ETSI TS 103 191-1-2015 Intelligent Transport Systems (ITS) Testing Conformance test specifications for Signal Phase And Timing (SPAT) and Map (MAP) Part 1 Test requirements and Pro.pdf

《ETSI TS 103 191-1-2015 Intelligent Transport Systems (ITS) Testing Conformance test specifications for Signal Phase And Timing (SPAT) and Map (MAP) Part 1 Test requirements and Pro.pdf》由会员分享，可在线阅读，更多相关《ETSI TS 103 191-1-2015 Intelligent Transport Systems (ITS) Testing Conformance test specifications for Signal Phase And Timing (SPAT) and Map (MAP) Part 1 Test requirements and Pro.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、 ETSI TS 103 191-1 V1.1.1 (2015-09) Intelligent Transport Systems (ITS); Testing; Conformance test specifications for Signal Phase And Timing (SPAT) and Map (MAP); Part 1: Test requirements and Protocol Implementation Conformance Statement (PICS) pro forma TECHNICAL SPECIFICATION ETSI ETSI TS 103 19

2、1-1 V1.1.1 (2015-09)2 Reference DTS/ITS-00139 Keywords ITS, PICS, testing ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06)

3、N 7803/88 Important notice The present document can be downloaded from: http:/www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the

4、 prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the pres

5、ent document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http:/portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of

6、the following services: https:/portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of

7、the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2015. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo are Trade Marks of

8、 ETSI registered for the benefit of its Members. 3GPPTM and LTE are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM and the GSM logo are Trade Marks registered and owned by the GSM Association. ETSI ETSI TS 103 191-1 V1.1.1 (2015-09)3 Conten

9、ts Intellectual Property Rights 4g3Foreword . 4g3Modal verbs terminology 4g31 Scope 5g32 References 5g32.1 Normative references . 5g32.2 Informative references 5g33 Definitions and abbreviations . 6g33.1 Definitions 6g33.2 Abbreviations . 6g34 Conformance requirement concerning PICS 6g3Annex A (norm

10、ative): MAP-SPAT PICS pro forma 7g3A.1 Partial cancellation of copyright . 7g3A.2 Guidance for completing the ICS pro forma 7g3A.2.1 Purposes and structure 7g3A.2.2 Abbreviations and conventions 7g3A.2.3 Instructions for completing the ICS pro forma . 9g3A.3 Identification of the implementation 9g3A

11、.3.1 Introduction 9g3A.3.2 Date of the statement 9g3A.3.3 Implementation Under Test (IUT) identification . 9g3A.3.4 System Under Test (SUT) identification 9g3A.3.5 Product supplier 10g3A.3.6 Client (if different from product supplier) 10g3A.3.7 ICS contact person 11g3A.4 Identification of the protoc

12、ol 11g3A.5 Global statement of conformance . 11g3A.6 Tables . 11g3A.6.1 Introduction 11g3A.6.2 Station type . 11g3A.6.3 RSU EU profile 12g3Annex B (informative): Bibliography . 13g3History 14g3ETSI ETSI TS 103 191-1 V1.1.1 (2015-09)4 Intellectual Property Rights IPRs essential or potentially essenti

13、al to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified

14、 to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http:/ipr.etsi.org). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the

15、 existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Technical Specification (TS) has been produced by ETSI Technical Committee Intelligent Transport Systems (ITS). The

16、 present document is part 1 of a multi-part deliverable covering Conformance test specification for Signal Phase And Timing (SPAT) and Map (MAP), as identified below: Part 1: “Test requirements and Protocol Implementation Conformance Statement (PICS) pro forma“; Part 2: “Test Suite Structure and Tes

17、t Purposes (TSS Part 3: “Abstract Test Suite (ATS) and Protocol Implementation eXtra Information for Testing (PIXIT)“. The development of ITS test specifications follows the guidance provided in the ETSI EG 202 798 i.1. Therefore, the ATS documentation outlined in the present document is also based

18、on the guidance provided in ETSI EG 202 798 i.1. Modal verbs terminology In the present document “shall“, “shall not“, “should“, “should not“, “may“, “need not“, “will“, “will not“, “can“ and “cannot“ are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the e

