DLA MIL-PRF-8805 93 E-2010 SWITCHES TOGGLE UNSEALED 7 0 AMPERES.pdf

《DLA MIL-PRF-8805 93 E-2010 SWITCHES TOGGLE UNSEALED 7 0 AMPERES.pdf》由会员分享，可在线阅读，更多相关《DLA MIL-PRF-8805 93 E-2010 SWITCHES TOGGLE UNSEALED 7 0 AMPERES.pdf（9页珍藏版）》请在麦多课文档分享上搜索。

1、 AMSC N/A FSC 5930 INCH-POUND MIL-PRF-8805/93E 11 May 2010 SUPERSEDING MIL-PRF-8805/93D 31 October 2001 PERFORMANCE SPECIFICATION SHEET SWITCHES, TOGGLE, UNSEALED, 7.0 AMPERES This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for ac

2、quiring the switches described herein shall consist of this specification sheet and MIL-PRF-8805. FIGURE 1. Configurations and dimensions. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-8805/93E 2 Inches mm Inches mm Inches mm Inches mm .002

3、 0.05 .110 2.79 .468 11.89 .930 23.62 .003 0.08 .13 3.30 .469 11.91 1.15 29.21 .005 0.13 .240 6.10 .50 12.70 1.16 29.46 .015 0.38 .388 9.86 .56 14.22 1.17 29.72 .03 0.76 .432 10.97 .670 17.02 1.30 33.02 .032 0.81 .448 11.38 .720 18.29 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are giv

4、en for general information only. 3. Unless otherwise specified, tolerances are .03 inch (0.76 mm) for two place decimals and .005 inch (0.13 mm) for three place decimals. 4. Configuration optional provided that specified envelope dimensions are not exceeded. 5. Alternative base metals and protective

5、 finishes, as approved by the qualifying activity, may be utilized for hexagon nut, lock washer and key washer material. Dimensions shall be in accordance with the referenced hardware specifications. FIGURE 1. Configurations and dimensions - continued. NASM35333-136 LOCKWASHER OR EQUIVALENT SEE NOTE

6、 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-8805/93E 3 FIGURE 2. Schematic diagram. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-8805/93E 4 FIGURE 2. Schematic diagram - cont

7、inued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-8805/93E 5 REQUIREMENTS: Dimensions and configuration: See figure 1. Basic switch shall be MS24547-4 (MIL-PRF-8805/4). Enclosure design: 1 (Unsealed). Use boot in accordance with MIL-DTL-

8、5423/2 (PIN M5423/02-01) for panel seal. Temperature characteristic: 1 (-40C to +85C). Shock (specified pulse): MIL-STD-202, method 213, test condition C, (100 g, half sine). Sinusoidal vibration grade: 1 (10 to 500 Hz, 10 g peak). Weight: Type I: 0.78 pound maximum. Type II and III: 0.93 pound maxi

9、mum. Type IV: 0.125 pound maximum. Terminal strength: 5 pounds. Contact resistance: Initial 50 milliohms, 100 milliohms after mechanical endurance. Operating characteristics: Coincidence of operating and release points: All poles shall transfer within 5.of lever travel. Operating force: 6 pounds max

10、imum. Material: Lever and bracket: Corrosion resistant steel or equivalent. Dielectric withstanding voltage: Altitude: 50,000 feet (MIL-STD-202, method 105, test condition B). Mechanical endurance: 50,000 cycles at a cycling rate of 15 to 65 cycles per minute. Electrical endurance: 25,000 cycles. El

11、ectrical ratings: See table I. Part or Identifying Number (PIN): See table II Qualification: Group submission: See table III. Group B inspection: Subject one M8805/93-002 or 003, and one 027 or 028 to each of the test groups specified in table IV. Provided by IHSNot for ResaleNo reproduction or netw

12、orking permitted without license from IHS-,-,-MIL-PRF-8805/93E 6 TABLE I. Electrical ratings. Load Sea level 50,000 feet 28 V dc 115 V ac, 60 Hz 28 V dc Resistive Inductive Lamp amperes 7.0 4.0 2.5 amperes 7.0 7.0 2.0 amperes 4.0 2.5 2.5 TABLE II. PINs and characteristics. PIN M8805/93 Type (see fig

13、ure 2) Circuit Toggle lever operation in “D” flat side center side opposite “D” flat -001 -002 -003 -004 -005 -006 -007 I I I I I I I 2PDT 2PDT 2PDT 2PDT 2PDT 2PDT 2PDT Maintained maintained maintained Momentary maintained maintained Maintained maintained momentary Momentary maintained momentary Mai

14、ntained none maintained Momentary none maintained Maintained none momentary -008 -009 -010 -011 -012 -013 -014 II II II II II II II 4PDT 4PDT 4PDT 4PDT 4PDT 4PDT 4PDT Maintained maintained maintained Momentary maintained maintained Maintained maintained momentary Momentary maintained momentary Maint

15、ained none maintained Momentary none maintained Maintained none momentary -015 -016 -017 -018 -019 -020 -021 III III III III III III III 6PDT 6PDT 6PDT 6PDT 6PDT 6PDT 6PDT Maintained maintained maintained Momentary maintained maintained Maintained maintained momentary Momentary maintained momentary

16、Maintained none maintained Momentary none maintained Maintained none momentary -022 -023 -024 -025 -026 -027 -028 IV IV IV IV IV IV IV 8PDT 8PDT 8PDT 8PDT 8PDT 8PDT 8PDT Maintained maintained maintained Momentary maintained maintained Maintained maintained momentary Momentary maintained momentary Ma

17、intained none maintained Momentary none maintained Maintained none momentary Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-8805/93E 7 TABLE III. Qualification inspection. Examination or test Test sample Extent of approval Group I (14 sample

18、 units). Visual and mechanical examination Operating characteristics All sample units for groups II through V, plus I each of any type II unit and any type III unit All PINs Group II (4 sample units). Strength of actuating means Strength of mounting bushing Thermal shock Vibration Shock (specified p

19、ulse) Operating characteristics Dielectric withstanding voltage Visual and mechanical examination Marking visibility 2 sample units of each of the following: M8805/93-002 or 003 and M8805/93-027 or 028 Group III (2 sample units). Salt spray (corrosion) Visual and mechanical examination Marking visib

20、ility 1 sample unit of each of the following: M8805/93-002 or 003 and M8805/93-027 or 028 Group IV (4 sample units). Contact resistance Low temperature operation 1/ Mechanical endurance at low temperature 2/ Mechanical endurance at high temperature 1/ Contact resistance Operating characteristics Die

21、lectric withstanding voltage Visual and mechanical examination 2 sample units of each of the following: M8805/93-002 or 003 and M8805/93-027 or 028 Group V (2 sample units). Electrical endurance Sea level Inductive load, dc Operating characteristics 1 sample unit of each of the following: M8805/93-0

22、02 or 003 and M8805/93-027 or 028 1/ Test one M8805/93-002 or 003, and one M8805/93-027 or 028 2/ Same sample units as for low temperature operation. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-8805/93E 8 TABLE IV. Group B inspection. Exa

23、mination or test Group I Strength of mounting bushing Thermal shock Shock Operating characteristics Marking visibility Group II Salt spray Marking visibility Group III Low temperature operation Mechanical endurance at low temperature Contact resistance Operating characteristics Group IV Mechanical e

24、ndurance at high temperature Contact resistance Operating characteristics Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-8805/93E 9 Reference documents: MIL-PRF-8805 MIL-PRF-8805/4 MIL-DTL-5423/2 MIL-STD-202 The margins of this specification

25、 are marked with vertical lines to indicate where modifications from this revision were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this doc

26、ument based on the entire content irrespective of the marginal notations. Custodians: Preparing activity: Army - CR DLA - CC Navy - EC Air Force - 85 (Project 5930-2008-050) DLA - CC Review activities: Army AR, AV Navy AS, MC Air Force 19 NOTE: The activities listed above were interested in this doc

27、ument as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil/ . Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-