Safety and Mission Assurance.Product Assurancea71 Safety and Mission Assurance.Qualitya71 Safety and Mission Assurance.Reliabilitya71 Additional Categor

30、ies.Communication Systemsa71 Additional Categories.Flight Equipmenta71 Additional Categories.Flight Operationsa71 Additional Categories.Hardwarea71 Additional Categories.Industrial Operationsa71 Additional Categories.Parts, Materials, & Processesa71 Additional Categories.Payloadsa71 Additional Categ

31、ories.Risk Management/Assessmenta71 Additional Categories.Safety & Mission Assurancea71 Additional Categories.Spacecrafta71 Additional Categories.Test & VerificationAdditional Info: a71 Project: Mars Reconnaissance OrbiterApproval Info: a71 Approval Date: 2007-10-30a71 Approval Name: ghendersona71 Approval Organization: HQProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-