NAVY MIL-DTL-29611-1996 VEST SURVIVAL AIRCREWMEN-S (AIRSAVE)《男式飞行救生衣》.pdf

《NAVY MIL-DTL-29611-1996 VEST SURVIVAL AIRCREWMEN-S (AIRSAVE)《男式飞行救生衣》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-DTL-29611-1996 VEST SURVIVAL AIRCREWMEN-S (AIRSAVE)《男式飞行救生衣》.pdf（23页珍藏版）》请在麦多课文档分享上搜索。

1、I I MIL-DTL-296 1 1 26 September 1996 DETAIL SPECIFICATION VEST, SURVIVAL, AIRCREWMENS, (AIRSAVE) This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers the general requirements and inspections for the AIRSAV

2、E (Aircrew Integrated Recovey Survival, Armor, Vest and Equipment), survival vest designed to integrate with soft and hard body armor, chemical protective systems, oxygen systems, flotation systems, and survival equipment 1.2 Classification. The vest will come in one size that is adjustable to fit a

3、ll size aircrew, in all conditions, and in the following types and subassemblies: 1.2.1 Types. Type I - With hoisting harness Type II - Without hoisting harness 1.2.2 Subassemblies. General Pocket Knife Pocket Radio Pocket HEED Pocket Pistol Holster Pocket with Ammo Keeper Beneficial comments (recom

4、mendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Commander, Naval Air Warfare Center Aircraft Division, Code 414100 B120-3, Highway 547, Lakehurst, NJ 08733-5100, by using the self-addressed Standardization Document Impro

5、vement Proposal D Form 1426) appearing at the end of this document or by letter. AMSC NIA FSC 8415 DISTRIBUTTON STATEMENT A. Approved for public release; distribution is unlimited. Licensed by Information Handling ServicesMIL-DTL-IIL W 9999906 2022433 324 W # MIL-DTL-296 1 1 2. APPLICABLE DOCUMENTS.

6、 2.1 General. The documents listed in this section are specified in sections 3 and 4 of this specification. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the c

7、ompleteness of this list, document users are cautioned that they must meet all specified requirements documents cited in sections 3 and 4 of this specification, whether or not they are listed. 2.2 Government documents. 2.2.1 SPecifications, standards. and handbooks. The following specifications form

8、 a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DoDISS) and supplement thereto, cited in the solicitation (see 6.2). SPECIFICATIONS FED

9、ERAL A-A-50041 - Snap Link, Mountain Piton, Locking and Non-locking A-A-55620 - Loops, Slide (For Equipage) V-F- 1 06 - Fastener, Slide, Interlocking V-T-295 - Thread, Nylon DEPARTMENT OF DEFENSE MIL-C-3953 MIL- W-408 8 MIL-C-5040 MIL- W-5 664 MIL-C-8061 MIL-K-8662 MIL-F-2 1 840 MIL-B-29604 MIL-B-29

10、605 MIL-W-43668 MIL-W-43 685 MIL-C-43842 Cloth, Duck, Nylon Webbing, Textile, Woven Nylon Cord, Fibrous, Nylon Webbing, Textile, Elastic Cloth, Nylon, Rasche1 Knit Knife, Hunting, Sheathed, Survival, Pilots (Validated) Fastener Tapes, Hook and Pile, Synthetic Body Armor, Soft, Small Arms Protective,

11、 PRU-60AP22P-15 Body Armor, Hard, Small Arms Protective, PRU-6 1A/P22P- 15 Webbing, Textile, Textured or Multifilament Nylon Webbing and Tape, Textile, Aramid Fiber Cloth, Oxford, Aramid 2 Licensed by Information Handling ServicesMIL-DTL-29bLL 999990b 2022432 2b0 MIL-DTL-296 1 1 STANDARDS FEDERAL FE

12、D-STD- 19 1 Textile Text Methods MILITARY MS22019 - Adapter, Parachute Harness, Reversible Quick-Fit MS27980 - MS27983 - Fastener, Snap, Style 4 MS51925 - Ring, Dee - Medium MS70101 - Adapter, Reversible, Quick Fit, 500 Ib, 1-3/4 Inch Fasteners, Snap, Style 2 (Regular Wire Spring Clamp Type) (Unless

