EN 60317-62-2012 en Specifications for particular types of winding wires - Part 62 Polyester glass fibre wound minimum class 200 resin or varnish impregnated bare or enamelled rect.pdf

《EN 60317-62-2012 en Specifications for particular types of winding wires - Part 62 Polyester glass fibre wound minimum class 200 resin or varnish impregnated bare or enamelled rect.pdf》由会员分享，可在线阅读，更多相关《EN 60317-62-2012 en Specifications for particular types of winding wires - Part 62 Polyester glass fibre wound minimum class 200 resin or varnish impregnated bare or enamelled rect.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationSpecifications for particular types of winding wiresPart 62: Polyester glass fibre wound,minimum class 200 resin or varnishimpregnated, bare or enamelled rectangular copper wire,

2、 temperature index 200BS EN 60317-62:2012National forewordThis British Standard is the UK implementation of EN 60317-62:2012. It isidentical to IEC 60317-62:2012.The UK participation in its preparation was entrusted to Technical CommitteeGEL/55, Winding wires.A list of organizations represented on t

3、his committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisions of acontract. Users are responsible for its correct application. The British Standards Institution 2012Published by BSI Standards Limited 2012ISBN 978 0 580 68352 7ICS 2

4、9.060.10Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of the StandardsPolicy and Strategy Committee on 31 October 2012.Amendments issued since publicationAmd. No. Date Text affectedBRITISH STANDARDBS EN 60317-6

5、2:2012EUROPEAN STANDARD EN 60317-62 NORME EUROPENNE EUROPISCHE NORM September 2012 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Management Centre: Avenue Marnix 17, B - 1000 Brussels 2

6、012 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 60317-62:2012 E ICS 29.060.10 English version Specifications for particular types of winding wires - Part 62: Polyester glass fibre wound, minimum class 200 resin or varnish impr

7、egnated, bare or enamelled rectangular copper wire, temperature index 200 (IEC 60317-62:2012) Spcifications pour types particuliers de fils de bobinage - Partie 62: Fil de section rectangulaire en cuivre nu ou maill, guip de fibres de verre avec polyester de classe dau moins 200, imprgnes de vernis

8、ou de rsine, dindice de temprature 200(CEI 60317-62:2012) Technische Lieferbedingungen fr bestimmte Typen von Wickeldrhten - Teil 62: Flachdrhte aus Kupfer, blank oder lackisoliert und umhllt mit Polyesterglasgewebe, imprgniert mit Harz oder Lack oder unimprgniert, Temperaturindex 200 (IEC 60317-62:

9、2012) This European Standard was approved by CENELEC on 2012-08-16. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliograp

10、hical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsi

11、bility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland,

12、 Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 60317-62:2012EN 60317-62:2

13、012 - 2 - Foreword The text of document 55/1323/FDIS, future edition 1 of IEC 60317-62, prepared by IEC/TC 55 “Winding wires“ was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 60317-62:2012. The following dates are fixed: latest date by which the document has to be impleme

14、nted at national level by publication of an identical national standard or by endorsement (dop) 2013-05-16 latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2015-08-16 This standard is to be read in conjunction with EN 60317-0-8:2012. Attention is d

15、rawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC and/or CEN shall not be held responsible for identifying any or all such patent rights. Endorsement notice The text of the International Standard IEC 60317-62:2012 was approved by CENELEC

16、as a European Standard without any modification. In the official version, for Bibliography, the following notes have to be added for the standards indicated: IEC 60264 Series NOTE Harmonised as EN 60264 Series (not modified). IEC 60317 Series NOTE Harmonised as EN 60317 Series (not modified). IEC 60

17、851 Series NOTE Harmonised as EN 60851 Series (not modified). BS EN 60317-62:2012- 3 - EN 60317-62:2012 Annex ZA (normative) Normative references to international publications with their corresponding European publications The following documents, in whole or in part, are normatively referenced in t

18、his document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE When an international publication has been modified by common modifications, in

19、dicated by (mod), the relevant EN/HD applies. Publication Year Title EN/HD Year IEC 60317-0-8 2012 Specifications for particular types of winding wires - Part 0-8: General requirements - Polyester glass fibre wound, resin or varnish impregnated or not impregnated, bare or enamelled rectangular coppe

20、r wire EN 60317-0-8 2012 BS EN 60317-62:2012 2 60317-62 IEC:2012 CONTENTS INTRODUCTION . 5 1 Scope . 6 2 Normative references . 6 3 Terms, definitions, general notes and appearance 6 3.1 Terms and definitions 6 3.2 General notes 6 3.2.1 Methods of test 6 3.2.2 Winding wire 7 3.3 Appearance . 7 4 Dim

21、ensions 7 5 Electrical resistance . 7 6 Elongation 7 7 Springiness 7 8 Flexibility and adherence 7 9 Heat shock . 7 10 Cut-through 8 11 Resistance to abrasion . 8 12 Resistance to solvents 8 13 Breakdown voltage . 8 14 Continuity of insulation . 8 15 Temperature index . 8 16 Resistance to refrigeran

22、ts . 8 17 Solderability . 8 18 Heat or solvent bonding 8 19 Dielectric dissipation factor . 8 20 Resistance to transformer oil 8 23 Pin hole test . 8 30 Packaging 9 Bibliography 10 BS EN 60317-62:201260317-62 IEC:2012 5 INTRODUCTION This part of IEC 60317 is one of a series which deals with insulate

23、d wires used for windings in electrical equipment. The series has three groups describing: 1) Winding wires Test methods (IEC 60851); 2) Specifications for particular types of winding wires (IEC 60317); 3) Packaging of winding wires (IEC 60264). BS EN 60317-62:2012 6 60317-62 IEC:2012 SPECIFICATIONS