19、xpression of provisions). “must“ and “must not“ are NOT allowed in ETSI deliverables except when used in direct citation. ETSI ETSI TS 103 191-1 V1.1.1 (2015-09)5 1 Scope The present document provides the Protocol Implementation Conformance Statement (PICS) pro forma for Conformance test specificati

20、on for MAP-SPAT Messages (MAP-SPAT) as defined in SAE J2735 1 in compliance with the relevant requirements and in accordance with the relevant guidance given in ISO/IEC 9646-7 4. The objective of the present document is to provide a basis for conformance tests for MAP-SPAT Messages (MAP-SPAT) equipm

21、ent giving a high probability of interoperability between different manufacturers equipment. The ISO standard for the methodology of conformance testing (ISO/IEC 9646-1 2 and ISO/IEC 9646-2 3) as well as the ETSI rules for conformance testing (ETSI ETS 300 406 5) are used as a basis for the test met

22、hodology. 2 References 2.1 Normative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the reference docume

23、nt (including any amendments) applies. Referenced documents which are not found to be publicly available in the expected location might be found at http:/docbox.etsi.org/Reference. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their l

24、ong term validity. The following referenced documents are necessary for the application of the present document. 1 SAE J2735 (2015-04-30): “Dedicated Short Range Communications (DSRC) Message Set Dictionary“. 2 ISO/IEC 9646-1 (1994): “Information technology - Open Systems Interconnection - Conforman

25、ce testing methodology and framework - Part 1: General concepts“. 3 ISO/IEC 9646-2 (1994): “Information technology - Open Systems Interconnection - Conformance testing methodology and framework - Part 2: Abstract Test Suite specification“. 4 ISO/IEC 9646-7 (1995): “Information technology - Open Syst

26、ems Interconnection - Conformance testing methodology and framework - Part 7: Implementation Conformance Statements“. 5 ETSI ETS 300 406 (1995): “Methods for testing and Specification (MTS); Protocol and profile conformance testing specifications; Standardization methodology“. 6 ETSI TS 102 894-2 (V

27、1.2.1): “Intelligent Transport Systems (ITS); Users and applications requirements; Part 2: Applications and facilities layer common data dictionary“. 2.2 Informative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific.

28、 For specific references, only the cited version applies. For non-specific references, the latest version of the reference document (including any amendments) applies. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term vali

29、dity. The following referenced documents are not necessary for the application of the present document but they assist the user with regard to a particular subject area. i.1 ETSI EG 202 798 (V1.1.1): “Intelligent Transport Systems (ITS); Testing; Framework for conformance and interoperability testin

30、g“. ETSI ETSI TS 103 191-1 V1.1.1 (2015-09)6 3 Definitions and abbreviations 3.1 Definitions For the purposes of the present document, the terms and definitions given in SAE J2735 1, ISO/IEC 9646-1 2 and ISO/IEC 9646-7 4 apply. 3.2 Abbreviations For the purposes of the present document, the followin

31、g abbreviations apply: ATS Abstract Test Suite DSRC Dedicated Short Range Communications EU European Union ICS Implementation Conformance Statement ISO International Organization for Standardization ITS Intelligent Transport Systems IUT Implementation Under Test MAP MapData Messages PDU Protocol Dat

32、a Unit PICS Protocol Implementation Conformance Statement RSU Road Side Unit SAE Society of Automotive Engineers SPAT Signal Phase And Timing Messages SUT System Under Test TP Test Purpose TS Technical Specification TSS Test Suite Structure 4 Conformance requirement concerning PICS If it claims to c

33、onform to the present document, the actual PICS pro forma to be filled in by a supplier shall be technically equivalent to the text of the PICS pro forma given in annex A, and shall preserve the numbering, naming and ordering of the pro forma items. An ICS which conforms to the present document shal

34、l be a conforming PICS pro forma completed in accordance with the instructions for completion given in clause A.2. ETSI ETSI TS 103 191-1 V1.1.1 (2015-09)7 Annex A (normative): MAP-SPAT PICS pro forma A.1 Partial cancellation of copyright Notwithstanding the provisions of the copyright clause relate

