DLA MS9095 REV B-2010 NIPPLE TUBE - ALUMINUM BOSS.pdf

《DLA MS9095 REV B-2010 NIPPLE TUBE - ALUMINUM BOSS.pdf》由会员分享，可在线阅读，更多相关《DLA MS9095 REV B-2010 NIPPLE TUBE - ALUMINUM BOSS.pdf（7页珍藏版）》请在麦多课文档分享上搜索。

1、 MS9095B 16 February 2010 SUPERSEDING MS9095A 11 March 1970 DETAIL SPECIFICATION SHEET NIPPLE, TUBE - ALUMINUM, BOSS This specification is approved for use by all Departments and Agencies of the Department of Defense . The requirements for acquiring the product described herein shall consist of this

2、 specification sheet and SAE-AS4841. Inches mm .020 0.51 FIGURE 1. Nipple, tube, boss. AMSC N/A FSC 4730 INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS9095B 2 Inches mm .005 .020 0.13 0.51 FIGURE 1. Nipple, tube, boss - Continued. Prov

3、ided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS9095B 3 Dash number Tube OD inches (mm) Thread T (see note 10) A diameter inches (mm) B inches (mm) +.015 (0.38) -.000 -08 .500 (12.70) .7500 - 16UNF - 3A .387 (9.83) - .395 (10.03) .229 (5.82) -09 .562 (

4、14.27) .8125 - 16UN - 3A .434 (11.02) - .442 (11.23) .229 (5.82) -10 .625 (15.88) .8750 - 14UNF - 3A .480 (12.19) - .488 (12.40) .255 (6.48) -11 .688 (17.48) 1.000 - 12UNF - 3A .542 (13.77) - .552 (14.02) .304 (7.72) -12 .750 (19.05) 1.0625 - 12UN - 3A .604 (15.34) - .614 (15.60) .304 (7.72) -14 .87

5、5 (22.23) 1.1875 - 12UN - 3A .729 (18.52) - .739 (18.77) .304 (7.72) -16 1.000 (25.40) 1.3125 - 12UN - 3A .839 (21.31) - .851 (21.62) .312 (7.92) -18 1.125 (28.58) 1.500 - 12UNF - 3A .948 (24.08) - .960 (24.38) .312 (7.92) -20 1.250 (31.75) 1.625- 12UN - 3A 1.073 (27.25) - 1.086 (27.58) .363 (9.22)

6、-24 1.500 (38.10) 1.8750 - 12UN - 3A 1.307 (33.20) - 1.320 (33.53) .374 (9.50) -28 1.750 (44.45) 2.2500 - 12UN - 3A 1.542 (39.17) - 1.557 (39.55) .447 (11.35) -32 2.000 (50.80) 2.500 - 12UN - 3A 1.776 (45.11) - 1.791 (45.49) .457 (11.61) Dash number C diameter +.000 -.010 (0.25) inches (mm) D diamet

7、er .003 (0.08) inches (mm) E +.015 (0.38) -.000 inches (mm) F diameter +.002 (0.05) -.003 (0.08) inches (mm) (see notes 5 and 6) G min inches (mm) -08 .660 (16.76) .462 (11.73) .094 (2.39) .660 (16.76) 1.130 (28.70) -09 .722 (18.34) .509 (12.93) .094 (2.39) .722 (18.34) 1.200 (30.48) -10 .773 (19.63

8、) .555 (14.10) .107 (2.72) .773 (19.63) 1.270 (32.26) -11 .882 (22.40) .619 (15.72) .125 (3.18) .882 (22.40) 1.484 (37.69) -12 .945 (24.00) .681 (17.30) .125 (3.18) .945 (24.00) 1.556 (39.52) -14 1.070 (27.18) .806 (20.47) .125 (3.18) 1.070 (27.18) 1.699 (43.15) -16 1.195 (30.35) .918 (23.32) .125 (

9、3.18) 1.195 (30.35) 1.842 (46.79) -18 1.382 (35.10) 1.027 (26.09) .125 (3.18) 1.382 (35.10) 1.983 (50.37) -20 1.507 (38.28) 1.153 (29.29) .125 (3.18) 1.507 (38.28) 2.126 (54.00) -24 1.756 (44.60) 1.387 (35.23) .125 (3.18) 1.756 (44.60) 2.411 (61.24) -28 2.131 (54.13) 1.652 (41.96) .125 (3.18) 2.131

10、(54.13) 2.839 (72.11) -32 2.381 (60.48) 1.886 (47.90) .125 (3.18) 2.381 (60.48) 3.124 (79.35) FIGURE 1. Nipple, tube, boss - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS9095B 4 Dash number H inches (mm) J inches (mm) K inches (mm) L

11、inches (mm) -08 .990 (25.15) - 1.002 (25.45) .633 (16.08) .440 (11.18) .883 (22.43) -09 1.052 (26.72) - 1.064 (27.03) .633 (16.08) .440 (11.18) .883 (22.43) -10 1.114 (28.30) - 1.127 (28.63) .747 (18.97) .440 (11.18) 1.057 (26.85) -11 1.301 (33.05) - 1.314 (33.38) .853 (21.67) .440 (11.18) 1.163 (29

12、.54) -12 1.364 (34.65) - 1.377 (34.98) .853 (21.67) .480 (12.19) 1.163 (29.54) -14 1.489 (37.82) - 1.502 (38.15) .898 (22.81) .480 (12.19) 1.208 (30.68) -16 1.614 (41.00) - 1.627 (41.33) .908 (23.06) .480 (12.19) 1.268 (32.21) -18 1.738 (44.15) - 1.752 (44.50) .954 (24.23) .480 (12.19) 1.314 (33.38)

13、 -20 1.863 (47.32) - 1.877 (47.68) .954 (24.23) .480 (12.19) 1.314 (33.38) -24 2.113 (53.67) - 2.127 (54.03) 1.079 (27.41) .480 (12.19) 1.439 (36.55) -28 2.488 (63.20) - 2.502 (63.55) 1.204 (30.58) .480 (12.19) 1.594 (40.49) -32 2.738 (69.55) - 2.752 (69.90) 1.329 (33.76) .480 (12.19) 1.719 (43.66)

14、Dash number M min inches (mm) P inches (mm) R diameter inches (mm) Approx weight lbs/ea grams/ea -08 .030 (0.76) .040 (1.02) - .070 (1.78) 1.000 (25.40) .044 (20) -09 .030 (0.76) .040 (1.02) - .070 (1.78) 1.062 (26.97) .050 (23) -10 .030 (0.76) .050 (1.27) - .080 (2.03) 1.125 (28.58) .065 (29) -11 .

15、030 (0.76) .050 (1.27) - .080 (2.03) 1.312 (33.32) .091 (41) -12 .030 (0.76) .050 (1.27) - .080 (2.03) 1.375 (34.93) .100 (45) -14 .030 (0.76) .050 (1.27) - .080 (2.03) 1.500 (38.10) .117 (53) -16 .030 (0.76) .050 (1.27) - .080 (2.03) 1.625 (41.28) .144 (65) -18 .030 (0.76) .050 (1.27) - .080 (2.03)

16、 1.750 (44.45) .185 (84) -20 .030 (0.76) .050 (1.27) - .080 (2.03) 1.875 (47.63) .203 (92) -24 .030 (0.76) .050 (1.27) - .080 (2.03) 2.125 (53.98) .262 (119) -28 .044 (1.12) .050 (1.27) - .080 (2.03) 2.500 (63.50) .416 (189) -32 .044 (1.12) .050 (1.27) - .080 (2.03) 2.700 (68.58) .508 (230) FIGURE 1

17、. Nipple, tube, boss - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS9095B 5 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Unless otherwise specified machined tolerances linear dimensions

18、.010 inch (0.25 mm) angular dimensions 5. 4. Surface texture unless otherwise specified shall be 125 inches (3.17m) except hex, as specified in ASME B46.1. 5. Diameter F shall be free of thread marks. 6. Diameter F shall be concentric with pitch diameter of thread within .0025 inch (0.064 mm) FIM. 7

19、. Lettering height: a. For sizes -08 through -16: 040 - .060 inch (1.02 - 1.52 mm). b. For sizes -18 and larger: .090 - .150 inch (2.29 - 3.81 mm). 8. All diameters shall be concentric within .010 inch (0.25 mm) FIM unless otherwise specified. 9. Unless otherwise specified break sharp edges .003 - .

20、015 inches (0.08 - 0.38 mm). 10. Threads shall be in accordance with FED-STD-H28/2. FIGURE 1. Nipple, tube, boss - Continued. REQUIREMENTS: Dimensions and configurations: See figure 1. Max pressure: 1500 psi (10 MPa). Operating temperature: -40F to 200F (-40C to 93C). Material: Aluminum as specified

21、 in table I. TABLE I. Materials. Material Form Designator Specification Alloy Aluminum alloy Bar Blank SAE-AMS4121 AMS4121 W1 SAE-AMS-QQ-A-225/9 7075-T73 W2 SAE-AMS4124 or SAE-AMS-QQ-A-225/9 7075-T7351 Forgings W3 SAE-AMS4127 6061-T6 W4 SAE-AMS-A-22771 7075-T6, T62, or T651 W5 SAE-AMS-A-22771, SAE-A

22、MS-QQ-A-367, or SAE-AMS4141 7075-T73 W6 Finish: Anodize treatment in accordance with SAE-AMS2470 for SAE-AMS4121 and for W alloys anodizing shall be in accordance with MIL-A-8625, type II, class 2. All parts shall be fluorescent penetrant inspected in accordance with ASTM E1417. Provided by IHSNot f

23、or ResaleNo reproduction or networking permitted without license from IHS-,-,-MS9095B 6 PIN: MS9095 -08 W PIN Example: MS9095-08 identifies a nipple, tube, boss .500 inch (12.70 mm) tube, aluminum alloy AMS4121. Do not use unassigned PINs. Intended usage: Jet engine, miscellaneous parts, oil, fuel,

24、and de-icing kits. Not to be used on hydraulic, oxygen or applications requiring pressures of 3000 psi (21 MPa). Supersession data. Aluminum alloy designator W replaces SAE-AMS4121 (blank designator); however SAE-AMS4121 aluminum alloy (blank designator) does not replace the “W” alloys. Changes from

25、 previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Referenced documents. In addition to SAE-AS4841, this document references the following: FED-STD-H28/2 MIL-A-8625 ASME B46.1 ASTM E1417 SAE-AMS24

26、70 SAE-AMS2800 SAE-AMS4121 SAE-AMS4124 SAE-AMS4127 SAE-AMS4141 SAE-AMS-A-22771 SAE-AMS-QQ-A-225/9 SAE-AMS-QQ-A-367 Specification sheet number Nipple tube coupling size (see figure 1) Aluminum type blank or W (see table I). Provided by IHSNot for ResaleNo reproduction or networking permitted without

27、license from IHS-,-,-MS9095B 7 CONCLUDING MATERIAL Custodians: Preparing activity: Army - AV DLA - CC Navy - AS Air Force - 99 (Project 4730-2009-078) DLA CC Review activities: Navy - MC Air Force - 71, 85 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-