EN 604-1-1997 en Aluminium and Aluminium Alloys - Cast Forging Stock - Part 1 Technical Conditions for Inspection and Delivery《铝和铝合金 铸锻件坯 第1部分 检查和交付的技术条件》.pdf

《EN 604-1-1997 en Aluminium and Aluminium Alloys - Cast Forging Stock - Part 1 Technical Conditions for Inspection and Delivery《铝和铝合金 铸锻件坯 第1部分 检查和交付的技术条件》.pdf》由会员分享，可在线阅读，更多相关《EN 604-1-1997 en Aluminium and Aluminium Alloys - Cast Forging Stock - Part 1 Technical Conditions for Inspection and Delivery《铝和铝合金 铸锻件坯 第1部分 检查和交付的技术条件》.pdf（11页珍藏版）》请在麦多课文档分享上搜索。

1、STD-BSI BS EN bOq-L-ENGL 1777 = Lb2LibbS b32785 115 BRITISH STANDARD Aluminium and aluminium alloys - Cast forging stock Part 1. Technical conditions for inspection and delivery The European Standard EN 604-1 : 1997 has the status of a British Standard ICs 77.150.10 BS EN 604-1 : 1997 NO COPYING WIT

2、HOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW STD-BSI BS EN bO?4-L-ENGL 1777 m Lb2LibbS Ob3278b 051 m Amd. No. BS EN 604-1 : 1997 Date Text affected Committees responsible for this British Standard The prepasation of this British Standard was entrusted to Technical Committee NM5, Light me

3、tals and their alloys, upon which the following bodies were represented Aluminium Federation Aluminium Stockholders? Association Association of Light Alloy Refiners Limited Magnesium Industry Council Ministry of Defence The following bodies were also represented in the drafting of the standard, thro

4、ugh subcommittees and panels: Association of British Welded Aluminium lbe Makers Institution of Structural Engineers Metal Packaging Manuacturers? Association This British Standard, having been prepared under the direction of the Engineering Sector Board, was published under the authority of the Sta

5、ndards Board and comes into effect on 15 May 1997 O BSI 1997 The following BSI references relate to the work on this standard Committee reference NFE/35 Draft for comment 91/49169 DC ISBN O 680 27426 X I STD-BSI BS EN bOq-L-ENGL 1777 Lb2ibbS Ob32787 T78 BS EN 604-1 : 1997 Contents Page Committees re

6、sponsible Inside front cover National foreword 11 Foreword 2 Text of EN 604-1 3 O BSI 1997 1 STD-BSI BS EN bULi-L-ENGL 1797 M Lb24bb9 Ub32788 724 = BS EN 604-1 : 1997 National foreword This Part of BS EN 604 has been prepared by Technical Committee NFE/35 and is the English language version of EN 60

7、4-1 : 1997 Aluminium and aluminium alloys - Cast forging stock - Part 1 : Technical conditions for inspection and 77.140.90 Descriptors: Aluminium products, aluminium alloys, forgings, delivery condition, surface condition, quality control, tests, quality certificate English veision Aluminium and al

8、uminiwn alloys - Cast forging mk - Part 1: Ikhnid conditions for hspection and delivery Aluminium et alliages daluminium - Produits couls et destins la forge - Partie 1: Conditions techniques de contrle et de livraison Muminium und Muminiumlegierungen - Gegossenes Schmiedevormaterial - Teil 1: lkchn

9、ische Lieferbedingungen This European Standard was approved by CEN on 1996-12-22. CEN members are bound to comply with the CENKENELEC Internal Regulations which stipulate the conditions for givhg this European Standard the status of a donal standard without any alteration. Up-to-date lists and bibli

10、ographical references concerning such national standards may be obtained on application to the Central Secretanat or to any GEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by tsanslation under the responsibility of

11、a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. GEN members are the national standards bodies of Austria, Belgium, Denmark, Finland, Mce, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norwax Portugal, Spain

12、, Sweden, Switzerland and United Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fur Normung Central Secretariat: me de Stassart 36, B-1060 Brussels O 1997 Copyright reserved to GEN members. Ref. No. EN 604-1 : 1997 E STD*BSI BS EN hUi-L-ENGL 19