13、 otherwise indicated, copies of the above specifications are available fi-om the Standardization Document Order Desk, Building 4D, 700 Robbins Avenue, Philadelphia, PA 191 11-5094.) 2.2.2 Other Government documents, drawings. and mblications. The following other Government documents, drawings, and p

14、ublications form a part of this document to the extent specified herein. Unless otherwise specified, the issues are those cited in the solicitation. NAVAL AIR SYSTEMS COMMAND DRAWINGS 356 IAS 101 356 1 AS301 3 56 1 AS302 3 56 1 AS3 03 3 56 1 AS3 04 3561AS305 3561AS308 3561 AS309 3561AS310 3561AS3 11

15、 3561AS312 Aircrew Integrated Recovery Survival, Armor, Vest, and Equipment (AIRSAVE) Survival Vest Assembly Survival Vest Sub-Assembly Hoisting Harness Assemblies D-Ring Retaining Flap Assembly Identification Label OxygedCBR Attachment Assembly Flashlight Attachment Assembly General Pocket Assembly

16、 Radio Pocket Assembly Knife Pocket Assembly 3 Licensed by Information Handling ServicesMIL-DTL-29bLL m 9999906 2022433 IT7 NAVAL AIR SYSTEMS COMMAND DRAWINGS (Contd) 3561AS313 - PistoVAmmunition Pocket Assembly 3561AS3 14 - HEED Pocket Assembly (Unless otherwise specified, copies of drawings requir

17、ed by contractors in connection with specific acquisition functions should be obtained from the contracting activity, or as directed by the contracting officer.) 2.3 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this do

18、cument shall takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 First article. When specified (see 6.2), a sample shall be subjected to first article inspection in accordance with 4.2. 3.2

19、 Materials and components. The materials and components shall conform to applicable specifications, patterns, and drawings and shall be as specified herein. Equivalent materials and parts require approval by the Naval Air Warfare Center Aircraft Division, Code 4.6.2, Patuxent River, Maryland 20670-5

20、304. Requests for use of equivalent items shall be submitted to the Contracting Officer. Recycled materials may be used (see 6.6). 3.2.1 Vest components. The vest components shall be constructed with the materials specified in 3.2.1.1 through 3.2.1.14. 3.2.1.1 Base fabric. The base fabric for the ve

21、st and the inside pockets shail be raschel knit nylon mesh conforming to MIL-C-8061, Color 106 Olive Green. The mesh shail be fire resistant (FR) treated with a chemical coating and shall be tested in accordance with 4.5. 3.2.1.2 Modular Pockets. The vest shall come with the following modular pocket

22、s: knife, radio, and general pockets, and when requested to the HEED pocket and pistol holster pocket with ammo keeper, and attached inside pockets. The modular pockets shall form the subassemblies of the vest. The pockets and the inside pocket flaps shall be fabricated from aramid oxford cloth conf

23、orming to MIL-C-43842, Class I, Color 106 Olive Green. Modular pockets shall be provided unattached to vest. 4 Licensed by Information Handling ServicesMIL-BTL-29611 9799906 2022434 033 D MIL-DTL-296 1 1 3.2.1.2.1 Fit gage set. The fit gage set shall consist of the general, knife, and radio, and if

24、requested, HEED and pistol gages. The set shall be used to veri pocket fabrication and dimensions. The set shall be manufactured fiom any hard wood material (see 4.4.3). Gages shall have a tolerance of fl/8 inch. The following shall be used as gages. Knife - Gage in accordance with figure 1 Pistol -

25、 Gage in accordance with figure 2 Clip - Block of dimensions: 3 x 1 1/2 x 1 inches Radio - Block of dimensions: 7 x 1 1/2 x 4 inches HEED - Cylinder with the following dimensions: Diameter 2 inches, Height 10 inches General - Block of dimensions: 2 3/4 x 1 1/2 x 4 inches 3.2.1.3 Stiffener. The stiff

26、ener used to give rigidity and strength to the radio, HEED, and pistol pockets shall conform to MIL-C-3953, Color 106 Olive Green. 3.2.1.4 Webbing. The webbing used for modular survival item pocket attachment to the vest and LPU strap fabrication shall conform to MIL-W-43668, Type III, 1 inch wide,

