EN 60317-56-2012 en Specifications for particular types of winding wires - Part 56 Solderable fully insulated (FIW) zero-defect polyurethane enamelled round copper wire with nomina.pdf

《EN 60317-56-2012 en Specifications for particular types of winding wires - Part 56 Solderable fully insulated (FIW) zero-defect polyurethane enamelled round copper wire with nomina.pdf》由会员分享，可在线阅读，更多相关《EN 60317-56-2012 en Specifications for particular types of winding wires - Part 56 Solderable fully insulated (FIW) zero-defect polyurethane enamelled round copper wire with nomina.pdf（13页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationSpecifications for particular types of winding wires Part 56: Solderable fully insulated (FIW) zero-defect polyurethane enamelled round copper wire, with nominal conducter diamet

2、er of 0,040 mm to 1,600 mm, class 180BS EN 60317-56:2012National forewordThis British Standard is the UK implementation of EN 60317-56:2012. It isidentical to IEC 60317-56:2012.The UK participation in its preparation was entrusted to Technical CommitteeGEL/55, Winding wires.A list of organizations r

3、epresented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisions of acontract. Users are responsible for its correct application. The British Standards Institution 2012Published by BSI Standards Limited 2012ISBN 978 0 5

4、80 61692 1ICS 29.060.10 Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of the StandardsPolicy and Strategy Committee on 31 July 2012.Amendments issued since publicationAmd. No. Date Text affectedBRITISH STANDARD

5、BS EN 60317-56:2012EUROPEAN STANDARD EN 60317-56 NORME EUROPENNE EUROPISCHE NORM June 2012 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Management Centre: Avenue Marnix 17, B - 1000 Br

6、ussels 2012 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 60317-56:2012 E ICS 29.060.10 English version Specifications for particular types of winding wires - Part 56: Solderable fully insulated (FIW) zero-defect polyurethane en

7、amelled round copper wire with nominal conductor diameter of 0,040 mm to 1,600 mm, class 180 (IEC 60317-56:2012) Spcifications pour types particuliers de fils de bobinage - Partie 56: Fil brasable de section circulaire, isol en continu, en cuivre maill avec polyurthane sans dfaut disolation lectriqu

8、e, avec diamtre nominal de conducteur compris entre 0,040 mm et 1,600 mm, classe 180 (CEI 60317-56:2012) Technische Lieferbedingungen fr bestimmte Typen von Wickeldrhten - Teil 56: Isolationsfehlerfreie Runddrhte (FIW) aus Kupfer, verzinnbar, lackisoliert mit Polyurethan, mit Nenndurchmesser von 0,0

9、40 mm bis 1,600 mm, Klasse 180 (IEC 60317-56:2012) This European Standard was approved by CENELEC on 2012-06-19. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without an

10、y alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other la

11、nguage made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, t

12、he Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 60317-56:2012EN 6031

13、7-56:2012 - 2 - Foreword The text of document 55/1311/FDIS, future edition 1 of IEC 60317-56, prepared by IEC/TC 55 “Winding wires“ was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 60317-56:2012. The following dates are fixed: latest date by which the document has to be i

14、mplemented at national level by publication of an identical national standard or by endorsement (dop) 2013-03-19 latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2015-06-19 This standard is to be read in conjunction with EN 60317-0-7:2012. Attentio

15、n is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC and/or CEN shall not be held responsible for identifying any or all such patent rights. Endorsement notice The text of the International Standard IEC 60317-56:2012 was approved by CE

16、NELEC as a European Standard without any modification. BS EN 60317-56:2012- 3 - EN 60317-56:2012 Annex ZA (normative) Normative references to international publications with their corresponding European publications The following documents, in whole or in part, are normatively referenced in this doc

17、ument and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE When an international publication has been modified by common modifications, indicated

18、 by (mod), the relevant EN/HD applies. Publication Year Title EN/HD Year IEC 60317-0-7 2012 Specifications for particular types of winding wires - Part 0-7: General requirements - Fully insulated (FIW) zero-defect enamelled round copper wire with nominal conductor diameter of 0,040 mm to 1,600 mm EN

