GME 00005-2012 General Requirements for Vacuum Metallised Plastic Components (Revision 2 English German Includes Appendix This standard may be applied only for current projects It l.pdf

《GME 00005-2012 General Requirements for Vacuum Metallised Plastic Components (Revision 2 English German Includes Appendix This standard may be applied only for current projects It l.pdf》由会员分享，可在线阅读，更多相关《GME 00005-2012 General Requirements for Vacuum Metallised Plastic Components (Revision 2 English German Includes Appendix This standard may be applied only for current projects It l.pdf（15页珍藏版）》请在麦多课文档分享上搜索。

1、GeneralSpecification SUPERCEDEDGME 00005General Requirements for VacuumMetallised Plastic ComponentsAllgemeine Anforderungenan Kunststoffteile mit Metall-bedampfungNote: This standard may be applied only forcurrent projects. It is Superceded for all futureprojects and replaced by GMW16650.HINWEIS: D

2、iese Spezifikation darf nur noch frlaufende Projekte angewendet werden und istfr alle zuknftigen Projekte ungltig und ersetztdurch GMW16650.1 Release and Revisions 1 Freigabe und nderungen1.1 Release. The standard was first approved andreleased in JUN 1979.1.1 Freigabe. Diese Vorschrift wurde erstma

3、liggenehmigt und freigegeben im JUN 1979.1.2 Revisions. 1.2 nderungen.Rev. Date /DatumDescription (Org.) /Beschreibung (Org.)2 NOV 2012 Superceded (GME Cross Carline Specifications) /Superceded (GME Cross Carline Specifications) Copyright 2012 General Motors Company All Rights ReservedPublication De

4、partment: GME Specification CenterNovember 2012 - Issue No. 2 Page 1 of 1PRD045 - VPRE ST 1 10/03 TEST SPECIFICATION PRiiFVORSCHRlFT General Requirement8 for Vacuum Metalliaed Plastic GME Components 00 005 Allgemeine Anforderungen an Kunststoffteile mit Metallbedampfung Revisionslkderungen Date/Datu

5、m Sym/Pos DescriptionBeschreibung Appd/Gen ApprovedlGenehmigt a*hh Vauxhall Motors LTD Adam Opel AG Engineering Materials Laboratory PEK-Werkstoffentwicklung Despite spot checks possibly performed by the receiver, it is the suppliers responsibility that the delivered parts are in line with these spe

6、cifications. Deliveries of samples, first off-tool parts and parts, the performance of which has been changed, must be accompanied by a test report showing the test results in terms of figures. Unbeschadet etwaiger durch den Abnehmer erfolgenden Stichprobenprtifungen tragt der Lieferant die Verant w

7、ortung dafur, daR die gelieferte Ware diese Vorschriften erfiillt. Ein Prtifbericht mit zahlenml Belichtungs- aussehen dauer (1000 - 3)h; 18h:lOZ min belichten, lamin belichten und spriihen, dann 6h dunkel. (PrDfprogramm Cam No. 47) Schwarftafel-Temperetur bei Eelichtung +71C - 3K. * Nur Ausfijhrung

8、 Al und A2 Issue 1 Date of Issue Prepared Page of Ausgabe Ausgabedatum 6179 Ausgefertlgt Serte 7 van 13 I 6.2.6 Resistance to Temperature Cycling Test pieces shall show no Test pieces shall be subjected to the significant surface following test cycle: changes e.g. tadkinees, blisters, loosening of 6

9、.2.6.1 (17 i: 0,5)h at -3OC f 3K followed by metallic film, change in colour or gloss or other 6.2.6.2 (72 t 1)h at +80C 2 2,5K then changes detrimental to appearance and servicea- 6.2.6.3 (24 2 1)h at +40C !: 2K and (93 z 21% bility. Test pieces shall relative humidity then comply with the dimeneio

10、r specified on the drawing 6.2.6.4 (7 2 0,5)h at -3OC i 3H end finally after completion of the test. 6.2.6.5 (24 2 1)h at +40C 2 2K and (93 2 2% relative humidity 6.2.6.6 Number of cycles: 6.2.6.6.1Type Al and AZ: Two cycles 6.2.6.6.2Type El and 82: One cycle The test cycle may be commenced at any o

