EN 2257-1997 en Aerospace Series - Circular Tubes for Structures in Aluminium and Aluminium Alloys - Diameter 6 mm Less Than or Equal to D Less Than or Equal to 100 mm - Thickness .pdf

《EN 2257-1997 en Aerospace Series - Circular Tubes for Structures in Aluminium and Aluminium Alloys - Diameter 6 mm Less Than or Equal to D Less Than or Equal to 100 mm - Thickness .pdf》由会员分享，可在线阅读，更多相关《EN 2257-1997 en Aerospace Series - Circular Tubes for Structures in Aluminium and Aluminium Alloys - Diameter 6 mm Less Than or Equal to D Less Than or Equal to 100 mm - Thickness .pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、STD-BSI BS EN 2257-ENGL 1777 P lb2qbb7 Ob20133 b BRITISH STANDARD AEROSPACE SERIES Circular tubes for structures in aluminium and aluminium alloys - Diameter 6 mm 5 D 5 100 mm - Thickness 1 mm 5 a 5 6 mm - Dimensions The European Standard EN 2257 : 1997 has the staius of a British Standard ICs 49.04

2、0.20 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHI LAW 7- BS EN 2267 : 1997 STD*BSI BS EN 2257-ENGL 2777 m 2b2Libb7 Ob2013Li 585 m BS EN 2267 : 1997 This British Standard, having been prepared under the direction of the Engineering Sector Board, was published under the authority

3、 of the Standards Board and comes into effect on 15 June 1997 O BSI 1997 The following BSI references relate to the work on this standard Committee reference ACW61 Draft for comment 96702854 DC Committees responsible for this British Standard The preparation of this British Standard was entrusted to

4、 Technical Committee ACW61, Inspection and bting requirements for aerospace metallic materials, upon which the foilowing bodies were represented: Aluminium Federation British Investment Casting ?kade Association Copper Development Association Light Metal Founders Association Ministry of Defence Nati

5、onal Phpical Laboratmy Society of British Aerospace Companies Limited UK Steel Association Amendments issued since publication Amd. No. Date I Te* IsTectd ISBN O 880 26686 9 - STD-BSI BS EN 2257-ENGL 1997 m 1b24bb Ob20135 411 m BS EN 2257 : 1997 Contents page Committees responsible Inside front cove

6、r Nalionai foreword ii Foreword 2 Specification O Introduction 1 Scope 3 3 2 Nonnative references 3 3 Form 3 4 Recommended dimensions and mass 4 6 Tolerances 4 O BSI 1997 i STD*BSI BS EN 2257-ENGL 1777 Lb2LibbS Ob20L3b 358 BS EN 2257 : 1997 National foreword This British Standard has been prepared b

7、y Technical Committee ACW61 and is the English language version of EN 2257 : 1997 Aerospace series - Circular tubes for structures in duminium and duminium alloys - DEameter 6 mm 5 D 5 100 mm - Thi only applicable to tubes supplied in fixed lengths Diameter 6SDS 100 Table 4 Straightness deviation Y,

8、 on any length X, 1) 17 5.2 Geometric tolerances - Straightness 5.2.1 See EN 3848. Method of measurement and symbols 5.2.2 Tolerances See table 5. d .,. I 1) x* = 1 O00 I STDmBSI BS EN 2257-ENGL 1777 lb24bb7 Ob20L42 b51 R BS EN 2257 : 1997 BSI 389 Chiswick High Road London w4 4AL BSI - British Stand

9、ards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the intemaiional level. It is incorporated by Royal Charter. Contract requirements A British Standard does not purport to include all the necessary

10、 provisions of a contra Fax: 0181 996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For dem of these and other benefits contact Customer Services, Membershq at Chiswick Tel: 0181 996 7002; Fax: 0

11、181 996 7001. Copyright Copyright subsists in aii BSI publications. BSI also holds the copynght, in the UK, of the publications of the international standarmon bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or

12、tsansmitted in any form or by any means - electronic, photocopying, recording or otherwise - without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If thes

13、e details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copynght Manager, BSI, 389 Chiswick High Road, London W4 4AL