19、 60317-0-7 2012 BS EN 60317-56:2012 2 60317-56 IEC:2012 CONTENTS INTRODUCTION . 5 1 Scope . 6 2 Normative references . 6 3 Terms and definitions, general notes and appearance 6 4 Dimensions 7 5 Electrical resistance . 7 6 Elongation 7 7 Springiness 7 8 Flexibility and adherence 7 9 Heat shock . 7 10

20、 Cut-Through . 7 11 Resistance to abrasion (for nominal diameters of 0,250 mm up to and including 1,000 mm) 7 12 Resistance to solvents 8 13 Breakdown voltage . 8 14 Continuity of insulation . 8 15 Temperature index . 8 16 Resistance to refrigerants . 8 17 Solderability . 9 18 Heat or solvent bondin

21、g 9 19 Dielectric dissipation factor . 9 20 Resistance to transformer oil 9 21 Loss of mass 9 23 Pin-hole test . 9 30 Packaging 9 Table 1 Resistance to abrasion 8 BS EN 60317-56:201260317-56 IEC:2012 5 INTRODUCTION This part of IEC 60317 is one of a series which deals with insulated wires used for w

22、indings in electrical equipment. The series has three groups describing: 1) winding wires Test methods (IEC 60851); 2) specifications for particular types of winding wires (IEC 60317); 3) packaging of winding wires (IEC 60264). BS EN 60317-56:2012 6 60317-56 IEC:2012 SPECIFICATIONS FOR PARTICULAR TY

23、PES OF WINDING WIRES Part 56: Solderable fully insulated (FIW) zero-defect polyurethane enamelled round copper wire with nominal conductor diameter of 0,040 mm to 1,600 mm, class 180 1 Scope This part of IEC 60317 specifies the requirements of solderable fully insulated (FIW) zero-defect enamelled r

24、ound copper wire, class 180, with a single coating based on polyurethane resin, which may be modified providing it retains its chemical identity and satisfies all the required technical specifications. The range of nominal conductor diameters of the wires covered by this standard is as follows: Grad

25、e of FIW 3 to FIW 08: 0,040 mm up to and including 0,067 mm; Grade of FIW 3 to FIW 09: 0,071 mm up to and including 0,355 mm; Grade of FIW 3 to FIW 08: 0,375 mm up to and including 0,475 mm; Grade of FIW 3 to FIW 07: 0,500 mm up to and including 0,750 mm; Grade of FIW 3 to FIW 06: 0,800 mm up to and

26、 including 1,000 mm; Grade of FIW 3 to FIW 05: 1,060 mm up to and including 1,600 mm. The nominal conductor diameters are specified in IEC 60317-0-7. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its applica

27、tion. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60317-0-7:2012, Specifications for particular types of winding wires Part 0-7: General requirements Fully insulated (FIW) zero-def

28、ect enamelled round copper wire with nominal conductor diameter of 0,040 mm to 1,600 mm 3 Terms and definitions, general notes and appearance 3.1 Terms and definitions For the purposes of this document, the terms and definitions given in 3.1 of IEC 60317-0-7:2012 apply. 3.2 General notes 3.2.1 Metho

29、ds of test Subclause 3.2 of IEC 60317-0-7:2012 applies. In case of inconsistencies between IEC 60317-0-7 and this standard, IEC 60317-56 shall prevail. BS EN 60317-56:201260317-56 IEC:2012 7 3.2.2 Winding wire A modified resin is one that has undergone a chemical change or contains one or more addit

30、ives to enhance certain performance or application characteristics. Class 180 is a thermal class requiring a temperature index of at least 180 C and a heat shock temperature of at least 200 C. The temperature in C corresponding to the temperature index is not necessarily the temperature recommended

31、as the wires temperature in use, since this temperature depends on many factors, including the type of electrical equipment involved. 3.3 Appearance Subclause 3.3 of IEC 60317-0-7:2012 applies. 4 Dimensions Clause 4 of IEC 60317-0-7:2012 applies. 5 Electrical resistance Clause 5 of IEC 60317-0-7:201

