EN 4695-2017 en Aerospace series - Tie Rod with integrated bolts - Assembly Code G H and K.pdf

《EN 4695-2017 en Aerospace series - Tie Rod with integrated bolts - Assembly Code G H and K.pdf》由会员分享，可在线阅读，更多相关《EN 4695-2017 en Aerospace series - Tie Rod with integrated bolts - Assembly Code G H and K.pdf（24页珍藏版）》请在麦多课文档分享上搜索。

1、Aerospace series - Tie Rod with integrated bolts - Assembly Code G, H and KBS EN 4695:2017BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06EUROPEANSTANDARDNORME EUROPENNE EUROPISCHE NORMEN 4695 October 2017ICS 49.035EnglishVersionAerospace series - Tie Rod with integr

2、ated bolts -Assembly Code G, H and KSrie arospatiale - Bielle avecaxes intgrs- Codeassemblage G, H etKLuft- und Raumfahrt - Zug-Druck Stange mitintegrierten Bolzen - Variante G, H und K This European Standard was approved by CEN on 25 June 2016.CEN members are bound to comply with the CEN/CENELEC In

3、ternal Regulations which stipulate the conditions for giving thisEuropean Standard the status of a national standard without any alteration.Up-to-date lists and bibliographical referencesconcerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any

4、CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made bytranslation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC ManagementCentre has the same status as the officialversio

5、ns.CEN members are the nationalstandards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Pola

6、nd, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGCEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights of exploitat

7、ion in any form and by any means reservedworldwide for CENnational Members.Ref. No. EN 4695:2017 ENational forewordThis British Standard is the UK implementation of EN 4695:2017.The UK participation in its preparation was entrusted to Technical Committee ACE/12, Aerospace fasteners and fastening sys

8、tems.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2017 Published by BSI S

9、tandards Limited 2017ISBN 978 0 580 94030 9ICS 49.035Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 October 2017.Amendments/corrigenda issued since publicati

10、onDate Text affectedBRITISH STANDARDBS EN 4695:2017EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 4695 October 2017 ICS 49.035 English Version Aerospace series - Tie Rod with integrated bolts - Assembly Code G, H and K Srie arospatiale - Bielle avec axes intgrs - Code assemblage G, H et K Luft

11、- und Raumfahrt - Zug-Druck Stange mit integrierten Bolzen - Variante G, H und K This European Standard was approved by CEN on 25 June 2016. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a nati

12、onal standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A ver

13、sion in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus,

14、Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United

15、 Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 46

16、95:2017 EBS EN 4695:2017EN 4695:2017 (E) 2 Contents Page European foreword . 3 Introduction 4 1 Scope 5 2 Normative references 5 3 Requirements . 6 4 Assembly code definitions . 6 5 Materials . 8 6 Locking clips . 8 7 Fork and eye ends 10 8 Mass calculation of tie rods 16 9 Marking 17 10 Dimensions

17、. 18 11 Designation. 18 12 Technical specification . 18 Annex A (informative) Standard evolution form . 19 BS EN 4695:2017EN 4695:2017 (E) 3 European foreword This document (EN 4695:2017) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). Af

18、ter enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a

19、 national standard, either by publication of an identical text or by endorsement, at the latest by April 2018, and conflicting national standards shall be withdrawn at the latest by April 2018. Attention is drawn to the possibility that some of the elements of this document may be the subject of pat

20、ent rights. CEN shall not be held responsible for identifying any or all such patent rights. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus,

21、Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the Un

22、ited Kingdom. BS EN 4695:2017EN 4695:2017 (E) 4 Introduction Aerospace and Defence Standardization (ASD-STAN) draws attention to the fact that it is claimed that compliance with this document may involve the use of a patent. USA: US 8371767 China: CN 10104431 Japan: JP 4885140 Russia: RU 2389914 Sou

23、th Africa: ZA 2007/03913 Canada: 2584387 South Korea: 7011559 ASD-STAN takes no position concerning the evidence, validity and scope of this patent right. The holder of this patent right has assured ASD-STAN that he/she is willing to negotiate licences under reasonable and non-discriminatory terms a

24、nd conditions with applicants throughout the world. In this respect, the statement of the holder of this patent right is registered with ASD-STAN. Information may be obtained from: GMT Gummi-Metall-Technik GmbH Liechtersmatten 5 D-77815 Bhl TRIGUM Engineering GmbH Brunskamp 4 D-21220 Seevetal/Masche