35、d to the text of the present document, ETSI grants that users of the present document may freely reproduce the MAP-SPAT PICS pro forma in this annex so that it can be used for its intended purposes and may further publish the completed MAP-SPAT PICS. A.2 Guidance for completing the ICS pro forma A.2

36、.1 Purposes and structure The purpose of this PICS pro forma is to provide a mechanism whereby a supplier of an implementation of the requirements defined in SAE J2735 1 may provide information about the implementation in a standardized manner. The PICS pro forma is subdivided into clauses for the f

37、ollowing categories of information: guidance for completing the ICS pro forma; identification of the implementation; identification of the SAE J2735 1; global statement of conformance; PICS pro forma tables. A.2.2 Abbreviations and conventions The ICS pro forma contained in this annex is comprised o

38、f information in tabular form in accordance with the guidelines presented in ISO/IEC 9646-7 4. The item column contains a number which identifies the item in the table. Item description column The item description column describes in free text each respective item (e.g. parameters, timers, etc.). It

39、 implicitly means “is supported by the implementation?“. Status column The following notations, defined in ISO/IEC 9646-7 4, are used for the status column: m mandatory - the capability is required to be supported. o optional - the capability may be supported or not. n/a not applicable - in the give

40、n context, it is impossible to use the capability. x prohibited (excluded) - there is a requirement not to use this capability in the given context. o.i qualified optional - for mutually exclusive or selectable options from a set. “i“ is an integer which identifies an unique group of related optiona

41、l items and the logic of their selection which is defined immediately following the table. c.i conditional - the requirement on the capability (“m“, “o“, “x“ or “n/a“) depends on the support of other optional or conditional items. “i“ is an integer identifying an unique conditional status expression

42、 which is defined immediately following the table. ETSI ETSI TS 103 191-1 V1.1.1 (2015-09)8 i irrelevant (out-of-scope) - capability outside the scope of the reference specification. No answer is requested from the supplier. NOTE 1: This use of “i“ status is not to be confused with the suffix “i“ to

43、 the “o“ and “c“ statuses above. Reference column The reference column makes reference to SAE J2735 1, except where explicitly stated otherwise. Support column The support column shall be filled in by the supplier of the implementation. The following common notations, defined in ISO/IEC 9646-7 4, ar

44、e used for the support column: Y or y supported by the implementation. N or n not supported by the implementation. N/A, n/a or - no answer required (allowed only if the status is n/a, directly or after evaluation of a conditional status). NOTE 2: As stated in ISO/IEC 9646-7 4, support for a received

45、 PDU requires the ability to parse all valid parameters of that PDU. Supporting a PDU while having no ability to parse a valid parameter is non-conformant. Support for a parameter on a PDU means that the semantics of that parameter are supported. Values allowed column The values allowed column conta

46、ins the type, the list, the range, or the length of values allowed. The following notations are used: range of values: EXAMPLE 1: 5 20 list of values: , , ., EXAMPLE 2: 2 ,4 ,6 ,8, 9 EXAMPLE 3: 1101B, 1011B, 1111B EXAMPLE 4: 0AH, 34H, 2FH list of named values: (), (), ., () EXAMPLE 5: reject(1), acc

47、ept(2) length: size ( ) EXAMPLE 6: size (1 8) Values supported column The values supported column shall be filled in by the supplier of the implementation. In this column, the values or the ranges of values supported by the implementation shall be indicated. References to items For each possible ite

48、m answer (answer in the support column) within the ICS pro forma a unique reference exists, used, for example, in the conditional expressions. It is defined as the table identifier, followed by a solidus character “/“, followed by the item number in the table. If there is more than one support colum

49、n in a table, the columns are discriminated by letters (a, b, etc.), respectively. EXAMPLE 7: A.5/4 is the reference to the answer of item 4 in table 5 of annex A. EXAMPLE 8: A.6/3b is the reference to the second answer (i.e. in the second support column) of item 3 in table 6 of annex A. ETSI ETSI TS 103 191-1 V1.1.1 (2015-09)9 Prerequisite line A prerequisite line takes the form: Prerequisite: . A prerequisite line after a clause or table title indicates that the whole clause or the whole t