欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    REG NASA-LLIS-1803--2007 Lessons Learned CSAM Augments X-Ray Inspection of Die Attach (MRO Ka-Band Anomaly).pdf

    • 资源ID:1019297       资源大小:20.52KB        全文页数:5页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    REG NASA-LLIS-1803--2007 Lessons Learned CSAM Augments X-Ray Inspection of Die Attach (MRO Ka-Band Anomaly).pdf

    1、Lessons Learned Entry: 1803Lesson Info:a71 Lesson Number: 1803a71 Lesson Date: 2007-7-31a71 Submitting Organization: JPLa71 Submitted by: David Oberhettingera71 POC Name: Eric Archer (Supervisor, Spacecraft Transponders)a71 POC Email: Eric.D.Archerjpl.nasa.gova71 POC Phone: 818-354-7350Subject: CSAM

    2、 Augments X-Ray Inspection of Die Attach (MRO Ka-Band Anomaly) Abstract: An in-flight failure of a hybrid amplifier used to derive the Ka-band downlink signal for Mars Reconnaissance Orbiter suggests that X-ray screening alone may not be adequate to determine the quality of coverage of the eutectic

    3、die attach. CSAM is a non-destructive internal inspection technique that can complement high resolution X-rays by isolating variations in material properties. When screening RF hybrids and other critical components, consider the use of CSAM to augment high resolution X-ray inspection.Description of

    4、Driving Event: After 6000 hours of nearly continuous in-flight operation aboard Mars Reconnaissance Orbiter (MRO), the Ka-band circuitry in the primary Small Deep Space Transponder (SDST-1) experienced an abrupt increase in power consumption. It abruptly decreased three hours later, permanently disa

    5、bling the Ka-band downlink (References (1) and (2). This was likely due to an internal short circuit within the metal-semiconductor field-effect transistor (MESFET) hybrid amplifier used to derive the Ka-band signal within the SDST, which in turn raised the junction temperature and caused an open ci

    6、rcuit in the hybrid. The X-band hybrid amplifier in SDST-1, as well as the X-band hybrid amplifier in the backup SDST-2, may also have been overstressed. A possible cause of the short circuit is a poor or failed eutectic bond between the hybrid device and the copper-molybdenum carrier. The process o

    7、f mounting a semiconductor die/chip to a substrate or package is known as die attach. Methods include eutectic bonding (soldering) on ceramic or metal Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-substrates, adhesive bonding, and glass bonding. Ho

    8、wever, soldering is preferred for high power devices because of its good thermal/electrical conductivity and ability to accommodate thermal expansion. A eutectic bond is formed by heating two or more materials in a joint such that they diffuse together to form a (eutectic) alloy. Manufacturing techn

    9、ology has not eliminated voids and disbonds in the bonding layers that can increase the likelihood of die cracking, increase the chip operating temperature, and weaken the die bonds. This hybrid device failure mode is a risk for other SDST builds, and some flight hardware for the Kepler and Juno mis

    10、sions may be replaced. The primary method for non-destructive evaluation (NDE) of die attach fabrication is high resolution X-rays. Following the MRO failure, the eutectic (AuSn solder) bond X-rays used to screen the parts were reexamined and revealed no voids between the die and the package (Refere

    11、nce (3). Subsequently, JPL employed an ultrasound inspection technique known as C-mode Scanning Acoustic Microscopy (CSAM). Unlike X-rays, which depict the integrated density of material between the X-ray source and detector, CSAM technology can examine a specific layer. This distinction is particul

    12、arly important when looking for disbonding defects such as non-wetting of surfaces or delamination. Figure 1 is an X-ray of a spare MRO hybrid die; it shows 3 void areas on the left side of the chip, as well as an unfilled via, but does not show areas of poor die attach. In the corresponding CSAM im

    13、age (Figure 2), the 3 large void areas are clearly visible, as well as some smaller ones. The CSAM ultrasound image provides enough detail that, after conversion to a digital image (Figure 3), a more quantitative assessment can be performed that states the total area of disbonds and voids as a perce

    14、ntage of the total die area. Figure 1 is a grayscale image of a rectangular die attach. Thirteen filled vias scattered across the die appear as small black circles, and a single unfilled via appears as a white circle. Between the faintly visible traces are three shadowy ovals that are apparently voi

    15、ds.Figure 1. Microfocus X-ray of hybrid amplifier die (S/N D209) with lid Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Figure 2 is a grayscale image that is clearly the same rectangular die attach. This CSAM image is somewhat grainier, but it show

    16、s the voids in great detail and high contrast, and apparent textures are visible in portions of the image that may represent material characteristics of the layer. Now you can tell that there are three large voids with an area of perhaps 3 percent of the total area of the die, plus a few additional