25、n Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights other than those identified above. ASD-STAN shall not be held responsible for identifying any or all such patent rights. BS EN 4695:2017EN 4695:2017 (E) 5 1 Scope This standard spec

26、ifies the dimensions and tolerances of rod assemblies for aerospace applications with two adjustable ends with integrated bolts for interior and sub structure in the temperature range 55 C to 85 C. The rod ends should not be screwed completely apart. 2 Normative references The following documents, i

27、n whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. DIN 6799, Retaining washers for s

28、hafts1)DIN 65038-1, Aerospace Steel, nickel- and cobalt-alloy bars Technical specification1)EN 2424, Aerospace series Marking of aerospace products EN 3311, Aerospace series Titanium alloy TI-P64001 (Ti-6Al-4V) Annealed Bar for machining D 110 mm EN 4614, Aerospace series Spherical plain bearings in

29、 corrosion resisting steel with self-lubricating liner wide series Dimensions and loads Inch series EN 4691-1, Aerospace series Tie rod with integrated bolts Part 1: Technical specification EN 4692, Aerospace series Tie rod with integrated bolts Locking clip EN 10088-3, Stainless steels Part 3: Tech

30、nical delivery conditions for semifinished products, bars, rods, wire, sections and bright products of corrosion resisting steels for general purposes ISO 2768-1, General tolerances Part 1: Tolerances for linear and angular dimensions without individual tolerance indications ISO 2768-2, General tole

31、rances Part 2: Geometrical tolerances for features without individual tolerance indications ISO 8075, Aerospace series Surface treatment of hardenable stainless steel parts LN 9368-4, Aerospace Designation of surface treatments Part 4: Codes numbers for methods of anodic treatment1)LN 9368-7, Aerosp

32、ace Designation of surface treatments Part 7: Codes numbers for methods of organic coating1)LN 9499-1, Aerospace series Inserts, helical coil threads, screw-locking Class: 1100 MPa/235 C/425 C1)WL 1.4548 (all parts), Aerospace Precipitation-hardening stainless chromium-nickel-copper steel with appro

33、x. 0,05C-16Cr-4Cu-4Ni1)WL 3.1354 (all parts), Aerospace Wrought aluminium alloy with approx. 4,4Cu-1,5Mg-0,6Mn1)FAR/JAR/CS 25.853, Compartment Interiors2)1) Published by: Beuth Verlag GmbH www.beuth.de BS EN 4695:2017EN 4695:2017 (E) 6 3 Requirements 3.1 Configuration, dimensions, tolerances and mas

34、s 3.1.1 Configuration The configuration shall be in accordance with Figure 1, Figure 2 and Figure 3. 3.1.2 Dimensions, tolerances and mass Dimensions are in millimetres, tolerances and masses in accordance to Table 4, Table 5, Table 6 and Table 7. General tolerances shall be in accordance to ISO 276

35、8-mK. Missing dimensions are manufacturing options. 3.1.3 Technical requirements See EN 4691-1. 4 Assembly code definitions Assembly code G, H and K are shown in Figure 1, Figure 2 and Figure 3. For assembly code G, H and K: d1= 20,0 mm, SW = 22,2 mm and adjustable range for L1= 6,35 mm. Key 1 2 4 5

36、 6 7 and 8 The position numbers and the materials are shown in Table 1 and Table 2. Figure 1 Assembly code G 2) Published by: European Aviation Safety Agency, Postfach 101253, D-50452 Koeln, Germany. BS EN 4695:2017EN 4695:2017 (E) 7 Key 1 2 3 4 5 6 7 8 and 9 The position numbers and the materials a

37、re shown in Table 1 and Table 2. Figure 2 Assembly code H Key 1 3 4 5 6 8 and 9 The position numbers and the materials are shown in Table 1 and Table 2. Figure 3 Assembly code K BS EN 4695:2017EN 4695:2017 (E) 8 5 Materials See Table 1. Table 1 Material code C Position Description Material Surface t

38、reatment 1 Rod body Aluminium alloy according to WL 3.1354 T4 / T351 Anodized according to LN 9368-4-2000 and coating according to LN 9368-7-5023 and according to LN 9368-7-5106 2 Fork end Stainless steel according to WL 1.4548.4 DIN 65038-1 Passivated according to ISO 8075 3 Eye end 4 Locking clip

