EN 50155-2007 en Railway applications - Electronic equipment used on rolling stock (Incorporating corrigendum May 2010)《轨道交通 铁路车辆用电子设备 合并勘误表2010年5月》.pdf

《EN 50155-2007 en Railway applications - Electronic equipment used on rolling stock (Incorporating corrigendum May 2010)《轨道交通 铁路车辆用电子设备 合并勘误表2010年5月》.pdf》由会员分享，可在线阅读，更多相关《EN 50155-2007 en Railway applications - Electronic equipment used on rolling stock (Incorporating corrigendum May 2010)《轨道交通 铁路车辆用电子设备 合并勘误表2010年5月》.pdf（46页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARDBS EN 50155:2007Railway applications Electronic equipment used on rolling stockICS 45.060.10g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g

2、47g36g58IncorporatingcorrigendumMay 2010National forewordThis British Standard is the UK implementation of EN 50155:2007, incorporating corrigendum May 2010. It supersedes BS EN 50155:2001 which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee GEL/9, Railway

3、electrotechnical applications.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standar

4、d cannot confer immunity from legal obligations.BS EN 50155:2007This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 August 2007 BSI 2010Amendments/corrigenda issued since publicationDate Comments 31 July 2010 Implementation of CENELEC corrigen

5、dum May 2010. Replacement of Annex ZZISBN 978 0 580 71755 0EUROPEAN STANDARD EN 50155 NORME EUROPENNE EUROPISCHE NORM July 2007 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Sec

6、retariat: rue de Stassart 35, B - 1050 Brussels 2007 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 50155:2007 E English version Railway applications - Electronic equipment used on rolling stock Applications ferroviaires - Equipe

7、ments lectroniques utiliss sur le matriel roulant Bahnanwendungen - Elektronische Einrichtungen auf Schienenfahrzeugen This European Standard was approved by CENELEC on 2007-03-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving

8、 this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official ver

9、sions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees o

10、f Austria, Belgium, Bulgaria, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United King

11、dom. ICS 45.060.10 Supersedes EN 50155:2001 + A1:2002Incorporating corrigendum May 2010- 2 - Foreword This European Standard was prepared by the Technical Committee CENELEC TC 9X, Electrical and electronic applications for railways. The text of the draft was submitted to the Unique Acceptance Proced

12、ure and was approved by CENELEC as EN 50155 on 2007-03-01. This European Standard supersedes EN 50155:2001 + A1:2002. This EN 50155:2007 has been aligned with the new EN 50121 series and addresses some Portuguese comments. The following dates were fixed: latest date by which the EN has to be impleme

13、nted at national level by publication of an identical national standard or by endorsement (dop) 2008-03-01 latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 2010-03-01 This European Standard has been prepared under a mandate given to CENELEC by the Europe

14、an Commission and the European Free Trade Association and covers essential requirements of EC Directives 96/48/EC and 2001/16/EC. See Annex ZZ. _ BS EN 50155:2007EN 50155:2007 (E)- 3 -Contents 1 Scope .5 2 Normative references 5 3 Definitions7 4 Environmental service conditions of operation.8 4.1 No

15、rmal service conditions 8 4.2 Special service conditions10 5 Electrical service conditions.10 5.1 Power supply.10 5.2 Supply .12 5.3 Installation .12 5.4 Surges electrostatic discharge and transient burst susceptibility tests 12 5.5 Electromagnetic compatibility.12 6 Reliability, maintainability and

16、 expected useful life 12 6.1 Equipment reliability .12 6.2 Useful life.13 6.3 Maintainability 13 6.4 Maintenance levels 13 6.5 Built-in diagnostics.14 6.6 Automatic test equipment 14 6.7 Alternative methods for fault diagnosis.14 6.8 Purpose built test equipment and special tools.14 7 Design 15 7.1

17、General15 7.2 Detailed practices - Hardware15 7.3 Detailed practices - Software .17 7.4 Equipment features19 8 Components.20 8.1 Procurement20 8.2 Application.21 9 Construction 21 9.1 Equipment construction .21 9.2 Component mounting.21 9.3 Electrical connections 22 9.4 Internal flexible wiring (ele

18、ctrical and optical)23 9.5 Flexible printed and strip wiring 23 9.6 Printed board-flexible and rigid.24 9.7 Protective coatings for printed board assemblies .24 9.8 Identification 25 9.9 Mounting25 9.10 Cooling and ventilation.25 9.11 Materials and finishes 26 BS EN 50155:2007EN 50155:2007 (E)- 4 -

