ECMA 314-2001 Private Integrated Services Network (PISN) - Inter-Exchange Signalling Protocol - Call Identification and Call Linkage Additional Network Feature (2nd Edition)《专用综合业务.pdf

《ECMA 314-2001 Private Integrated Services Network (PISN) - Inter-Exchange Signalling Protocol - Call Identification and Call Linkage Additional Network Feature (2nd Edition)《专用综合业务.pdf》由会员分享，可在线阅读，更多相关《ECMA 314-2001 Private Integrated Services Network (PISN) - Inter-Exchange Signalling Protocol - Call Identification and Call Linkage Additional Network Feature (2nd Edition)《专用综合业务.pdf（62页珍藏版）》请在麦多课文档分享上搜索。

1、 Standard ECMA-314 2nd Edition - December 2001 Standardizing Information and Communication Systems Private Integrated Services Network (PISN) - Inter-Exchange Signalling Protocol - Call Identification and Call Linkage Additional Network Feature Phone: +41 22 849.60.00 - Fax: +41 22 849.60.01 - URL:

2、http:/www.ecma.ch - Internet: helpdeskecma.ch . Standard ECMA-314 2nd Edition - December 2001 Standardizing Information and Communication Systems Private Integrated Services Network (PISN) - Inter-Exchange Signalling Protocol - Call Identification and Call Linkage Additional Network Feature (QSIG-CI

3、DL) Phone: +41 22 849.60.00 - Fax: +41 22 849.60.01 - URL: http:/www.ecma.ch - Internet: helpdeskecma.ch IW Ecma-314.doc 14-01-02 10,51 . Brief History This Standard is one of a series of ECMA Standards defining services and signalling protocols applicable to Private Integrated Services Networks (PI

4、SNs). The series uses ISDN concepts as developed by ITU-T and conforms to the framework of International Standards for Open Systems Interconnection as defined by ISO/IEC. This particular Standard specifies the signalling protocol for use at the Q reference point in support of the Call Identification

5、 and Call Linkage Additional Network Feature. The protocol defined in this Standard forms part of the PSS1 protocol (informally known as QSIG). This Standard is based upon the practical experience of ECMA member companies and the results of their active and continuous participation in the work of IS

6、O/IEC JTC1, ITU-T, ETSI and other international and national standardization bodies. It represents a pragmatic and widely based consensus. Compared to the 1st Edition of Standard ECMA-314 (published by ECMA in September 2000), this 2nd Edition incorporates migration to ASN.1 version 1997 as well as

7、changes in order to achieve complete alignment with International Standard ISO/IEC 13870:2001(E) published by ISO/IEC in 2001. Adopted as 2nd Edition of Standard ECMA-314 by the General Assembly of December 2001. - i - Table of contents 1 Scope 1 2 Conformance 1 3 References (normative) 1 4 Definiti

8、ons 3 4.1 External definitions 3 4.2 Other definitions 4 4.2.1 CIDL PINX 4 4.2.2 CIDL Transit PINX 4 5 Acronyms 4 6 Signalling protocol for the support of ANF-CIDL 4 6.1 ANF-CIDL description 4 6.2 ANF-CIDL operational requirements 5 6.2.1 Provision/Withdrawal 5 6.2.2 Requirements on an Originating P

9、INX 5 6.2.3 Requirements on a CIDL PINX 5 6.2.4 Requirements on a CIDL Transit PINX 5 6.3 ANF-CIDL coding requirements 6 6.3.1 Operations 6 6.3.2 Information elements 7 6.3.3 Messages 7 6.4 ANF-CIDL state definitions 7 6.4.1 States at a Originating PINX 7 6.4.2 States at a CIDL PINX 8 6.4.3 States a

10、t a CIDL Transit PINX 8 6.5 ANF-CIDL signalling procedures 8 6.5.1 Actions at a Originating PINX 8 6.5.2 Procedures at the CIDL PINX 9 6.5.3 Actions at a CIDL Transit PINX 11 6.6 ANF-CIDL impact of interworking with public ISDNs 11 6.7 ANF-CIDL impact of interworking with non-ISDNs 11 6.8 Protocol I

11、nteractions between ANF-CIDL and other supplementary services and ANFs 11 6.8.1 Calling Name Identification Presentation (SS-CNIP) 12 6.8.2 Connected Name Identification Presentation (SS-CONP) 12 6.8.3 Completion of Calls to Busy Subscribers (SS-CCBS) 12 6.8.4 Completion of Calls on No Reply (SS-CCN

12、R) 12 6.8.5 Call Forwarding Unconditional (SS-CFU) 12 6.8.6 Call Forwarding Busy (SS-CFB) 12 6.8.7 Call Forwarding No Reply (SS-CFNR) 12 - ii - 6.8.8 Call Deflection (SS-CD) 12 6.8.9 Call Transfer (SS-CT) 13 6.8.10 Path Replacement (ANF-PR) 14 6.8.11 Advice Of Charge (SS-AOC) 14 6.8.12 Call Offer (S

13、S-CO) 14 6.8.13 Do Not Disturb (SS-DND) 14 6.8.14 Do Not Disturb Override (SS-DNDO) 14 6.8.15 Recall (SS-RE) 14 6.8.16 Call Intrusion (SS-CI) 14 6.8.17 Call Interception (ANF-CINT) 15 6.8.18 Transit Counter (SS-TC) 15 6.8.19 Route Restriction Class (ANF-RRC) 15 6.8.20 Authentication of the PISN (SS-

14、WTAN) 15 6.8.21 Authentication of a WTM user (SS-WTAT) 15 6.8.22 Wireless Terminal Location Registration (SS-WTLR) 15 6.8.23 Wireless Terminal Mobility Incoming Call (ANF-WTMI) 15 6.8.24 Wireless Terminal Mobility Outgoing Call (ANF-WTMO) 15 6.8.25 Message Waiting Indication (SS-MWI) 15 6.8.26 Priva

15、te User Mobility Incoming Call (ANF-PUMI) 16 6.8.27 Private User Mobility Outgoing Call (ANF-PUMO) 16 6.8.28 Common Information (ANF-CMN) 16 6.8.29 Call Priority Interruption (Protection) (SS-CPI(P) 16 6.8.30 Private User Mobility - Registration (SS-PUMR) 16 6.8.31 Single Step Call Transfer (SSCT) 1

16、6 6.8.32 Simple Dialog (SD) 16 6.9 ANF-CIDL parameter values (timers) 17 6.9.1 Timer T1 17 Annex A - Protocol Implementation Conformance Statement (PICS) proforma 19 Annex B - Examples of message sequences 31 Annex C - Specification and Description Language (SDL) representation of procedures 37 Anne

17、x D - Imported definitions 43 Annex E - ASN.1 definitions according to ITU-T Recs. X.208 / X.209 49 1 Scope This Standard specifies the signalling protocol for the support of the Call Identification and Call Linkage additional network feature (ANF-CIDL) at the Q reference point between Private Integ

18、rated Network services eXchanges (PINXs) connected together within a Private Integrated Services Network (PISN). ANF-CIDL is an additional network feature which allows the assignment of a Global Call Identification (GID) to identify a call end-to-end over the call route (i.e. between the two end PIN

19、Xs). As an option, a Thread Identification (TID) may be assigned to different calls which are logically linked together due to the operation of other supplementary services and/or ANFs. Additionally a Leg Identification (LID) may be assigned, to identify the different legs of a call. NOTE 1 This ANF

20、 has been developed to support the use of CSTA (ECMA-269) in a networked environment, i.e. in a PISN. Use of this ANF for other applications is not precluded. The Q reference point is defined in ECMA-133. Supplementary Service specifications are produced in three stages and according to the method s

21、pecified in ETS 300 387. This Standard contains the stage 3 specification for the Q reference point and satisfies the requirements identified by the stage 1 and stage 2 specifications in ECMA-313. The signalling protocol for ANF-CIDL operates on top of the signalling protocol for basic circuit switc

22、hed call control, as specified in ECMA-143, and uses certain aspects of the generic procedures for the control of supplementary services specified in ECMA-165. This Standard also specifies additional signalling protocol requirements for the support of interactions at the Q reference point between Ca

23、ll Identification and Call Linkage and other supplementary services and ANFs. This Standard is applicable to PINXs which can be interconnected to form a PISN. 2 Conformance In order to conform to this Standard, a PINX shall satisfy the requirements identified in the Protocol Implementation Conforman

24、ce Statement (PICS) proforma in annex A. Conformance to this Standard includes conforming to those clauses that specify protocol interactions between ANF-CIDL and other supplementary services and ANFs for which signalling protocols at the Q reference point are supported in accordance with the stage

25、3 standards concerned. 3 References (normative) The following standards contain provisions which, through reference in this text, constitute provisions of this Standard. All standards are subject to revision, and parties to agreements based on this Standard are encouraged to investigate the possibil

26、ity of applying the most recent editions of the standards indicated below. In the case of references to ECMA Standards that are aligned with ISO/IEC International Standards, the number of the appropriate ISO/IEC International Standard is given in brackets after the ECMA reference. ECMA-133 Private I

27、ntegrated Services Network (PISN) - Reference Configuration for PISN Exchanges (PINX) (International Standard ISO/IEC 11579-1) ECMA-142 Private Integrated Services Network (PISN) - Circuit Mode 64kbit/s Bearer Services -Service Description, Functional Capabilities and Information Flows (Internationa

28、l Standard ISO/IEC 11574) ECMA-143 Private Integrated Services Network (PISN) - Circuit Mode Bearer Services - Inter-Exchange Signalling Procedures and Protocol (International Standard ISO/IEC 11572) ECMA-155 Private Integrated Services Networks - Addressing (International Standard ISO/IEC 11571) -

29、2 - ECMA-165 Private Integrated Services Network (PISN) - Generic Functional Protocol for the Support of Supplementary Services - Inter-Exchange Signalling Procedures and Protocol (International Standard ISO/IEC 11582) ECMA-174 Private Integrated Services Network (PISN) - Inter-Exchange Signalling P

30、rotocol - Call Diversion Supplementary Services (International Standard ISO/IEC 13873) ECMA-176 Private Integrated Services Network (PISN) - Inter-Exchange Signalling Protocol - Path Replacement Additional Network Feature (International Standard ISO/IEC 13874) ECMA-178 Private Integrated Services Ne

31、twork (PISN) - Inter-Exchange Signalling Protocol - Call Transfer Supplementary Service (International Standard ISO/IEC 13869) ECMA-186 Private Integrated Services Network (PISN) - Inter-Exchange Signalling Protocol - Call Completion Supplementary Services (International Standard ISO/IEC 13870) ECMA

32、-192 Private Integrated Services Network (PISN) - Inter-Exchange Signalling Protocol - Call Offer Supplementary Service (International Standard ISO/IEC 14843) ECMA-194 Private Integrated Services Network (PISN) - Inter-Exchange Signalling Protocol - Do Not Disturb and Do Not Disturb Override Supplem

33、entary Services (International Standard ISO/IEC 14844) ECMA-203 Private Integrated Services Network (PISN) - Inter-Exchange Signalling Protocol - Call Intrusion Supplementary Service (International Standard ISO/IEC 14846) ECMA-221 Private Integrated Services Network (PISN) - Inter-Exchange Signallin

34、g Protocol - Call Interception Additional Network Feature (International Standard ISO/IEC 15054) ECMA-264 Private Integrated Services Network (PISN) - Inter-Exchange Signalling Protocol - Call Priority Interruption and Call Priority Interruption Protection Supplementary Services (International Stand

35、ard ISO/IEC 15992) ECMA-269 Services for Computer Supported Telecommunications Applications (CSTA) Phase III (International Standard ISO/IEC 18051) ECMA-282 Private Integrated Services Network (PISN) - Inter-Exchange Signalling Protocol - Private User Mobility (PUM) - Registration Supplementary Serv

36、ice (International Standard ISO/IEC 17876) ECMA-284 Private Integrated Services Network (PISN) - Inter-Exchange Signalling Protocol - Private User Mobility (PUM) - Call Handling Additional Network Features (International Standard ISO/IEC 17878) ECMA-300 Private Integrated Services Network (PISN) - I

37、nter-Exchange Signalling Protocol - Single Step Call Transfer Supplementary Service (International Standard ISO/IEC DIS 19460) ECMA-302 Private Integrated Services Network (PISN) - Inter-Exchange Signalling Protocol - Wireless Terminal Location Registration Supplementary Service and Wireless Termina

38、l Information Exchange Additional Network Feature (International Standard ISO/IEC 15429) ECMA-304 Private Integrated Services Network (PISN) - Inter-Exchange Signalling Protocol - Wireless Terminal Call Handling Additional Network Features (International Standard ISO/IEC 15431) ECMA-306 Private Inte

39、grated Services Network (PISN) - Inter-Exchange Signalling Protocol - Wireless Terminal Authentication Supplementary Services (International Standard ISO/IEC 15433) ECMA-313 Private Integrated Services Network (PISN) - Specification, Functional Model and Information Flows - Call Identification and C

40、all Linkage Additional Network Feature ETS 300 387 Private Telecommunication Network (PTN); Method for the specification of basic and supplementary services (1994) - 3 - ITU-T Rec. H.225 Call signalling protocols and media stream packetization for packet-based multimedia communication systems (1999)

41、 ITU-T Rec. I.112 Vocabulary of terms for ISDNs (1993) ITU-T Rec. I.210 Principles of telecommunication services supported by an ISDN and the means to describe them (1993) ITU-T Rec. Q.950 Supplementary services protocols, structure and general principles (2000) ITU-T Rec. Z.100 Specification and de

42、scription language (1999) 4 Definitions For the purposes of this Standard, the following definitions apply. 4.1 External definitions This Standard uses the following terms defined in other documents: Application Protocol Data Unit (APDU) (ECMA-165) ANF-CIDL user (ECMA-313) Basic Call (ECMA-143) Basi

43、c Service (ITU-T Rec. I.210) Call Identification Data, CIDL data (ECMA-313) Call Independent Signalling Connection (ECMA-165) Complete Number (ECMA-155) Gateway PINX (ECMA-143) Global Call Identification, Global Call ID, GID (ECMA-313) Global Thread Identification, Thread ID, TID (ECMA-313) Interpre

44、tation APDU (ECMA-165) Leg Identification (ECMA-313) Network Facility Extension (NFE) (ECMA-165) Originating PINX (ECMA-165) Private Integrated Services Network (PISN) (ECMA-133) Private Integrated services Network eXchange (PINX) (ECMA-133) Signalling (ITU-T Rec. I.112) Supplementary Service (ITU-T

45、 Rec. I.210) Supplementary Service Control Entity (ECMA-165) Terminating PINX (ECMA-165) Transit PINX (ECMA-165) User (ECMA-142) - 4 - 4.2 Other definitions 4.2.1 CIDL PINX The PINX receiving initial Global Call ID and optionally Thread ID and Leg ID values from the Originating PINX of a call. Upon

46、supplementary / ANF interactions (e.g. after call transfer), the CIDL PINX may generate a new Global Call ID for the resulting call and may correlate two or more logically linked calls together by updating the Thread ID values of these calls. NOTE 2 The CIDL PINX may be the Originating or the Termin

47、ating PINX of a call, as well as any other PINX invoking Supplementary Services / ANFs for this call, e.g. the SS-CT Transferring PINX. 4.2.2 CIDL Transit PINX A Transit PINX on the call route between the Originating PINX and a CIDL PINX or between two CIDL PINXs, which informs the local ANF-CIDL us

48、er about incoming CIDL Data and passes the data on unchanged to the subsequent PINX. 5 Acronyms ANF-CIDL Additional Network Feature Call Identification and Call Linkage APDU Application Protocol Data Unit ASN.1 Abstract Syntax Notation no. 1 CIDL Call Identification and Call Linkage GID Global Call

49、Identification ID Identification ISDN Integrated Services Digital Network LID Leg Identification NFE Network Facility Extension PICS Protocol Implementation Conformance Statement PINX Private Integrated services Network eXchange PISN Private Integrated Services Network PNP Private Numbering Plan SDL Specification and Description Language TID Thread Identification 6 Signalling protocol for the support of ANF-CIDL 6.1 ANF-CIDL description NOTE 3 If not otherwise stated, the term call is used in the sense of a Basic Call or a Call Independent Sig