39、According to EN 4692 5 Insert 5.1 Titanium alloy 3.7165 according to EN 3311 Threat insert / Helicoil 5.2 According to LN 9499-1, screw-locking according to EN 4691-1:2012, Table 4 6 Washer Silicon rubber a(see EN 4691-1) 7 Bushes Titanium alloy 3.7165 according to EN 3311 8 Snap ring According to D

40、IN 6799, material 1.4122 per EN 10088-3 9 Bearing According to EN 4614 10 Anaerobic Adhesive for Locking + Activator (Position 1 with position 2 and position 3 M181,5) See EN 4691-1 Adhesive for example Methacrylate ester loctite 2701 Activator loctite 7649 aApproved per FAR/JAR/CS 25.853. 6 Locking

41、 clips Locking clip according EN 4692. Description: For the fork ends there are two different types of safety clip. For the eye end only one locking clip type A is available. Type A has only the function to fix the fork end, eye end against rotation, see Figure 4 and Figure 5. Type B also has the fu

42、nction to fix the fork end against rotation, see Figure 6 and Figure 7. The second function is the load transmission of tension and compression forces. No separate pin required. The locking clip B is available in right hand (RH) and left hand (LH) version. BS EN 4695:2017EN 4695:2017 (E) 9 Figure 4

43、Clip A Figure 5 Clip A Figure 6 Clip B (R)ight Figure 7 Clip B (L)eft BS EN 4695:2017EN 4695:2017 (E) 10 7 Fork and eye ends The fork end is shown in Figure 8, Figure 9 and the description of fork end for material code C and clip code A is shown in Table 2. Key aLocking clip according EN 4692 Figure

44、 8 Fork end BS EN 4695:2017EN 4695:2017 (E) 11 Key aLocking clip according EN 4692 Figure 9 Fork end only for size code 52 BS EN 4695:2017EN 4695:2017 (E) 12 Table 2 Description of fork end for material code C Dimensions in millimetres Size code Clip code a10a20B1B10 D2 d10 D20F10F20+0,1 0 0,5 0 0,0

45、13 50 A 13,1 8,72 19 25 26,8 6,350 11 24,8 21,0 51 11,20 52 22,5 20,60 35 7,938 28,3 30,4 Size code L1aL2L3L4(L4) Adjustable range Thread Size code locking clip b50 160-250 9,5 8 51 3,175 RH 01 LH 51 RH 01 LH 52 180-250 64,4 RH 02 LH aPossible length range for complete tie rod. bSee EN 4692 locking

46、clip. BS EN 4695:2017EN 4695:2017 (E) 13 The fork end is shown in Figure 10 and the description of fork end for material code C and clip code B is shown in Table 3. Key aLocking clip according EN 4692 Figure 10 Fork end BS EN 4695:2017EN 4695:2017 (E) 14 Table 3 Description of fork end for material

47、code C Dimensions in millimetres Size code aSize code b Clip code a10a20B2B10 D2 d10 D10 D20F10F20+0,1 0 0,5 0 0,013 0,038 0,076 60 (70) B 13,1 8,72 19 25 26,8 6,350 6,350 11 27 21,0 61 (71) 11,20 62 (72) 22,5 20,60 35 7,938 7,938 35 30,4 Size code aSize code bL1cL2L3L4(L4) Adjustable range Thread S

48、ize code locking clip d60 (70) 160-250 9,5 8 51 3,175 RH 4R 04L LH 61 (71) RH 04R 04L LH 62 (72) 180-250 64,4 RH 03R 03L LH aSize code for fork end with locking clip R, see EN 4692 locking clip. bSize code for fork end with locking clip L in brackets, see EN 4692 locking clip. cPossible length range

49、 for complete tie rod. dSee EN 4692 locking clip. BS EN 4695:2017EN 4695:2017 (E) 15 The eye end is shown in Figure 11 and the description of eye end for material code C is shown in Table 4. Key aLocking clip according EN 4692 Figure 11 Eye end Table 4 Description of eye end for material code C Dimensions in millimetres Size code A30B2 d2 D30F30L1cL2L4(L4) Adjustable range Thread Size code locking clipb0 0,013 0 0,05 8