EN ISO 16407-1-2017 en Electronic fee collection - Evaluation of equipment for conformity to ISO 17575-1 - Part 1 Test suite structure and test purposes.pdf

《EN ISO 16407-1-2017 en Electronic fee collection - Evaluation of equipment for conformity to ISO 17575-1 - Part 1 Test suite structure and test purposes.pdf》由会员分享，可在线阅读，更多相关《EN ISO 16407-1-2017 en Electronic fee collection - Evaluation of equipment for conformity to ISO 17575-1 - Part 1 Test suite structure and test purposes.pdf（116页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06Electronic fee collection Evaluation of equipment for conformity to ISO 17575-1Part 1: Test suite structure and test purposes (ISO 16407-1:2017)BS EN ISO 16407-1:2017EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN

2、ISO 16407-1 December 2017 ICS 03.220.20; 35.240.60 Supersedes CEN ISO/TS 16407-1:2011English Version Electronic fee collection - Evaluation of equipment for conformity to ISO 17575-1 - Part 1: Test suite structure and test purposes (ISO 16407-1:2017) Perception du tlpage - valuation de la conformit

3、de lquipement lISO 17575-1 - Partie 1: Structure de la suite dessais et objectifs des essais (ISO 16407-1:2017) Elektronische Gebhrenerhebung - Konformittsbeurteilung von Gerten nach ISO/TS 17575-1 - Teil 1: Struktur und Zweck des Prfprogrammes (ISO 16407-1:2017) This European Standard was approved

4、by CEN on 5 December 2017. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national sta

5、ndards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and

6、notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary

7、, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN

8、-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels 2017 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 16407-1:2017 ENational forewordThis British Standard is the UK implementation of EN ISO 164071:2017. It is i

9、dentical to ISO 164071:2017. It supersedes DD CEN ISO/TS 164071:2011, which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee EPL/278, Intelligent transport systems.A list of organizations represented on this committee can be obtained on request to its secreta

10、ry.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2018 Published by BSI Standards Limited 2018ISBN 978 0 580 96428 2ICS 35.240.60; 03.220.20Compliance with a British Standar

11、d cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 January 2018.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN ISO 164071:2017EUROPEAN STANDARD NORME EUROP

12、ENNE EUROPISCHE NORM EN ISO 16407-1 December 2017 ICS 03.220.20; 35.240.60 Supersedes CEN ISO/TS 16407-1:2011English Version Electronic fee collection - Evaluation of equipment for conformity to ISO 17575-1 - Part 1: Test suite structure and test purposes (ISO 16407-1:2017) Perception du tlpage - va

13、luation de la conformit de lquipement lISO 17575-1 - Partie 1: Structure de la suite dessais et objectifs des essais (ISO 16407-1:2017) Elektronische Gebhrenerhebung - Konformittsbeurteilung von Gerten nach ISO/TS 17575-1 - Teil 1: Struktur und Zweck des Prfprogrammes (ISO 16407-1:2017) This Europea

14、n Standard was approved by CEN on 5 December 2017. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references conc

15、erning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member in

16、to its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France,

17、Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHE

18、S KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels 2017 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 16407-1:2017 EBS EN ISO 164071:2017EN ISO 16407-1:2017 (E) 3 European foreword This

19、document (EN ISO 16407-1:2017) has been prepared by Technical Committee ISO/TC 204 “Intelligent transport systems” in collaboration with Technical Committee CEN/TC 278 “Intelligent transport systems” the secretariat of which is held by NEN. This European Standard shall be given the status of a natio

20、nal standard, either by publication of an identical text or by endorsement, at the latest by June 2018, and conflicting national standards shall be withdrawn at the latest by June 2018. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent righ

21、ts. CEN shall not be held responsible for identifying any or all such patent rights. This document supersedes CEN ISO/TS 16407-1:2011. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association. According to the CEN-CENELEC Interna

22、l Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Irel

23、and, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Endorsement notice The text of ISO 16407-1:2017 has been approved by CEN as EN ISO 16407-1:2017 without any modific

24、ation. BS EN ISO 164071:2017ISO 16407-1:2017(E)Foreword ivIntroduction v1 Scope . 12 Normative references 23 Terms and definitions . 24 Abbreviated terms 45 Test suite structure 55.1 Structure . 55.2 Reference to conformance test specifications 55.3 Test purposes (TP) 65.3.1 TP definition convention

25、s 65.3.2 TP naming conventions 65.4 Conformance test report 7Annex A (normative) Test purposes (TP) for Front End 8Annex B (normative) Test purposes (TP) for Back End .93Annex C (normative) Data structures .97Annex D (normative) PCTR for Front End 99Annex E (normative) PCTR for Back End 104Bibliogra

26、phy . 108 ISO 2017 All rights reserved iiiContents PageBS EN ISO 164071:2017ISO 16407-1:2017(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carrie

