EN ISO 5173-2010 en Destructive tests on welds in metallic materials - Bend tests (Incorporates Amendment A1 2011)《金属材料焊接点无损检测试验 弯曲试验［代替 CEN EN 910］》.pdf

《EN ISO 5173-2010 en Destructive tests on welds in metallic materials - Bend tests (Incorporates Amendment A1 2011)《金属材料焊接点无损检测试验 弯曲试验［代替 CEN EN 910］》.pdf》由会员分享，可在线阅读，更多相关《EN ISO 5173-2010 en Destructive tests on welds in metallic materials - Bend tests (Incorporates Amendment A1 2011)《金属材料焊接点无损检测试验 弯曲试验［代替 CEN EN 910］》.pdf（26页珍藏版）》请在麦多课文档分享上搜索。

1、BS EN ISO5173:2010ICS 25.160.40NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDDestructive tests onwelds in metallicmaterials Bend tests+A1:2011National forewordThis British Standard is the UK implementation of EN ISO 5173:2010+A1:2011. It is identical to ISO 51

2、73:2009, incorporating amendment 1:2011. It supersedes BS EN ISO 5173:2010 which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee WEE/2, Destructive Testing of Welds.A list of organizations represented on this committee can be obtained on request to its secre

3、tary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.BS EN ISO 5173:2010+A1:2011This British Standardwas published under theauth

4、ority of the StandardsPolicy and StrategyCommittee on 30 April2010 BSI 2011Amendments/corrigenda issued since publicationDate Comments 30 November 2011 Implementation of ISO amendment 1:2011 with CEN endorsement A1:2011: Replaced section 5.6.7.3, a), 2)ISBN 978 0 580 74924 7EUROPEAN STANDARD NORME E

5、UROPENNE EUROPISCHE NORM EN ISO 5173:2010+A1 November 2011ICS 25.160.40 Supersedes EN 910:1996English Version Destructive tests on welds in metallic materials - Bend tests (ISO 5173:2009) Essais destructifs des soudures sur matriaux mtalliques -Essais de pliage (ISO 5173:2009) Zerstrende Prfungen vo

6、n Schweinhten an metallischen Werkstoffen - Biegeprfungen (ISO 5173:2009) This European Standard was approved by CEN on 18 March 2010. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national s

7、tandard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any ot

8、her language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmar

9、k, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATI

10、ON EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 5173:2010: E3 Foreword The text of ISO 5173:2009 has been prepared by Technical Committ

11、ee ISO/TC 44 “Welding and allied processes” of the International Organization for Standardization (ISO) and has been taken over as EN ISO 5173:2010 by Technical Committee CEN/TC 121 “Welding” the secretariat of which is held by DIN. This European Standard shall be given the status of a national stan

12、dard, either by publication of an identical text or by endorsement, at the latest by October 2010, and conflicting national standards shall be withdrawn at the latest by October 2010. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights

13、. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 910:1996. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Au

14、stria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom

15、. Endorsement notice The text of ISO 5173:2009 has been approved by CEN as a EN ISO 5173:2010 without any modification. Foreword to amendment A1This document (EN ISO 5173:2010/A1:2011) has been prepared by Technical Committee ISO/TC 44 “Welding and allied processes“ in collaboration with Technical C

16、ommittee CEN/TC 121 “Welding” the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2012, and conflicting national standards shall be withdrawn at the latest

17、 by May 2012. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standard

18、s organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Pola

19、nd, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of ISO 5173:2009/Amd 1:2011 has been approved by CEN as a EN ISO 5173:2010/A1:2011 without any modification. BS EN ISO 5173:2010+A1:2011 EN ISO 5173:2010+A1:2011 (E)iiiContents P

20、age Foreword iv 1 Scope 1 2 Terms and definitions .1 3 Principle2 4 Symbols and abbreviated terms 2 4.1 Symbols 2 4.2 Abbreviated terms .2 4.3 Figures corresponding to the abbreviations 3 5 Preparation of test specimens .6 5.1 General6 5.2 Location 6 5.3 Marking .6 5.4 Heat treatment and/or ageing.6

21、 5.5 Extraction .7 5.6 Specimen size 7 6 Conditions of testing.10 6.1 Etching10 6.2 Testing 10 6.3 Diameter of former and roller .16 6.4 Distance between rollers 16 6.5 Bending angle 16 6.6 Bending elongation .16 7 Test results.16 8 Test report 17 Annex A (informative) Example of a test report .18 B

22、S EN ISO 5173:2010+A1:2011 EN ISO 5173:2010+A1:2011 (E) ISO 2011iv Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical

23、 committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with

24、 the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft Intern

25、ational Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may

26、be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 5173 was prepared by Technical Committee ISO/TC 44, Welding and allied processes, Subcommittee SC 5, Testing and inspection of welds. This third edition cancels and replaces the seco

27、nd edition (ISO 5173:2000) which has been technically revised. Requests for official interpretations of any aspect of this International Standard should be directed to the Secretariat of ISO/TC 44/SC 5 via your national standards body, of which a complete listing can be found at www.iso.org. BS EN I

28、SO 5173:2010+A1:2011 EN ISO 5173:2010+A1:2011 (E) ISO 2011INTERNATIONAL STANDARD 1Destructive tests on welds in metallic materials Bend tests 1 Scope This International Standard specifies a method for making transverse root, face and side bend tests on test specimens taken from butt welds, butt weld

29、s with cladding (subdivided into welds in clad plates and clad welds) and cladding without butt welds, in order to assess ductility and/or absence of imperfections on or near the surface of the test specimen. It also gives the dimensions of the test specimen. In addition, this International Standard

