DLA MS27479 REV G-2012 CONNECTOR RECEPTACLE ELECTRICAL WALL MOUNTING FLANGE CRIMP TYPE BAYONET COUPLING SERIES II [Use DLA MS27472 REV J DLA MS27472 REV H NOTICE 1 DLA MS27472 REV .pdf

《DLA MS27479 REV G-2012 CONNECTOR RECEPTACLE ELECTRICAL WALL MOUNTING FLANGE CRIMP TYPE BAYONET COUPLING SERIES II [Use DLA MS27472 REV J DLA MS27472 REV H NOTICE 1 DLA MS27472 REV .pdf》由会员分享，可在线阅读，更多相关《DLA MS27479 REV G-2012 CONNECTOR RECEPTACLE ELECTRICAL WALL MOUNTING FLANGE CRIMP TYPE BAYONET COUPLING SERIES II [Use DLA MS27472 REV J DLA MS27472 REV H NOTICE 1 DLA MS27472 REV .pdf（7页珍藏版）》请在麦多课文档分享上搜索。

1、 DETAIL SPECIFICATION SHEET CONNECTOR, RECEPTACLE, ELECTRICAL, WALL MOUNTING FLANGE, CRIMP TYPE, BAYONET COUPLING, SERIES II This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist

2、of this specification sheet and MIL-DTL-38999. FIGURE 1. Receptacle, classes E and T. AMSC N/A FSC 5935 MS27479G 27 June 2012 SUPERSEDING MS27479F 12 July 2002 INCH-POUND Inactive for new design after 27 June 2012. For new design, use MS27472. Provided by IHSNot for ResaleNo reproduction or networki

3、ng permitted without license from IHS-,-,-MS27479G 2 FIGURE 1. Receptacle, classes E and T Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27479G 3 Shell size A dia +.001 -.005 B dia +.000 -.016 over projection C dia +.006 -.002 D dia +.

4、005 -.001 I dia .005 N dia +.005 -.006 8 .473 .563 .078 .362 .285 .412 10 .590 .680 .490 .413 .540 12 .750 .859 .607 .527 .689 14 .875 .984 .732 .652 .814 16 1.000 1.103 .857 .777 .939 18 1.125 1.233 .962 .866 1.039 20 1.250 1.358 .125 1.087 .991 1.164 22 1.375 1.483 1.212 1.116 1.289 24 1.500 1.610

5、 1.337 1.241 1.414 Shell size Q max R BSC S max T +.010 -.005 CC For insert arrangement, see MS drawing 8 1.078 .297 .828 .120 .004 27343, 27516 10 1.266 .3595 .954 .010 27344, 27517 12 1.391 .406 1.047 27345, 27518 14 1.516 .453 1.141 27346, 27519 16 1.641 .4845 1.234 27347, 27520 18 1.766 .531 1.3

6、28 27348, 27521 20 1.891 .578 1.453 27349, 27522 22 2.016 .625 1.578 27350, 27523 24 2.204 .6875 1.703 .147 27351, 27524 FIGURE 1. Receptacle, classes E and T Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27479G 4 NOTES: 1. Insert fron

7、t surface shall be flat within .005 T.I.R. 2. Dimensions are in inches. 3. The point at which a gage pin, having the same basic diameter as the mating contact and a square face, touches socket contact spring. 4. Normal keyway position. For other keyway positions see MIL-DTL-38999. 5. Diameters A and

8、 D shall be concentric within .015 T.I.R. 6. Diameter A with respect to diameter B, and diameter D with respect to diameter N, shall be concentric at MMC. 7. Diameters D and I shall be concentric within .015 T.I.R at MMC. 8. The gauge features for GG shall be CC smaller than their MMC size at basic

9、location. 9. The gauge features for GG shall be .010 smaller than their MMC size at basic location. FIGURE 1. Receptacle, classes E and T Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27479G 5 Shell size G insert projection (class T on

10、ly) HH dia +.000 -.005 KK dia (datum) NN PP dia .003 8 .120 .030 .387 .366 12 .344 10 .515 .487 16 .472 12 .628 .609 20 .586 14 .754 .731 24 .711 16 .879 .853 28 .836 18 .985 .974 32 .942 20 1.110 1.097 36 1.067 22 1.235 1.218 40 1.192 24 .0900 .050 1.360 1.340 44 1.317 Shell size LE max overall len

11、gth LT max overall length XE max dia VV Thread UNEF-2A MOD (plated) Size Major dia MOD 8 .562 .391 .594 7/16 28 .421 .417 10 .719 9/16 24 .542 .538 12 .844 11/16 24 .667 .663 14 .969 13/16 20 .791 .787 16 1.094 15/16 20 .916 .912 18 1.219 1 1/16 18 1.034 1.030 20 1.344 1 3/16 18 1.158 1.154 22 1.469

12、 1 5/16 18 1.283 1.279 24 .469 1.594 1 7/16 18 1.408 1.404 FIGURE 1. Receptacle, classes E and T Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27479G 6 REQUIREMENTS: Dimensions and configuration: See figure 1. Interface dimensions shal

13、l conform to MIL-DTL-38999. This receptacle mates with MS27473, MS27480, MS27484 and MS27500. Insert arrangements: See MIL-STD-1560. Part or Identifying Number (PIN) example: MS27479 T 24 C 61 P A MS number Class Shell size Finish Insert arrangement Contact style Polarizing positions No letter is re

14、quired for normal. Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue, due to the extent of the changes. Referenced documents. In addition to MIL-DTL-38999, this document references the following: MIL-STD-1560 MS27472

15、MS27473 MS27480 MS27484 MS27500 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27479G 7 CONCLUDING MATERIAL Custodians: Preparing activity: Army CR DLA CC Navy AS Air Force 85 (Project 5935-2012-029) DLA CC Review activities: Army AR, MI Navy EC,

16、MC, OS Air Force 19, 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-