27、d out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. IS

28、O collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different

29、approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).Attention is drawn to the possibility that some of the elements of this document may be t

30、he subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).An

31、y trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs a

32、dherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL: www.iso.org/iso/foreword.html.This document was prepared by Technical Committee ISO/TC 204, Intelligent transport systems.This first edition cancels and replaces ISO/TS 16407-1:2

33、011, which has been technically revised.The main changes compared to the previous edition are as follows: this document has been converted from a Technical Specification to an International Standard; this document has been amended to reflect changes to the underlying base standards, especially ISO 1

34、7575; this document contains major changes regarding data element changes introduced by ISO 17575-1 and ISO 17575-3, new test purposes related to protocol version handling and authenticated data elements, removed test purposes related to rules with respect to charging which are not anymore required

35、by ISO 17575-1, revised terms and definitions, and editorial and formal corrections, as well as changes to improve readability.A list of all parts in the ISO 16407 series can be found on the ISO website.iv ISO 2017 All rights reservedBS EN ISO 164071:2017ISO 16407-1:2017(E)IntroductionThis document,

36、 is part of a series of International Standards that supports interoperability of autonomous electronic fee collection (EFC) systems. Autonomous systems use satellite positioning, often combined with additional sensor technologies, such as gyroscopes, odometers and accelerometers, to localize the ve

37、hicle and to find its position on a map containing the charged geographic objects, such as charged roads or charged areas. From the charged objects, the vehicle characteristics, the time of day and other data that are relevant for describing road use, the tariff and ultimately, the road usage fee is

38、 determined.Autonomous on-board equiment (OBE) operates without relying on dedicated road-side infrastructure by employing wide-area technologies such as Global Navigation Satellite Systems (GNSS) and Cellular Communications Networks (CN). Therefore, autonomous systems can also be referred to as GNS

39、S/CN systems.Within the series of EFC standards, this document defines tests for conformity evaluation of Front End and Back End that comply with the requirements towards the charging specified in ISO 17575-1.This document is based on ISO 17575-1 and the ISO/IEC 9646 series of standards on conforman

40、ce test methodology. ISO 2017 All rights reserved vBS EN ISO 164071:2017Electronic fee collection Evaluation of equipment for conformity to ISO 17575-1 Part 1: Test suite structure and test purposes1 ScopeThe ISO 16407 series of standards specifies a suite of tests in order to assess the Front End a

41、nd Back End behaviour compliancy towards the requirements listed in ISO 17575-1. This document contains the definition of such tests in the form of test purposes, listing the required initial conditions, references and individual steps in a structured textual manner.Test purposes defined in this doc

42、ument reflect the structural and semantical requirements stated in ISO 17575-1: presence/absence of particular data elements; semantics related to various data elements: data group General (see ISO 17575-1:2016, 7.3); data group Security (see ISO 17575-1:2016, 7.4); data group Contract (see ISO 1757

43、5-1:2016, 7.5); data group Usage (see ISO 17575-1:2016, 7.6); data group Account (see ISO 17575-1:2016, 7.7); data group Versioning (see ISO 17575-1:2016, 7.8).With regard to the individual data sets and EFC attributes defined in ISO 17575-1, the test purposes have been organized into the test suite

44、 groups designated for the Front End and Back End, respectively.Besides the test purposes, this document also specifies proforma conformance test report templates for both the Front End and Back End test purposes.For more information regarding the requirements against which the conformance is evalua

45、ted in this document, see ISO 17575-1.Testing of the following behaviours and functionalities is outside of the scope of this document: dynamic behaviour, i.e. sequence of messages and triggering events that can be exchanged/happen to fulfil certain charging scenarios; profiles and business logic bu

46、ilt on top of particular pricing schemas; as ISO 17575-1 does not specify any Behaviour Invalid of Front End and Back End, BI test purposes are not applicable for any test purpose group.INTERNATIONAL STANDARD ISO 16407-1:2017(E) ISO 2017 All rights reserved 1BS EN ISO 164071:2017ISO 16407-1:2017(E)2

47、 Normative referencesThe following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including a

48、ny amendments) applies.ISO 17575-1:2016, Electronic fee collection Application interface definition for autonomous systems Part 1: Charging3 Terms and definitionsFor the purposes of this document, the following terms and definitions apply.ISO and IEC maintain terminological databases for use in stan

49、dardization at the following addresses: IEC Electropedia: available at http:/www.electropedia.org/ ISO Online browsing platform: available at http:/www.iso.org/obp3.1area chargingcharging based on road usage within a given areaSOURCE: ISO 17575-1:2016, 3.13.2attributeaddressable package of data consisting of a single data element (3.9) or structured sequences of data elementsSOURCE: ISO 17575-1:2016, 3.23.3authenticatordata, possibly encrypted, that is used for authenticationSOURCE: EN