32、2 applies. 6 Elongation Clause 6 of IEC 60317-0-7:2012 applies. 7 Springiness Clause 7 of IEC 60317-0-7:2012 applies. 8 Flexibility and adherence Clause 8 of IEC 60317-0-7:2012 applies. 9 Heat shock Clause 9 of IEC 60317-0-7:2012 applies. The minimum heat shock temperature shall be 200 C. 10 Cut-Thr

33、ough No failure shall occur within 2 minutes at 245 C. 11 Resistance to abrasion (for nominal diameters of 0,250 mm up to and including 1,000 mm) The wire shall satisfy the requirements in Table 1. For intermediate nominal diameters, the amount of resistance to abrasion for the next larger nominal d

34、iameter shall apply. BS EN 60317-56:2012 8 60317-56 IEC:2012 Table 1 Resistance to abrasion Nominal conductor diameter Resistance to abrasion Grade of FIW 3 to FIW 9 Minimum of average value Minimum mm N N 0,250 4,10 3,50 0,280 4,40 3,70 0,315 4,75 4,00 0,355 5,10 4,30 0,400 5,45 4,60 0,450 5,80 4,9

35、0 0,500 6,20 5,25 0,560 6,65 5,60 0,630 7,10 6,00 0,710 7,60 6,45 0,800 8,10 6,90 0,900 8,70 7,40 1,000 9,30 7,90 12 Resistance to solvents Clause 12 of IEC 60317-0-7:2012 applies. 13 Breakdown voltage Clause 13 of IEC 60317-0-7:2012 applies. The elevated temperature shall be 180 C. 14 Continuity of

36、 insulation Clause 14 of IEC 60317-0-7:2012 applies. 15 Temperature index Clause 15 of IEC 60317-0-7:2012 applies. The minimum temperature index shall be 180. 16 Resistance to refrigerants Test inappropriate. BS EN 60317-56:201260317-56 IEC:2012 9 17 Solderability The temperature of the solder bath

37、shall be (390 5) C. The maximum immersion time (in seconds) shall be the following multiple of the nominal conductor diameter (in millimetres) with a minimum of 4 s: All grades of FIW 18 s/mm The surface of the tinned wire shall be smooth and free of holes and enamel residue. 18 Heat or solvent bond

38、ing Test inappropriate. 19 Dielectric dissipation factor A test method shall be agreed between the user and the supplier. 20 Resistance to transformer oil Test inappropriate. 21 Loss of mass Test inappropriate. 23 Pin-hole test Clause 23 of IEC 60317-0-7:2012 applies. 30 Packaging Clause 30 of IEC 6

39、0317-0-7:2012 applies. _ BS EN 60317-56:2012This page deliberately left blankBSI is the independent national body responsible for preparing British Standards and other standards-related publications, information and services. It presents the UK view on standards in Europe and at the international le

40、vel. BSI is incorporated by Royal Charter. British Standards and other standardisation products are published by BSI Standards Limited.British Standards Institution (BSI)raising standards worldwideBSI389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards and PASs

41、 are periodically updated by amendment or revision. Users of British Standards and PASs should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambi

42、guity while using British Standards would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside frontcover. Similary for PASs, please notify BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers BSI Subscribing Membe

43、rs an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of British Standards and PASs.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy versions of standards directly using acredit card

44、 from the BSI Shop on the website addition all orders for BSI, international and foreign standards publicationscan be addressed to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In response to orders for international standards, BSI will supply the British Standard im

45、plementation of the relevant international standard, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, Europeanand international standards through its Knowledge Centre.Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005Email: BSI Subscribing Membe

46、rs are kept up to date with standards developments and receive substantial discounts on the purchase priceof standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British

47、Standards and PASs via British Standards Online can be found at information about British Standards is available on the BSI website at www.bsi- the data, software and documentation set out in all British Standards and other BSI publications are the property of and copyrighted by BSI, or some person

48、 or entity that own copyright in the information used (such as the international standardisation bodies) has formally licensed such information to BSI for commerical publication and use. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details