13、97 lb24bb9 Ob32770 582 m Page 2 EN 604-1 : 1997 Foreword This European Standard has been prepared by the Technical Committee CENflC 132, Aluminium and aluminium alloys, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publi

14、cation of an identical text or by endorsement at the latest by July 1997, and conflicting national standards shali be withdrawn at the latest by July 1997. This standard is Part 1 of a set of two standards. The other standard is: EN 604-2 Alumnium and duminium alloys - Cast forging stock - Fart2: To

15、kames on dimenswns and form According to the CENEENELEX Internal Regulations, the nationaJ standards organhtions of the following countries are bound to implement this European standard Austria, Belgium, Denmark, Finland, hce, Gemany, Greece, Iceland, Ireland, Ita ingot); b) the type and metallurgic

16、al condition of the material: - the designation of the duminium and aluminium alloy; - the metallurgical condition for delivery (as cast or homogenized); c) the number of this European Standara d) the dimensions of the product (thickness, width, length, diameter); e) quantity and, where applicable,

17、tolerances on quantity (see 6.6); f) any requirements for inspection documents; g) any special requirements agreed between the purchaser and supplier, e.g. requirement for degassing, filtration 5 Requirements 6.1 Production and manufacturing processes The production and manufacturing processes shall

18、 be left to the discretion of the producer. Unless it is explicitly stated otherwise in the order, no obligation shall be placed on the producer to use the same processes for subsequent and sllnilas orders. 5.2 Quality control The supplier shall be responsible for the performance of all inspection a

19、nd tests required by the relevant European Standard or specifcation, prior to shipment of the product. If the purchaser wishes to inspect the product at the suppliers works, he shall notify the supplier at the time of placing the order. 6.3 Chemical composition The chemical composition shall comply

20、with the requirements given in EN 573-3. If the purchaser requires content hits for elements not specified in the above standard, these limits shall be stated on the order, after agreement between purchaser and supplier. 5.4 Surface quality 6.4.1 Surface roughness The surface roughness of the produc

21、t shall, where applicable, be agreed between purchaser and supplier and stated on the order. O BSI 1997 STD-BSI BS EN bUL1-1-ENGL 1777 = Lb24bb7 Ob32772 355 Page 4 EN 604-1 : 1997 5.4.2 Sutface finish The products shall be free from defects likely to impair the final surface finish of forgings subse

22、quently produced. Whilst an operation designed to mask a defect shall not be permissible, the elimination of a superficial surface defect shail be pennissible, provided that the dimensional tolerances are observed. 6.5 Tolerances on dimensions and form %lemces on dimensions and form shall comply wit

23、h EN 604-2. The purchaser may only reject those products having dimensions not complying with the specified tolerances. 5.6 Tolerances on quantity The tolerances on quantity shall be +2i % unless otherwise agreed between purchaser and supplier. 5.7 Internal quality The product shall be free from int

24、ernal defects which may be detrimental to the quality of forgings subsequently produced. if special inspections or tests are required, these shall be agreed between purchaser and supplier. 6 lst method 6.1 Sampling 6.1.1 Chemical analysis The test piece for chemical analysis shall be taken at the ti

25、me of casting. The shape and condition of production (mould design, cooling rate, mass, etc.) of the test piece shall be so designed that the composition is homogeneous and be suitable for the method of analysis. 6.1.2 Number of test pieces At least one test piece shall be taken to represent each ca

26、st. 6.2 Test procedure 6.2.1 Chemical composition Methods of analysis shall be at the discretion of the supplier. In case of dispute concerning the chemical composition, reference analysis shall be carried out by the methods agreed between purchaser and supplier and the resdts obtained by these meth

27、ods shall be accepted If the check analysis is to be made on the cast product, as supplied, the possibility of segregation effects shall be recognized, particularly in the thicker cross-sections. In such instances, the location of the sample for check analysis shall be subject to prior agreement bet

