ISO 8843 AMD 1-2012 Aircraft - Crimp-removable contacts for electrical connectors - Identification system Amendment 1《航空器 电气连接器用可移除卷边触点 识别系统 修改件1》.pdf

《ISO 8843 AMD 1-2012 Aircraft - Crimp-removable contacts for electrical connectors - Identification system Amendment 1《航空器 电气连接器用可移除卷边触点 识别系统 修改件1》.pdf》由会员分享，可在线阅读，更多相关《ISO 8843 AMD 1-2012 Aircraft - Crimp-removable contacts for electrical connectors - Identification system Amendment 1《航空器 电气连接器用可移除卷边触点 识别系统 修改件1》.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、ISO TC 20/SC 1 ISO 8843:2005/Amd.1:2012(E) Secretariat: SAC/CARIS 2 edition 2012-09-01 Aircraft Crimp-removable contacts for electrical connectors - Identification system Amendment 1 Aronefs Contacts sertir amovibles pour connecteurs lectriques - Systme didentification Amendement 1 Aircraft Crimp-re

2、movable contacts for electrical connectors Identification system Amendment 1 Aronefs Contacts sertir amovibles pour connecteurs lectriques Systme didentification Amendement 1 ISO 8843:2005/Amd.1:2012(E) ii ISO 2012 All rights reservedCopyright notice This ISO document is a Draft International Standa

3、rd and is copyright-protected by ISO. Except as permitted under the applicable laws of the users country, neither this ISO draft nor any extract from it may be reproduced, stored in a retrieval system or transmitted in any form or by any means, electronic, photocopying, recording or otherwise, witho

4、ut prior written permission being secured. Requests for permission to reproduce should be addressed to either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyr

5、ightiso.org Web www.iso.org Reproduction may be subject to royalty payments or a licensing agreement. Violators may be prosecuted. ISO 8843:2005/Amd.1:2012(E) ISO 2012 All rights reserved iii C ontents Page Foreword iii Introduction iv 1 Scope 1 ISO 8843:2005/Amd.1:2012(E) iv ISO 2012 All rights res

6、ervedForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for whic

7、h a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all ma

8、tters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circ

9、ulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held respons

10、ible for identifying any or all such patent rights. Amendment 1 to ISO 8843:2005 was prepared by Technical Committee ISO/TC 20, Aircraft and space vehicles, Subcommittee SC 1, Aerospace electrical requirements. ISO 8843:2005/Amd.1:2012( E) ISO 2012 All rights reserved 1Aircraft Crimp-removable conta

11、cts for electrical connectors - - Identification system Amendment 1 Aircraft Crimp-removable contacts for electrical connectors Identification system Amendment 1 Page 2, Item 3.2 a) Add the following letter code to the existing list: CT: copper/tellurium; or Delete the “or“ after “CN: copper/nickel;“.