    17、very small voids.Figure 2. CSAM image of hybrid amplifier die (S/N D209) with lid Figure 3 is also a grayscale image of a different but similar die, except a center rectangle within the grayscale appears as a binary image- each pixel is either completely black or it is white- of that portion of the

    18、die. Two small white rectangles have been overlaid on the image to draw attention to areas of interest, and one of the rectangles surrounds a small white dot (that fills about one-tenth of the rectangle).Figure 3. Binary image converted from a CSAM image of hybrid amplifier die (S/N D221). The white

    19、 boxes identify the most critical (i.e., the FET active) regions The MRO failure investigation suggests that to assure adequate NDE of critical flight hardware, die attach X-rays may need to be supplemented with acoustic images. X-ray imagery can determine that the proper amount of AuSn solder is pr

    20、esent between the die and the carrier, but it cannot determine whether the solder has actually wetted the surfaces. Where there is a complete lack of solder, (i.e., a void) the two imaging methods should give similar results. References: (1) “Transponder DC input current and power increased for 3 ho

    21、urs on DOY 14,“ Jet Propulsion Laboratory Incident Surprise Anomaly No. Z88615, May 31, 2006. (2) “SDST - 3 Hour Power Surge,“ Jet Propulsion Laboratory Problem/Failure Report No. Z88763, June 30, 2006. (3) MRO Small Deep Space Transponder Ka-Band Exciter Anomaly Final Report, Jet Propulsion Laborat

    22、ory Document No. JPL D-31195, March 16, 2007.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Lesson(s) Learned: For critical flight hardware, the current X-ray process for screening RF hybrids may not be adequate to determine the quality of coverage

    23、of the eutectic die attach. CSAM is a non-destructive internal inspection technique that can complement high resolution X-rays by isolating variations in material properties. CSAM detects the extent of air space-type physical defects in components, including cracks, voids, delaminations, and porosit

    24、y, that occur during manufacturing, environmental test, and operation.Recommendation(s): When screening RF hybrids and other complex RF parts, consider the use of CSAM to augment high resolution X-ray inspection.Evidence of Recurrence Control Effectiveness: JPL has referenced this lesson learned as

    25、additional rationale and guidance supporting Paragraph 4.5.3.1 (“Telecommunications System Design: Telemetry Links Spacecraft Downlink RF Carrier“) and Paragraph 4.12.2.1 (“Flight Electronics Hardware System Design: Electronic Packaging Qualification of Electronic Packaging Designs“) in the JPL stan

    26、dard “Design, Verification/Validation and Operations Principles for Flight Systems (Design Principles),“ JPL Document D-17868, Rev. 3, December 11, 2006. This lesson also supports Paragraph 7.5.4 (“Safety and Mission Assurance Practices: Electronic Parts Reliability, Application, and Acquisition“) i

    27、n the Jet Propulsion Laboratory standard “Flight Project Practices, Rev. 6,“ JPL DocID 58032, March 6, 2006.Documents Related to Lesson: Click here to download document. Mission Directorate(s): a71 Space Operationsa71 Sciencea71 Exploration SystemsAdditional Key Phrase(s): a71 Program Management.Ris

    28、k managementProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-a71 Systems Engineering and Analysis.a71 Systems Engineering and Analysis.Planning of requirements verification processesa71 Engineering Design (Phase C/D).a71 Engineering Design (Phase C/D)

    29、.Spacecraft and Spacecraft Instrumentsa71 Manufacturing and Assemblya71 Safety and Mission Assurance.Early requirements and standards definitiona71 Safety and Mission Assurance.Product Assurancea71 Safety and Mission Assurance.Qualitya71 Safety and Mission Assurance.Reliabilitya71 Additional Categor

    30、ies.Communication Systemsa71 Additional Categories.Flight Equipmenta71 Additional Categories.Flight Operationsa71 Additional Categories.Hardwarea71 Additional Categories.Industrial Operationsa71 Additional Categories.Parts, Materials, & Processesa71 Additional Categories.Payloadsa71 Additional Categ

    31、ories.Risk Management/Assessmenta71 Additional Categories.Safety & Mission Assurancea71 Additional Categories.Spacecrafta71 Additional Categories.Test & VerificationAdditional Info: a71 Project: Mars Reconnaissance OrbiterApproval Info: a71 Approval Date: 2007-10-30a71 Approval Name: ghendersona71 Approval Organization: HQProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-


    注意事项

    本文(REG NASA-LLIS-1803--2007 Lessons Learned CSAM Augments X-Ray Inspection of Die Attach (MRO Ka-Band Anomaly).pdf)为本站会员(inwarn120)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开