28、ween purchaser and supplier. 6.2.2 Measurement of dimensions The dimensions shall be measured by means of measuring insments which are of the acc- required by the dimensions and dimensional tolerances. All dimensions shail be checked at the ambient temperature of the workshop or laboratory, and, in

29、case of dispute, at a temperature between 15 “C and 25 “C inclusive. 6.2.3 Surface roughness Where specified surface roughness measurement shall be carried out using a method agreed between purchaser and supplier. 6.2.4 Sutface finish Examination of surface appearance shall be carried out without th

30、e assistance of magnifyhg appamtus, on products before delivery. 7 Inspection documents 7.1 General If requested by the purchaser on the order, the supplier shall provide one of more of the following documents as applicable. These inspection documents are based on EN 10204 with modifications due to

31、the specific needs of aluminium and aluminium alloys. The requirements of 3.1.A, 3.1.B, 3.1.C are in conformity with EN 10204. The requirements of 7.2, 7.2.1, 7.2.2 and 7.3 are specific to aluminium products. 7.2 Documents established on the basis of inspections and tests performed by qualified pers

32、onnel who are involved in the manufacturing process and/or belong to the quality control department 7.2.1 Certcate of corlformity Document by which the producer certifies that according to inspections and results of representative tests the products for delivery comply with the relevant standards an

33、d with the additional requirements in the order, if any 7.2.2 Test report Document by which the producer certifies that the products for delivery comply with the requirements specified on the order. This document details the results of the current production controls caxried out on identical product

34、s made using the me method as the products for delivery but not necessarily on the products for delivery themselves. O BSI 1997 STD.BSI BS EN 604-1-ENGL 1997 m LbZLibbS b32773 291 W Page 5 EN 604-1 : 1997 7.3 Documents established on the basis of inspections and tests performed or supervised by qual

35、ified personnel organizationally independent from the manufacturing department, according to the requirements specified on the order and carried out on the products for delivery or on the relevant inspection lot Inspection certificates in accordance with EN 10204: - 3.1.A : certificate issued and va

36、lidated by an inspector designated by the official regulations, in accordance with these and the corresponding technical rules; - 3.1.B : certificate issued by the department independent of the manufacturing department and validated by an authorized representative of the producer independent of the

37、manufacturing - 3.1.C : certificate issued and validated by an authorized representative of the purchaser, in accordance with the specications of the order. O department; O BSI 1997 8 Marking Markhg of products shall be undertaken oniy when agreed upon between purchaser and suppiier and stated on th

38、e order or drawing. This marking shall not adversely affect the final use of the product. 9 Packaging Unless otherwise specified in European Standards relating to special products or specified in the order, the mode of packaging shall be determined by the supplier who shall take all suitable precaut

39、ions to ensure that, under the usual conditions of transportation, the products are delivered in a condition suitable for use. 10 Arbitration In cases of dispute concerning conformity with the requirements of this standard or specification cited on the order, before rejecting the products, testing s

40、hall be carried out by an arbitrator chosen by mutual agreement between purchaser and supplier. The arbitrators decision shall be final. STD*BSI BS EN b04-L-ENGL 1997 Lb24bb7 Ob3277L1 128 D BS EN 604-1 : 1997 List of references See national foreword. O BSI 1997 BS EN 604-1 : 1997 BSI 389 Chiswick Hi

41、gh Road London w4 4AL BSI - British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Contract requirements A British Standard doe

42、s not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or edit

43、ions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone nding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the responsible technical committee, the identity of which can be found on the insi

44、de front cover. Tel 0181 996 9000; Fax: 0181 996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be

45、addressed to Customer Services, Sales Department at Chiswick Tel O181 996 7000; Fax: 0181 996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on

46、standards BSI provides a wide range of information on national, European and international standards through its Library, the Standardline Database, the BSI Information Technology Service (BlTS) and its Technical Help to Exporters Service. Contact the Information Department at Chiswick Tel 0181 996

47、7111; Fax: O181 996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Customer Services, Membership at Chiswick Tel 0181 996 7002; Fax: 0181 996 7001.

48、Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the internationd standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitt

49、ed in any form or by any means - electronic, photocopying, recording or otherwise - without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manage