27、Color 106 Olive Green. The webbing shall be fire resistant (FR) treated with a chemical coating and shall be tested in accordance with 4.5. 3.2.1.5 Elastic webbing. The elastic webbing used for the fabrication of the HEED pocket, ammo pocket and hoisting keepers shall conform to MIL-W-5664, Type I,

28、Class I, 1 inch wide, Color 106 Olive Green. 3.2.1.6 Webbing, aramid binding. The woven binding tape used for fabrication of the vest shall be 1 inch wide conforming to MIL-W-43685, Type II, Color 106 Olive Green. 3.2.1.7 Fastener tapes. The hook and pile fastener tapes used to fabricate the vest sh

29、all conform to MIL-F-2 1 840, Type II, Class I, Color 106 Olive Green. 3.2.1.8 Slide fastener. The slide fastener used to fabricate the survival vest shall be heavy weight with plastic teeth and a metal slide conforming to V-F-106, Type IV, Style 15. 3.2.1.9 Loop-locs. The loop-locs used for connect

30、ing the body armor to the vest shall be to part number 01004-20-21883 of ITW Waterbury, 952 S. Main Street, Waterbury, CT 06721, Cage No. 82399 or equal. 3.2.1.10 Snap fasteners. Omnidirectional snap fasteners used to fabricate the vest and pockets shall conform to MS27980, Style 2, and unidirection

31、al snap fasteners shall conform to MS27983, Style 4. 5 Licensed by Information Handling Services 2022435 I J c - MIL-DTL-296 1 1 a f Note: 1. All dimensions in inches. FIGURE 1. Knife gage dimensions. 6 Licensed by Information Handling ServicesMIL - D a I- - 2 9 b II L r- * I 399990b 20224Lb 906 MIL

32、-DTL-296 1 1 ci 1. All dimensions in inches. FIGURE 2. Gun gage dimensions. 7 Licensed by Information Handling ServicesMIL-DTL-296 1 1 3.2.1.1 1 LPU-2Vand 23P collar lobe attachment D-rings. n The D-rings use to fabricate the collar lobe attachment shall be in accordance with MS5 1925. 3.2.1.12 LPU-

33、2lIand 23/P collar lobe attachment slide loops. The slide loops used to fabricate the collar lobe attachment shall be in accordance with A-A-55620. 3.2.1.13 Knife sheath. The knife sheath shall conform to MIL-K-8662, except that it shall not contain the sharpening stone, sharpening stone pocket, nyl

34、on laces, lace holes, and slots for insertion of belt. 3.2.1.14 Thread. The nylon thread used to fabricate the hoisting harness shall be in accordance with V-T-295, Class I, Type I, Size 6. All other thread shall be V-T-295.Type II, Class A, Size E. 3.2.1.15 Attachments. 3.2.1.15.1 OxygedCBR attachm

35、ent. The oxygen/CBR attachment shall be in accordance with applicable drawings. The webbing used for fabrication of this attachment shall conform to MIL-W-43668, Type III, 1 inch wide. 3.2.1.15.2 Flashlight attachment. The flashlight attachment shall be in accordance with applicable drawings. The we

36、bbings used for fabrication of this attachment shall conform to MIL-W-43668, Type III, 1 inch wide and MIL-W-5664, Type I, Class 1, 1 inch wide. 3.2.2 Hoisting harness. The integral hoisting harness shall be constructed with the materials specified in 3.2.1.14 and 3.2.2.1 through 3.2.2.4. 3.2.2.1 Ha

37、rness webbing. The webbing used to fabricate the hoisting harness assembly shall be 1 23/32 inch wide nylon conforming to MIL-W-4088, Type XIII, Color 106 Olive Green. 3.2.2.2 Snaplink. The snaplink used for hoisting shall be D-shaped, non-locking, conforming to A-A-50041, Type III. 3.2.2.3 Friction

38、 adapters. The friction adapters used to fabricate the hoisting harness shall conform to MS70101 for the chest adapter and MS22019 for the leg adapters. 3.2.2.4 Harness retainer cord and pocket tether loops. The harness retainer cord used to fabricate the hoisting harness assembly and pocket tether

39、loops shall conform to MIL-C-5040, Type IIA, Nylon Cord, Coreless, Color 106, Olive Green. 8 Licensed by Information Handling ServicesMIL-DTL-296 1 1 3.3 Design and construction. The mesh vest shall have four sewn-in inside pockets and various modular removable pockets. The modular pockets shall be

