EN 772-15-2000 en Methods of Test for Masonry Units - Part 15 Determination of Water Vapour Permeability of Autoclaved Aerated Concrete Masonry Units《砌块的试验方法 第15部分 热压处理过的加气混凝土砌块水蒸汽.pdf
《EN 772-15-2000 en Methods of Test for Masonry Units - Part 15 Determination of Water Vapour Permeability of Autoclaved Aerated Concrete Masonry Units《砌块的试验方法 第15部分 热压处理过的加气混凝土砌块水蒸汽.pdf》由会员分享,可在线阅读,更多相关《EN 772-15-2000 en Methods of Test for Masonry Units - Part 15 Determination of Water Vapour Permeability of Autoclaved Aerated Concrete Masonry Units《砌块的试验方法 第15部分 热压处理过的加气混凝土砌块水蒸汽.pdf(10页珍藏版)》请在麦多课文档分享上搜索。
1、 STD.BSI BS EN 772-15-ENGL 2000 Lb2qbhS OBbBA43 bT3 BRITISH STANDARD Methods of test for masonry units - Part 15: Determination of water vapour permeability of autoclaved aerated concrete masonry units The European Standard EN 772162000 has the status of a British Standard ICs 91.080.30; 91.100.30 N
2、O COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGET LAW BS EN 772-15:2000 STD-BSI BS EN 772-15-ENGL 2000 I lib29bb9 ObqLi 53T I BS EN 772-15:2000 Amd. No. Date National foreword Comments This British Standard is the official English language version of EN 772-152000. No British Standar
3、d is being superseded. The UK participation in its preparation was enlmsted by Technical Committee B/519, Masonry and associated tests, to Subcommittee B/519/1, Masonry units, which has the responsibility to: - aid enquirers to understand the text; - present to the responsible European committee any
4、 enquiries on the interpretation, or proposals for change, and keep the UK interests informed; - monitor related international and European developments and promulgate them in the UK A list of organizations represented on this subcommittee can be obtained on request to its secrew. Cross-references T
5、he British Standards which implement intemational or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A
6、British Standard does not purport to include ail the necessary provisions of a contsact. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a
7、8 mm to 10 mm may be appropriate for relatively impermeable specimens and 20mm to 50mm for more permeable specimens. The thickness shall be measured using calipers and shall be reported. O BSI 09-2000 Page 6 EN 772-15:2000 7.2 Sampling The method of sampling shall be in accordance with prEN 771-4. T
8、he minimum number of specimens shall be three, but a larger minimum number may be specified in the product specification, in which case that larger number shall be used. 8 Test procedure Note: Although there are no requirements for conditioning specimens before testing, it will take longer for the t
9、est to reach equilibrium if the specimens are far fiom being in an air dry condition at the start of the test. Set all the specimens in test cups (6.1) and seal the edges with an appropriate sealant (6.3) or sealing ring. If not previously done, determine the area of the specimen. For the upper hygr
10、oscopic range (wet cup method), control the water vapour pressure using the potassium nitrate solution (KNQ) (6.4). For the lower hygroscopic range (dry cup method), control the water vapour pressure using the lithium chloride solution (LiCl.Hz0) (6.5). In each case leave a small air-gap of approxim
11、ately 10 mm between the specimen and the surface of the solution, (see Figure 1). Place the cups in an enclosure (6.6) with a temperature of 20 “C f 2 “C and a relative humidity of 50 % f 5 % r.h. and which is large enough to ensure good air circulation. Weigh the cups at appropriate time intervals.
12、 Draw a graph with mass of the cup against time. If three points can be placed on one straight line, the conditions are considered to be stable, i.e. the quantity of water vapour passing through the specimen per unit time is constant. 9 Expression of test results From each graph determine the water
13、vapour flux, -. Calculate the water vapour permeance using the following equation: AG At where: Ap is taken from appropriate tables, (Pa). The water vapour permeability is given as the mean value to the nearest 1 % for the water vapour permeance multiplied by the thickness of specimen in metres to t
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- EN772152000ENMETHODSOFTESTFORMASONRYUNITSPART15DETERMINATIONOFWATERVAPOURPERMEABILITYOFAUTOCLAVEDAERATEDCONCRETEMASONRYUNITS
链接地址:http://www.mydoc123.com/p-712736.html