EN 16804-2015 en Diving equipment - Diving open heel fins - Requirements and test methods《潜水装备 潜水可调节脚蹼 要求和测试方法》.pdf

《EN 16804-2015 en Diving equipment - Diving open heel fins - Requirements and test methods《潜水装备 潜水可调节脚蹼 要求和测试方法》.pdf》由会员分享，可在线阅读，更多相关《EN 16804-2015 en Diving equipment - Diving open heel fins - Requirements and test methods《潜水装备 潜水可调节脚蹼 要求和测试方法》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationBS EN 16804:2015Diving equipment Divingopen heel fins Requirementsand test methodsBS EN 16804:2015 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 16804:2015.The UK participation in its preparation was entrusted to TechnicalCommittee PH/

2、4/7, Underwater breathing apparatus.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institu

3、tion 2016.Published by BSI Standards Limited 2016ISBN 978 0 580 87845 9ICS 97.220.40Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 29 February 2016.Amendments/cor

4、rigenda issued since publicationDateT e x t a f f e c t e dBS EN 16804:2015EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 16804 December 2015 ICS 97.220.40 English Version Diving equipment - Diving open heel fins - Requirements and test methods quipement de plonge - Palmes de plonge non chauss

5、antes - Exigences et mthodes dessais Tauch-Zubehr - Taucherflossen - Anforderungen und Prfverfahren This European Standard was approved by CEN on 16 November 2015. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standa

6、rd the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English,

7、 French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulg

8、aria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Tu

9、rkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2015 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members.

10、 Ref. No. EN 16804:2015 EBS EN 16804:2015EN 16804:2015 (E) 2 Contents Page European foreword . 3 1 Scope 4 2 Terms and definitions . 4 3 Design requirements . 4 3.1 General 4 3.2 Surfaces in contact with the foot 4 3.3 Heel band . 4 4 Tests . 5 4.1 Visual inspection . 5 4.2 Heel band test . 5 4.2.1

11、Resistance to slipping 5 4.2.2 Resistance to slipping out or detachment 5 4.2.3 Permanent linear deformation 5 4.3 Practical performance . 5 5 Marking . 5 6 Information supplied by the manufacturer . 6 BS EN 16804:2015EN 16804:2015 (E) 3 European foreword This document (EN 16804:2015) has been prepa

12、red by Technical Committee CEN/TC 136 “Sports, playground and other recreational facilities and equipment”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by

13、 June 2016, and conflicting national standards shall be withdrawn at the latest by June 2016. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent

14、rights. According to the CEN/CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, Fra

15、nce, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 16804:2015EN 16804:2015 (E) 4 1 Scope This European Standard applies to o

16、pen heel fins for diving where the user is breathing underwater. The purpose of this European Standard is the specification of minimum safety requirements. 2 Terms and definitions For the purposes of this document, the following terms and definitions apply. 2.1 open heel fin fin that is retained on

17、the users foot by a heel band Note 1 to entry: The term “fins” will be used in the current standard for open heel fins. 2.2 heel band device allowing the diving fin to be maintained on the foot of the user Note 1 to entry: The heel band might be adjustable. 2.3 buckle device allowing adjustment of t

18、he heel band tension 3 Design requirements 3.1 General The fin shall be designed to be maintained on the users feet during normal condition of use. Test in accordance with Clause 4. 3.2 Surfaces in contact with the foot The fins shall not have any projecting parts, or corners and edges, which may in

19、jure the user. Test in accordance with 4.1. 3.3 Heel band Heel band shall be designed so that the fins can be donned and removed easily. Test in accordance with 4.3. If adjustable, when wetted, the heel band of a fin shall withstand a pull force of 150 N, during 10 s, without slipping. Test in accor

20、dance with 4.2.1. Any heel band shall withstand a pull force of 200 N, during 10 s, without detaching or slipping out from the buckle and/or attachment. Test in accordance with 4.2.2. The permanent linear deformation of the heel band shall not be greater than 5 % when tested at a pull force of 100 N

21、 for 10 s, measurement being carried out 30 min after pulling. Test in accordance with 4.2.3. BS EN 16804:2015EN 16804:2015 (E) 5 4 Tests 4.1 Visual inspection Visual inspection shall be conducted at normal visual acuity. The visual inspection shall include tactual examination and the assessment of

22、the device marking, information supplied by the manufacturer and any safety data sheet. 4.2 Heel band test 4.2.1 Resistance to slipping The fins shall be suspended on a support body having a radius of 20 mm by means of the heel band. Each heel band adjustment shall be set to its midpoint. A tensile

23、force of 150 N is applied to the open-heel fin in the direction of the heel, for duration of 10 s. 4.2.2 Resistance to slipping out or detachment The fins shall be suspended on a support body having a radius of 20 mm by means of the heel band. Each heel band adjustment shall be set to its midpoint.

24、A tensile force of 200 N is applied to the open-heel fin in the direction of the heel, for duration of 10 s. 4.2.3 Permanent linear deformation Test three samples: one end of the band is fixed; apply the force of 100 N to the free end of the heel strap for 10 s. Measure the permanent linear deformat

25、ion 30 min after the pull test. 4.3 Practical performance During the test the fins will be subjectively assessed by three test subjects and their comments on the following points shall be recorded after the test: donning and doffing of the fins as well as adjustment of all straps (if applicable), wi

26、thout help on land; jumping into water (feet first) from the height of 1,5 m; swimming at a depth of at least 1 m for 15 m. During jumping and swimming the fin shall not be damaged and shall not detach or become loose. 5 Marking Each fin shall be marked according to the relevant following items: a)

27、the manufacturer shall be identified by name, trade mark or other means of identification; b) size (if applicable); c) type-identifying mark; d) the number of this European standard. BS EN 16804:2015EN 16804:2015 (E) 6 6 Information supplied by the manufacturer The information supplied by the manufa

28、cturer shall be in the official language(s) of the country of destination and shall be attached to the fins or given in or on the packaging. The information supplied by the manufacturer shall contain all information necessary for trained and qualified persons on instruction how to use and select the

29、 fins. This page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Li

30、mited.British Standards Institution (BSI)BSI Group Headquarters389 Chiswick High Road London W4 4AL UKAbout usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in

31、our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organizatio

32、n needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through ou

33、r website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.SubscriptionsOur range of subscription services are designed to make using standards easie

34、r for you. For further information on our subscription products go to British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date. You can

35、 keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive the lat

36、est hard copy of your standards when theyre revised or replaced. To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as few or as ma

37、ny users as you wish. With updates supplied as soon as theyre available, you can be sure your documentation is current. For further information, email .RevisionsOur British Standards and other publications are updated by amendment or revision. We continually improve the quality of our products and s

38、ervices to benefit your business. If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre.CopyrightAll the data, software and documentation set out in all British Standards and other BSI publications are the property of and copyrig

39、hted by BSI, or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI for commercial publication and use. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract

40、may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. Details and advice can be obtained from the Copyright & Licensing Department.Useful Contacts:Customer ServicesTel: +44 845 086 9001Email (orders): Email (enquiries): SubscriptionsTel: +44 845 086 9001Email: Knowledge CentreTel: +44 20 8996 7004Email: Copyright & LicensingTel: +44 20 8996 7070Email: NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW