DLA QQ-B-639B (1)-2002 BRASS NAVAL FLAT PRODUCTS (PLATE BAR SHEET AND STRIP).pdf

《DLA QQ-B-639B (1)-2002 BRASS NAVAL FLAT PRODUCTS (PLATE BAR SHEET AND STRIP).pdf》由会员分享，可在线阅读，更多相关《DLA QQ-B-639B (1)-2002 BRASS NAVAL FLAT PRODUCTS (PLATE BAR SHEET AND STRIP).pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、 INCH-POUND QQ-B-639B AMENDMENT 16 August 2002 FEDERAL SPECIFICATION BRASS, NAVAL: FLAT PRODUCTS (PLATE, BAR, SHEET, AND STRIP) The General Services Administration has authorized the use of this amendment, which forms a part of QQ-B-639B, dated 18 October 1973 by all federal agencies. PAGE 1 2.1: De

2、lete. PAGE 2 2.2: Delete and Substitute: “2.2 Non-Government publications. The following documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues of the documents which are DoD adopted are those listed in the issue of the D0DISS cited in the solic

3、itation. Unless otherwise specified, the issues of documents not listed in the D0DISS are the issues of the documents cited in the solicitation (see 6.2). AMERICAN SOCIETY FOR QUALITY CONTROL ASQC Z1.4 - Sampling Procedures and Tables for Inspection by Attributes (Application for copies should be ad

4、dressed to the American Society for Quality Control, P.O. Box 3005, 611 E. Wisconsin Avenue, Milwaukee, WI 53201-4606.) AMERICAN SOCIETY FOR TESTING AND MATERIALS ASTM B154 - Mercurous Nitrate Test for Copper and Copper Alloys ASTM E8 - Standard Test Methods for Tension Testing of Metallic Materials

5、 ASTM E1282 - Standard Guide for Specifying the Chemical Compositions and Selecting Sampling Practices and Quantitative Analysis Methods for Metals, Ores, and Related Materials (Application for copies should be addressed to the American Society for Testing and Material, 100 Barr Harbor Dr., West Con

6、shohocken, PA 19428.)” AMSC N/A 1 of 3 FSC 9530 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-QQ-B-639B AMENDMENT 1 SAE INTERNATIONAL (SAE) AMS-STD-185 - Identificati

7、on Marking of Copper and Copper Base Alloy Mill Products AMS2221 - Tolerances, Copper and Copper Alloy Bars and Rods AMS2222 - Tolerances, Copper and Copper Alloy Sheet, Strip, and Plate (Application for copies should be addressed to the SAE International, 400 Commonwealth Drive, Warrendale, PA 1509

8、6.)” PAGE 5 3.7: Delete and substitute: “3.7 Dimensional tolerances. Dimensional tolerances shall be in accordance with the applicable AMS2221 or AMS2222.” PAGE 6 3.8: Delete “Fed. Std. 185 No. 185” and substitute “AMS-STD-185”. PAGE 7 4.3.1, last line: Delete “method 111 or 112 of Fed. Test Method

9、Std No. 151” and substitute with “ASTM E1282”. 4.3.4.2, first sentence: Delete “MIL-STD-105, inspection level II, with an acceptable quality level (AQL) of 1.5 percent defective.”and substitute “ASQC Z1.4. Lot acceptance criteria shall be based on a single sampling plan with a zero acceptance number

10、.” PAGE 8 4.6.1, second line: Delete “by the wet chemical method” and “method 111 of Fed. Test Method Std. No. 151 or the spectrochemical method in accordance with method 112 of Fed. Test Method Std. No. 151” and substitute with “ ASTM E1282”. 4.6.1, last sentence: Delete. PAGE 9 4.7, 4.7.1 & 4.7.2:

11、 Delete 5: Delete Section 5 entirely and substitute: “5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When actual packaging of material is to be performed by DoD personnel, these personnel need to contact the

12、responsible packaging activity to ascertain requisite packaging requirements. Packaging requirements are maintained by the Inventory Control Points packaging activity within the Military Department or Defense Agency, or within the Military Departments System Command. Packaging data retrieval is avai

13、lable from the managing Military Departments or Defense Agencys automated packaging files, CD-ROM products, or by contacting the responsible packaging activity.” PAGE 10 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-QQ-B-639B AMENDMENT 1 6.2m & 6

14、.2n: Delete. 6.3: Delete. Page 12 6.6: Delete second sentence and substitute with “For specifications cover naval brass rod, bar, shapes and forgings, see ASTM B21, ASTM B124 and ASTM B283”. Custodians: Preparing Activity: Army - MR DLA - IS Navy - SH Air Force -99 (Project 9530-0565) Review Activities: Army AT, MI Navy AS, MC, OS, YD Air Force 84 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-