19、10 Safety .26 10.1 General26 10.2 Functional safety26 10.3 Personnel safety26 11 Documentation 26 11.1 Supply and storage of documentation 26 11.2 Hardware and software documentation 26 11.3 Documentation requirements .28 12 Testing .29 12.1 Categories of tests.29 12.2 List of tests30 Annex A (infor

20、mative) List of subclauses in which agreement between the parties (e.g. user and manufacturer) is mentioned 40 Bibliography 41 Annex ZZ (informative) Coverage of Essential Requirements of EC Directives 42 Figure 1 - System interfacing with the typical EMC areas A, B and C . 16 Figure 2 - Supply over

21、voltage 34 Figure 3 - Alternative test for supply overvoltage. 35 Table 1 - Ambient temperature 9 Table 2 - List of tests 30 BS EN 50155:2007EN 50155:2007 (E)- 5 -1 Scope This standard applies to all electronic equipment for control, regulation, protection, supply, etc., installed on rail vehicles a

22、nd associated with: - either the accumulator battery of the vehicle; - or a low voltage power supply source with or without a direct connection to the contact system (transformer, potentiometer device, auxiliary supply); with the exception of electronic power circuits, which conform to EN 50207. Thi

23、s standard covers the conditions of operation, design, construction, and testing of electronic equipment, as well as basic hardware and software requirements considered necessary for competent, reliable equipment. Additional requirements in other standards or individual specifications may complement

24、 this standard, if they are justified. Specific requirements related to practices necessary to assure defined levels of functional safety are to be determined in accordance with 4.6.3.1 and 4.6.3.2 of EN 50126 and its informative Annex A. Software safety integrity level of 1 or higher shall only be

25、considered when it is shown that a residual safety risk remains and that it has to be carried by the software driven programmable electronic system. In such a case (i.e. software safety integrity level 1 or higher), EN 50128 is applicable. For the purpose of this standard, electronic equipment is de

26、fined as equipment mainly composed of semiconductor devices and recognized associated components. These components will mainly be mounted on printed boards. NOTE Sensors (current, voltage, speed, etc.) and firing unit printed board assemblies for power electronic devices are covered by this standard

27、. Complete firing units are covered by EN 50207. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including an

28、y amendments) applies. EN 50121-3-2 2000 Railway Applications - Electromagnetic compatibility Part 3-2: Rolling stock Apparatus EN 50125-1 1999 Railway Applications Environmental conditions for equipment Part 1: Equipment on board rolling stock EN 50126 Series Railway applications - The specificatio

29、n and demonstration of Reliability, Availability, Maintainability and Safety (RAMS) EN 50128 2001 Railway applications - Communication, signalling and processing systems -Software for railway control and protection systems EN 50163 1995 Railway Applications - Supply voltages of traction systems EN 5

30、0207 2000 Railway applications - Electronic power converters for rolling stock (IEC 61287-1:1995, related) EN 60068 Series Environmental testing (IEC 60068 series) EN 60068-2-1 1993 Environmental testing Part 2: Tests Test A: Cold (IEC 60068-2-1:1990) EN 60068-2-2 1993 Environmental testing Part 2:

31、Tests Test B: Dry heat (IEC 60068-2-2:1974 + IEC 60068-2-2A:1976) EN 60068-2-30 2005 Environmental testing Part 2: Tests Test Db and guidance: Damp heat, cyclic (12 + 12 hour cycle) (IEC 60068-2-30:2005) BS EN 50155:2007EN 50155:2007 (E)- 6 - EN 60077 Series Railway applications Electrotechnical equ

32、ipment for rolling stock (IEC 60077 series, modified) EN 60249-2-15 1994 Base materials for printed circuits Part 2: Specifications - Specification No. 15: Flexible copper-clad polyimid film, of defined flammability (publication withdrawn) EN 60297 Series Mechanical structures for electronic equipme

33、nt - Dimensions of mechanical structures of the 482,6 mm (19 in) series (IEC 60297 series) EN 60352 Series Solderless connections (IEC 60352 series) EN 60352-1 1997 Solderless connections Part 1: Wrapped connections - General requirements, test methods and practical guidance (IEC 60352-1:1997) EN 60

