DLA MIL-PRF-15160 60 J-2008 FUSES INSTRUMENT POWER AND TELEPHONE (NONINDICATING) STYLE F60.pdf

《DLA MIL-PRF-15160 60 J-2008 FUSES INSTRUMENT POWER AND TELEPHONE (NONINDICATING) STYLE F60.pdf》由会员分享，可在线阅读，更多相关《DLA MIL-PRF-15160 60 J-2008 FUSES INSTRUMENT POWER AND TELEPHONE (NONINDICATING) STYLE F60.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、AMSC N/A FSC 5920 INCH-POUND MIL-PRF-15160/60J 15 October 2008 SUPERSEDING MIL-PRF-15160/60H 14 March 2005 PERFORMANCE SPECIFICATION SHEET FUSES, INSTRUMENT, POWER, AND TELEPHONE (NONINDICATING), STYLE F60 This specification is approved for use by all Departments and Agencies of the Department of De

2、fense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-PRF-15160. NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. FIGURE 1. Style F60, characteristic C. Inches mm .004 0.10 .009 0.23 .031

3、0.79 .406 10.31 1.500 38.10 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-15160/60J 2 REQUIREMENTS: Interface and physical dimensions: See figure 1. Case: Glass melamine. Ferrule: Brass, copper, bronze, or copper alloy. Finish: Nickel, or s

4、ilver plated when specified. Terminal strength: Method 211 of MIL-STD-202, test condition E, 2 pound-inch torque between ferrules and fuse body. Electrical: Current rating: See table I. Current carrying capacity: 110 percent of rated current. Voltage rating: See table I. Characteristic: See table I.

5、 Overload interrupt: Within 1 hour at 135 percent of rated current; and within 2 minutes at 200 percent. Short circuit interrupt: 200,000 A at 500 V ac (symmetrical), 150,000 A at 500 V dc. Shock: Method 207 of MIL-STD-202, HI shock. Vibration: Method 204 of MIL-STD-202, test condition A (except 5g,

6、 500 Hz). Type designation: Type designation shall be as specified in table I. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-15160/60J 3 TABLE I. Type designation. 1/ 1/ For silver plated terminals, the designator “S“ is added after the cur

7、rent rating. VERIFICATION: Qualification inspections: The number of qualification samples required shall be: a. 24 samples maximum current rating of each voltage and design. b. 24 samples minimum current rating of each voltage and design. NOTE: If labels are used, five additional samples of any rati

8、ng are required. Sample size: The number of group III samples shall be twelve samples each of the maximum and minimum current ratings. The samples shall be divided as shown in table II. TABLE II. Short circuit test. 1/ A 600 volt ac test voltage may be used. Group C inspection: Group C inspection sh

9、all be performed on short circuit current ratings of 5,000 A at 500 V ac; 200,000 A at 500 V ac; and 5,000 A at 500 V dc. The 150,000 A at 500 V dc short circuit current test is not required to be performed for group C testing. Style Characteristic Voltage Current F60 F60 F60 F60 F60 F60 F60 F60 F60

10、 F60 F60 F60 F60 F60 F60 F60 F60 F60 F60 F60 C C C C C C C C C C C C C C C C C C C C 500V 500V 500V 500V 500V 500V 500V 500V 500V 500V 500V 500V 500V 500V 500V 500V 500V 500V 500V 500V 1/8A 2/10A 1/4A 3/10A 3/8A 1/2A 3/4A 1A 1 1/2A 2A 3A 4A 5A 6A 8A 10A 15A 20A 25A 30A Number of samples Short circui

11、t current Test voltage 3 3 3 3 5,000 A 200,000 A 5,000 A 150,000 A 500 V ac 1/ 500 V ac 1/ 500 V dc 500 V dc Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-15160/60J 4 INSPECTION ROUTINE: AC short circuit test: AC short circuit tests shall b

12、e performed at the currents shown in table II at not less than 500 volts, single phase, and not greater than 20 percent power factor, lagging. The current shall be applied within plus or minus 10 degrees of the zero point of the voltage wave. DC short circuit test: DC short circuit tests shall be pe

13、rformed at the currents shown in table II at not less than 500 volts. The rate of rise shall be between 25,000,000 and 30,000,000 amperes per second. Cross-reference: For applicable cross-reference see table III. The existing stocks of superseded items may be used. When exhausted, the superseding pa

14、rts shall be used. TABLE III. Cross-reference. Referenced documents. In addition to MIL-PRF-15160, this document references the following: MIL-STD-202 The margins of this specification sheet are marked with vertical lines to indicate where changes from the previous issue were made. This was done as

15、a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous

16、issue. Superseding Superseded numbers for CAGE number 81349 96906 F60C500V1/8A F60C500V1/4A F60C500V3/8A F60C500V1/2A F60C500V3/4A F60C500V1A F60C500V3A F60C500V5A F60C500V6A F60C500V8A F60C500V10A F60C500V15A F60C500V20A F60C500V25A F60C500V30A - - - - - F60H1R00C F60H3R00C F60H5R00C F60H6R00C F60H

17、8R00C F60H10R0C F60H15R0C F60H20R0C F60H25R0C F60H30R0C - - - - - MS15249-1 MS15249-3 MS15249-5 MS15249-6 MS15249-8 MS15249-10 MS15249-15 MS15249-20 MS15249-25 MS15249-30 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-15160/60J 5 Custodians:

18、 Preparing activity: Army - CR DLA - CC Navy - SH Air Force - 85 (Project 5920-2008-042) Review activities: Army - CR4, MI Navy - AS, CG, MC, OS, YD Air Force - 19, 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-