30、 specifies a method for making longitudinal root and face bend tests to be used instead of transverse bend tests for heterogeneous assemblies when base materials and/or filler metal have a significant difference in their physical and mechanical properties in relation to bending. This International S

31、tandard applies to metallic materials in all forms of product with welded joints made by any fusion arc welding process. 2 Terms and definitions For the purposes of this document, the following terms and definitions apply. 2.1 transverse face bend test specimen for a butt weld TFBB specimen for whic

32、h the surface in tension is the side that contains the greater width of the weld or the side from which the welding arc was first applied, applicable to transverse butt weld specimens See Figure 1. 2.2 transverse root bend test specimen for a butt weld TRBB specimen for which the surface in tension

33、is the side opposite to that of the face butt weld bend test specimen, applicable to transverse butt weld specimens See Figure 2. 2.3 transverse side bend test specimen for a butt weld SBB specimen for which the surface in tension is a cross-section of the weld See Figure 3. 2.4 longitudinal face te

34、st specimen for a butt weld root bend test specimen for a butt weld LFBB LRBB specimen whose direction is parallel to butt weld direction, applicable to face and root bend specimens See Figure 4. BS EN ISO 5173:2010+A1:2011 EN ISO 5173:2010+A1:2011 (E) ISO 20112 2.5 face bend test specimen for cladd

35、ing without a butt weld FBC specimen for which the cladding is in tension, applicable to both transverse and longitudinal specimens See Figure 5. 2.6 side bend test specimen for cladding without a butt weld SBC specimen for which the cross-section of the cladding overlay is in tension, applicable to

36、 both transverse and longitudinal specimens See Figure 6. 2.7 face bend test specimen for cladding with a butt weld side bend test specimen for cladding with a butt weld FBCB SBCB specimen for which the cladding is in tension or for which the cross-section of the cladding overlay is in tension and w

37、hich contains a butt weld See Figures 7 and 8. 3 Principle Submitting a test specimen, taken transversely or longitudinally from a welded joint, to plastic deformation by bending it, without reversing the bending direction, in such a way that one of the surfaces or cross-sections of the welded joint

38、 is in tension. Unless otherwise specified, the test shall be carried out at an ambient temperature of (23 5) C. The test shall be made in accordance with one of the methods described in Clause 6. 4 Symbols and abbreviated terms 4.1 Symbols See Table 1 and Figures 1 to 15. 4.2 Abbreviated terms TFBB

39、 Transverse face bend test specimen for a butt weld TRBB Transverse root bend test specimen for a butt weld SBB Transverse side bend test specimen for a butt weld LFBB Longitudinal face bend test specimen for a butt weld LRBB Longitudinal root bend test specimen for a butt weld FBC Face bend test sp

40、ecimen for cladding without a butt weld SBC Side bend test specimen for cladding without a butt weld FBCB Face bend test specimen for cladding with a butt weld SBCB Side bend test specimen for cladding with a butt weld BS EN ISO 5173:2010+A1:2011 EN ISO 5173:2010+A1:2011 (E) ISO 20113Table 1 Symbols

41、 and designations Symbol Designation Unit A minimum percentage elongation after fracture required by the material specification % b width of the test specimen mm b1width of outside fusion line mm d diameter of the former or the inner roller mm D outside diameter of the pipeamm l distance between the

42、 rollers mm Lfinitial distance between contact of the roller and the centre line of the weld mm Looriginal gauge length mm Lsmaximum width of the weld after machining mm Lttotal length of the test specimen mm r radius of the test specimen edges mm R radius of the rollers mm t thickness of the test p

43、iece mm tcthickness of the cladding mm tsthickness of the test specimen mm twthickness of base material under cladding mm bending angle aThe term “pipe”, alone or in combination, is used to mean “pipe”, “tube” or “hollow section (without rectangular cross section)”. 4.3 Figures corresponding to the

44、abbreviations Figures 1 to 8 represent bend test specimens for butt welds and cladding. Figure 1 Transverse face bend test specimen for a butt weld (TFBB) BS EN ISO 5173:2010+A1:2011 EN ISO 5173:2010+A1:2011 (E) ISO 20114 Figure 2 Transverse root bend test specimen for a butt weld (TRBB) Figure 3 Tr

45、ansverse side bend test specimen for a butt weld (SBB) Figure 4 Longitudinal bend test specimen for a butt weld (LFBB and LRBB) BS EN ISO 5173:2010+A1:2011 EN ISO 5173:2010+A1:2011 (E) ISO 20115Figure 5 Face bend test specimen for cladding without a butt weld (FBC) Figure 6 Side bend test specimen f

46、or cladding without a butt weld (SBC) Figure 7 Face bend test specimen for cladding with a butt weld (FBCB) BS EN ISO 5173:2010+A1:2011 EN ISO 5173:2010+A1:2011 (E) ISO 20116 Figure 8 Side bend test specimen for cladding with a butt weld (SBCB) 5 Preparation of test specimens 5.1 General Specimens s

47、hall be prepared in such a manner that the preparation does not affect either the base material or the weld metal. 5.2 Location For transverse bend testing of butt welds, the test specimen shall be taken transversely from the welded joint of the manufactured product or from the welded test piece in

48、such a way that after machining the weld axis will remain in the centre of the test specimen or at a suitable position for testing. For longitudinal bend testing of butt welds, the test specimen shall be taken longitudinally from the welded joint of the manufactured product or from the welded test p

49、iece. The location and orientation of bend test specimens of cladding material shall be specified by the application standard or by agreement between the contracting parties. 5.3 Marking Each test piece shall be marked to identify its exact location in the manufactured product or in the joint from which it has been removed. If required by the relevant application standard, the direction of working (e.g. rolling or extrusion) shall be marked. Each test specimen shall be marked to identify its exact location in the test piece from which it