11、f the individual stages provided the full cycle is sequentially completed. This cycle shall be carried out without interruption. 6.2.7 Colour Fastness to Daylight to GME 60 372 - Except total exposure as shown. 6.2.7.1 TypeAl and A2 - 51000 Langleys direct No significant changes 6.2.7.2 Type f3? and

12、 82 - 25500 Langleys under glass in surface appearance. Note: This test shall only be used in cases of dispute concerning test to clauses 6.2.2 or 6.2.5 6.2.8 Salt Spray Fog Testing to GME 60 206 - 6.2.8.1 Type Al and A2:Code H- Grade 1 6.2.8.2 Type Eland 82:Code E- Grade 1 6.2.9 Finish Adhesion to

13、GME 60 343 - C - (or to GME 60 343 - B-where sample size dictates) Except grid lines shall be 1,5mm apart. Test shall be conducted; continued page ID Issue Date of Issue 1 6/79 Page of Ausqabe Ausgabedatum Selte a VOll 13 6.2.6 Zyklus - Priifung Die Teile werden nachfolgonden Temperatur- Heine Veran

14、darung der Ober. und Hlimebedingungen ausgesetzt: fltiche, der Farbe, des Glanzes; keine Blasen, kein 6.2.6.1 (17 2 0,5)h bei -3OC 2 3H anschlieflend Hlebrigwerden. Hein L6sen der Metellbedampfung oder 6.2.6.2 (72 +, 1)h bei +80C f 2,5H danach sonstige Vertinderungen, dir die Gebrauchsfahigkeit be-

15、6.2.6.3 (24 +, 1)h bei +40C !: 2H und (93 f 21% eintrachtigen. Das Teil muf relative Luftfeuchte, anschlieaend nach der PrDfung hin- sichtlich seiner Abmessun- 6.2.6.4 (7 f 0,5)h bei -3OC 2 3K und danach gen innerhalb der Zeich- nungstoleranzen liegen. 6.2.6.5 (24 r 1)h bei +40C 2 2H und (93 ? 2)% r

16、elative Luftfeuchte 6,2,6,6 Anzahl der Zyklen: 6.2.6.6.7 Ausfijhrung Al und A2:Zwei Zyklen 6.2.6.6.2 Ausfiihrung Bl und El2:Ein Zyklus Unter Seibehaltung der angegebenen Reihenfolge kann der Zyklus beliebig begonnen werden. Der Zyklus muQ ohne Unterbrechung durchge- fijhrt werden. 6.2.7 Tageslichtbe

17、standigkeit nach GME 60 372 - jedoch nach folgenden Gelichtungszeiten 6.2.7.1 Ausfiihrung Al und A2:51 000 Langleys direk t. I Heine sichtbaren Ober- fllo$ed by (76 - I) hours recovery at +23 C - 5H (Type Al and A2only). 6.2.9.5 Aftef tests to clause 6.2.6 foiloyed by (16 - I) hours recovery at +23

18、C - 5H 6.2.9.6 After tests to clause 6.2.8 follgweq by - at least 1 hour recovery at +23 C - 5H 6.2.10 Resistance to Cleaning Agents Rating 1 to GHE 60 266-(Type 1 only) 6.2.11 Resistance to Sulphur Dioxide Staining to GME 60 263 - see requirements to clause 7, GME 60 263 6.2.12 Resistance to Sulphi

19、de Staining to GME 60 264 - see requirements to clause 7, GHE 60 264 6.2.13 Resistance to Synthetic Perspiration to requirements clause 6 Solution to GME 60 275-(Type 1 only) of GME 60 275 6.2.14 Abrasion Resistance 6.2.14.1 Type A?: GME 60 269 - X - B 6.2.14.2 TypeS.?: GMt60 269 - Y - A 7. Addition

20、al Requirements Other additional requirements may be specified on the relevant engineeri drawings, material specifications etc. 8. Codinq This specification shall be called up on drawings, sub assembly drawing5 material specifications etc. as “GME 00 005 Type Al“ “GME 00 005 Type Al optional Type A2“ “GE 00 005 TypeA2* “GME 00 005 TypeSI:“ “GME 00 005 Type81 optional Type 82“ “GME 00 005 Type 82“ Issue Date of Issue 1 Ausgefertlgt :z nach QU t%XH - Cadmium Issue Ausgabe 1 Oate of Issue Ausgabedatum Page , Of , sette von