40、unattached when delivered. The vest shall be adjustable under each arm and in the back by reeving together overlapping vest panels. The vest shall integrate with the soft body armor in accordance with MIL-B-29605 and hard body armor in accordance with MIL-B-29604. Drill holes are prohibited. The des

41、ign and construction of the vests shall conform to the patterns, figures 3 and 4, and the drawings listed herein: 3 56 1AS 1 O 1 356 1 AS3 1 O 3561 AS301 3 56 1AS305 3561AS311 3 56 1 AS3 02 3561AS308 3561AS3 12 3 56 1 AS303 3 561AS309 3561 AS3 13 3 56 1 AS3 04 3561AS3 14 3.3.1 Cut edges. The cut edg

42、es of the nylon webbings, cords, and tapes, except for the hook and loop fastener tapes, shall be seared, prior to the fabrication of the vests and pockets, to prevent fraying. No sharp edges shall be formed. The cut edges of the aramid cloth, shall be overedged stitched (serged) except those that a

43、re completely covered by aramid binding tape, hook and loop fastener tapes, or are completely encased by the seam construction. 3.3.1.1 Patterns. Standard patterns shall be furnished to the contractor for use in cutting working patterns (see 6.4). The working patterns shall be identical to the gover

44、nment patterns. Minor modifications are permitted where necessary when using automatic equipment, provided these modifications shall not alter the dimensional serviceability or appearance requirements cited in the solicitation. The modular pockets have a 3/8 inch seam allowance, except where binding

45、 is required. 3.3.1.2 List of pattern parts and applicable materials. 3.3.1.2.1 Cloth. nvlon. raschel knit. (MIL -C-8064 with FR coating. Color 106 Olive Green). Nomenclature - cut Pattern No. Vest, Front 2 3561AS380-1, Right / 3561AS380-2, Left Vest, Back 2 3561AS380-3, Right l3561AS380-4, Lefi Ins

46、ide Upper Pocket 2 3561AS380-7, Left / 3561AS380-8, Right Inside Lower Pocket 2 3561AS380-9, Lefi / 3561AS380-10, Right 9 Licensed by Information Handling Services MIL-DTL-Zb11 m 999990b 2022419 bL5 m MIL-DTL-296 1 1 1. Radio Pocket 6. Snap-Link .2. General Pocket 7. Snap-Link Cover 3. HEED Pocket 8

47、. Knife Pocket 4. Pistol Holster Pocket 9. Loop-LOCS with Aiiiiiio Keeper 10. Slide Fastener 5. Collar Lobe Attachment 11. Fllisliliglit Attachmeiit FIGURE 3. AIRSAVE vest (outside view). 10 Licensed by Information Handling ServicesMIL-DTL-296 1 1 U (5 U 1. 2. 3. 4. 5. 6. 7. 8. Slide Fasteiier 9. Ha

48、rness Retainer Cord Inside Pockets (Water Bags) Chest Strap Riglit Leg Strap Left Leg Strap Lift Strap Leg Striip Retainer Hariiess Keeper 10. Friction Adapter (Chest) 11. Friction Adapters (Legs) 12. hiside Pockets (General Kit, Medical 13. Siiap Link Kit) FIGURE 4. AIRSAVE vest (inside view) with

49、hoisting Iiariiess. 11 Licensed by Information Handling ServicesMIL-DTL-296 1 1 4 3.3.1.2.2 Cloth. aramid oxford (Mn, -C-43 842. Class I. Color 106 Olive Green). Nomenclature - cut Pattern No. Upper and Lower Pocket Flap D-Ring Retaining Flap General Pocket Radio Pocket Knife Pocket Pistol Holster Panel Magazine Pouch Panel HEED Pocket Front HEED Pocket Back 3561AS380-5, Left / 3561AS380-6, Right 3561AS380-11 3 56 1AS390- 1 3561AS39 1-1 3561AS392- 1 356 1 AS393- 1 3 56 1 AS3 93-2 3 56 1 AS394-1 3 56 1 AS394-2 3.3.1.2.3 Cloth, Duck. Nylon (ME-C-3953, Color 106 Olive Green). Nom