34、352-2 2006 Solderless connections Part 2: Crimped connections - General requirements, test methods and practical guidance (IEC 60352-2:2006) EN 60529 1991 Degrees of protection provided by enclosures (IP Codes) (IEC 60529:1989) EN 61000-4-4 2004 Electromagnetic compatibility (EMC) Part 4-4: Testing

35、and measurement techniques - Electrical fast transient/burst immunity test (IEC 61000-4-4:2004) EN 61082 Series Preparation of documents used in electrotechnology (IEC 61082 series) EN 61249 Series Materials for printed boards and other interconnecting structures (IEC 61249 series) EN 61249-2-7 2002

36、 Materials for printed boards and other interconnecting structures Part 2-7: Reinforced base materials, clad and unclad - Epoxide woven E-glass laminated sheet of defined flammability (vertical burning test), copper-clad (IEC 61249-2-7:2002) EN 61249-2-10 2003 Materials for printed boards and other

37、interconnecting structures Part 2-10: Reinforced base materials, clad and unclad - Cyanate ester, brominated epoxide, modified or unmodified, woven E-glass reinforced laminated sheets of defined flammability (vertical burning test), copper-clad (IEC 61249-2-10:2003) EN 61373 1999 Railway application

38、s - Rolling stock equipment - Shock and vibration tests (IEC 61373:1999) EN 62326 Series Printed boards EN 123000 1991 Generic specification - Printed boards EN 123200 1992 Sectional specification - Single and double sided printed boards with plated-through holes EN 123300 1992 Sectional specificati

39、on - Multi-layer printed boards EN 123400 1992 Sectional specification - Flexible printed boards without through connections EN 123500 1992 Sectional specification - Flexible printed boards with through connections EN ISO 9000-3 1997 Quality management and quality assurance standards Part 3: Guideli

40、nes for the application of ISO 9001 to the development, supply and maintenance of software (ISO 9000-3:1991) EN ISO 9001 Quality management systems - Requirements (ISO 9001) EN ISO 9002 Quality systems - Model for quality assurance in production, installation and servicing (ISO 9002) IEC 60605 Serie

41、s Equipment reliability testing IEC 60617 Database Graphical symbols for diagrams BS EN 50155:2007EN 50155:2007 (E)- 7 -3 Definitions For the purposes of this standard, the following definitions apply: 3.1 printed board base material cut to size containing all holes and bearing at least one conducti

42、ve pattern. Printed boards are typically subdivided according to: - their structure (e.g. single and double-sided, multilayers) - the nature of the base material (e.g. rigid, flexible) 3.2 printed board assembly printed board with electrical and mechanical components and/or other printed boards atta

43、ched to it with all manufacturing processes, soldering, coating, etc., completed 3.3 plug-in unit unit which plugs into a subrack and is supported by guides. These units can be of various types, ranging from a printed board with components mounted in a frame or box type unit, designed with a plug-in

44、 connection 3.4 subrack structural unit for housing printed board assemblies and/or plug-in units 3.5 rack free-standing or fixed structure for supporting electrical or electronic equipment (e.g. subracks) 3.6 cubicle any enclosure for housing electrical and/or electronic equipment 3.7 line replacea

45、ble unit unit designed to be exchanged as a result of on-vehicle fault diagnosis, e.g. a subrack, or plug-in unit 3.8 performance check short form performance test which is carried out during and after environmental tests, sufficient to prove that the equipment is within its operational limits, and

46、that it has survived an environmental test 3.9 control system voltage supply voltage supply used to power the vehicle control equipment The supply may be derived from a vehicle battery. The battery may be charged from battery chargers, auxiliary inverters and motor-alternator or motor-generator sets

47、 with associated electronic regulations Where the control system voltage supply is derived from a battery, the nominal and rated control system voltages are defined in 5.1. Where no battery is fitted, the nominal control system voltage is the normal controlled level of that voltage 3.10 vehicle wiri

48、ng all wiring which can be connected to the control system voltage supply, wherever located, and all other wiring external to the electronic equipment under consideration BS EN 50155:2007EN 50155:2007 (E)- 8 - 3.11 supply overvoltage electrical disturbance to the control system voltage supply caused

49、 by equipment controlling that supply. A supply overvoltage will occur as an increase in the level of the control system voltage supply 3.12 surge non-periodic and relatively short positive or negative (or both) variable (voltage or current) between two steady states It may be produced by the normal operation of equipment within the vehicle, caused generally by the discharge of energy when inductive circuits are switched It may be present either on the control system voltage supply, or on wiring connected directly to switched induc