24、 FOR PARTICULAR TYPES OF WINDING WIRES Part 62: Polyester glass fibre wound, minimum class 200 resin or varnish impregnated, bare or enamelled rectangular copper wire, temperature index 200 1 Scope This part of IEC 60317 specifies the requirements of polyester glass fibre wound, resin or varnish imp

25、regnated, bare or enamelled rectangular copper winding wire, temperature index 200. NOTE For this type of wire, the heat shock test is inappropriate and therefore a heat shock temperature cannot be established. Consequently, a class based on the requirements for temperature index and heat shock temp

26、erature cannot be specified. The range of nominal conductor dimensions covered by this standard is: width: min. 2,0 mm; max. 16,0 mm; thickness: min. 0,80 mm; max. 5,60 mm. The specified combinations of width and thickness as well as the specified width/thickness ratio are according to IEC 60317-0-8

27、. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any ame

28、ndments) applies. IEC 60317-0-8:2012, Specifications for particular types of winding wires Part 0-8: General requirements Polyester glass fibre wound, resin or varnish impregnated or not impregnated, bare or enamelled rectangular copper wire 3 Terms, definitions, general notes and appearance 3.1 Ter

29、ms and definitions For the purposes of this document, the terms and definitions given in 3.1 of IEC 60317-0-8:2012 apply. 3.2 General notes 3.2.1 Methods of test Subclause 3.2 of IEC 60317-0-8:2012 applies. In case of inconsistency between IEC 60317-0-8 and this standard, IEC 60317-62 shall prevail.

30、 BS EN 60317-62:201260317-62 IEC:2012 7 3.2.2 Winding wire The enamelled wire shall have a temperature index of at least 200 and shall be agreed between purchaser and supplier. The temperature index of the wire is dependent upon the type of impregnating agent used. The impregnating agent applied to

31、the polyester glass fibre shall contain silicone and have a minimum temperature index of 200. The covering shall have one of the following grades of thickness: PG1: one polyester glass fibre covering over a bare conductor; PG2: two polyester glass fibre coverings over a bare conductor: grade 1 PG1:

32、one polyester glass fibre covering (GL1) over grade 1 enamelled conductor (Grade 1); grade 1 PG2: two polyester glass fibre coverings (GL2) over grade 1 enamelled conductor (Grade 1); grade 2 PG1: one polyester glass fibre covering (GL1) over grade 2 enamelled conductor (Grade 2); grade 2 PG2: two p

33、olyester glass fibre coverings (GL2) over grade 2 enamelled conductor (Grade 2). 3.3 Appearance Subclause 3.3 of IEC 60317-0-8:2012 applies. 4 Dimensions Clause 4 of IEC 60317-0-8:2012 applies. 5 Electrical resistance Clause 5 of IEC 60317-0-8:2012 applies. 6 Elongation Clause 6 of IEC 60317-0-8:201

34、2 applies. 7 Springiness Clause 7 of IEC 60317-0-8:2012 applies. 8 Flexibility and adherence Clause 8 of IEC 60317-0-8:2012 applies. 9 Heat shock Test inappropriate. BS EN 60317-62:2012 8 60317-62 IEC:2012 10 Cut-through Test inappropriate. 11 Resistance to abrasion Test inappropriate. 12 Resistance

35、 to solvents Test inappropriate. 13 Breakdown voltage Clause 13 of IEC 60317-0-8:2012 applies. 14 Continuity of insulation Test inappropriate. 15 Temperature index Clause 15 of IEC 60317-0-8:2012 applies. 16 Resistance to refrigerants Test inappropriate. 17 Solderability Test inappropriate. 18 Heat

36、or solvent bonding Test inappropriate. 19 Dielectric dissipation factor Test inappropriate. 20 Resistance to transformer oil Test inappropriate. 23 Pin hole test Test inappropriate BS EN 60317-62:201260317-62 IEC:2012 9 30 Packaging Clause 30 of IEC 60317-0-8:2012 applies. BS EN 60317-62:2012 10 603

37、17-62 IEC:2012 Bibliography IEC 60264 (all parts), Packaging of winding wires IEC 60317 (all parts), Specifications for particular types of winding wires IEC 60851 (all parts), Winding wires Test methods _ BS EN 60317-62:2012This page deliberately left blankBSI is the independent national body respo

38、nsible for preparing British Standards and other standards-related publications, information and services. It presents the UK view on standards in Europe and at the international level. BSI is incorporated by Royal Charter. British Standards and other standardisation products are published by BSI St

39、andards Limited.British Standards Institution (BSI)raising standards worldwideBSI389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards and PASs are periodically updated by amendment or revision. Users of British Standards and PASs should make sure that they poss

40、ess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using British Standards would inform the Secretary of the technical committee responsible, the identity of

41、which can be found on the inside frontcover. Similary for PASs, please notify BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers BSI Subscribing Members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions

42、of British Standards and PASs.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy versions of standards directly using acredit card from the BSI Shop on the website addition all orders for BSI, international and foreign standards publicationscan be

43、addressed to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In response to orders for international standards, BSI will supply the British Standard implementation of the relevant international standard, unless otherwise requested.Information on standardsBSI provides a

44、wide range of information on national, Europeanand international standards through its Knowledge Centre.Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005Email: BSI Subscribing Members are kept up to date with standards developments and receive substantial discounts on the purchase priceof standards.

45、 For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards and PASs via British Standards Online can be found at information about British Standards is available on th

46、e BSI website at www.bsi- the data, software and documentation set out in all British Standards and other BSI publications are the property of and copyrighted by BSI, or some person or entity that own copyright in the information used (such as the international standardisation bodies) has formally l

47、icensed such information to BSI for commerical publication and use. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without pri

48、or written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Department.Tel: +44 (0)20 8996 7070Email: