DLA MIL-PRF-1 1072 H-2009 ELECTRON TUBE CATHODE RAY TYPES 22CP7A AND 22CP25A.pdf

《DLA MIL-PRF-1 1072 H-2009 ELECTRON TUBE CATHODE RAY TYPES 22CP7A AND 22CP25A.pdf》由会员分享，可在线阅读，更多相关《DLA MIL-PRF-1 1072 H-2009 ELECTRON TUBE CATHODE RAY TYPES 22CP7A AND 22CP25A.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、 MIL-PRF-1/1072H 14 July 2009 _ SUPERSEDING MIL-E-1/1072G(NAVY) 25 June 1999 PERFORMANCE SPECIFICATION SHEET ELECTRON TUBE, CATHODE RAY TYPES 22CP7A AND 22CP25A This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the ele

2、ctron tube described herein shall consist of this document and the latest issue of MIL-PRF-1. DESCRIPTION: Magnetic deflection and focus, aluminized. DIMENSIONS AND PIN CONNECTIONS: See figure 1. ABSOLUTE RATINGS: Parameter: Unit: Ef V Ec1 V dc Ec2 V dc Eb V dc Ehk V dc Rg1 Meg Alt ft Maximum: Minim

3、um: 6.9 5.7 0 -125 450 - 18,000 - -125 - 1/ - 10,000 - Test condition: 6.3 Adjust 300 15,000 - - - See footnotes at end of table I. GENERAL: Qualification - Required. 1/ AMSC N/A FSC 5960 INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL

4、-PRF-1/1072H 2 TABLE I. Testing and inspection. Limits Inspection Method MIL-STD-1311 Notes Conditions Symbol Min Max Unit Qualification inspection Electrode current (grid No. 2) 5201 - Ec1 = 0 Ic2 - 15 A dc Modulation 5223 - Ib = 200 A dc Ec1 - 35 V dc Cathode illumination 5216 - - - - - Direct-int

5、erelectrode capacitance 1331 - Cathode to all Control grid to all Grid No. 2 to all Ck Cg1 Cg2 - - - 8 10 10 pF pF pF Pressure (implosion) 1141 - 35 Ib/psi - - - - Vibration 5111 - Width - 2.5 mm Base material insulating quality 1216 - - - - - Conformation inspection, part 1 Radius of faceplate - -

6、- 140 - Inches Voltage breakdown 5201 - - - - - Voltage breakdown (magnetic types) 5201 - - - - - Gas ratio 5206 - Gr - 0.25 - Neck and bulb alignment (magnetic types) 5101 7/ - - 0.400 Inch Face tilt 5101 8/ - - 0.375 Inch Neck straightness 5101 - - - - - Bulb, screen, and faceplate quality 5106 6/

7、 - - - - Spot position (magnetic deflection) 5231 - - - 25 mm Zero-bias anode current (magnetic deflection) 5236 4/ - - - - Grid cutoff voltage 5241 - Ec1 -33 -77 V dc Grid No. 1 leakage current 5251 - - - - - See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking

8、permitted without license from IHS-,-,-MIL-PRF-1/1072H 3 TABLE I. Testing and inspection - Continued. Limits Inspection Method MIL-STD-1311 Notes Conditions Symbol Min Max Unit Conformance inspection, part 2 Heater current 1301 - If 540 660 mA Stray light emission (conventional types) 5216 - Eb = 18

9、,000 V dc; Ec2 = 450 V dc - - - - Screen (P7) 5221 2/ - - - - Screen (P25) - 5/ cBf D0.1(10) D1(10) D1(10)- D10(10) 600 400 325 50 - - - 80 cB cB cB cB Line width A 5226 3/ Ib = 200 A dc Width - 1.25 mm Line width C 5226 3/ Ib = 200 A dc Width - 2.0 mm Focusing ampere turns 5246 - Ib = 200 A dc; D =

10、 3.25 AT 600 720 - Heater-cathode leakage current 5251 - - - - - Grid No. 2 leakage current 5251 - - - - - Base pin solder depth 1111 - - - - - Secureness of base, cap, or insert 1101 - - - - - Permanence of marking 1105 - - - - - Conformance inspection, part 3 Life test - - Group C; Eb = 14,000 V d

11、c; Ec2 = 450 V dc; Ib = 200 A dc t 500 - hours Life-test end points: Line width A Line width C Modulation - 5226 5226 5223 - - - Ib = 200 A dc Ib = 200 A dc Ib = 200 A dc Width Width Ec1 - - - 1.35 2.2 39 mm mm V dc 1/ When Ec2 is greater than 330 V dc, Rg1 shall not exceed 0.5 Meg. When Ec2 is less

12、 than 330 V dc, Rg1 shall not exceed 1.5 Meg. 2/ The screen characteristics shall be measured with constant beam energy of 0.24 watt defocused to a spot approximately 0.25 cm (0.1 in) in diameter. The test conditions shall be anode voltage (relative to cathode) 4,000 V minimum and beam current 60 A

13、maximum. The screen characteristics shall comply with the following minimum limits: cB5 = 400 cB; G5:1 = 4. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-1/1072H 4 TABLE I. Testing and inspection - Continued. 3/ Use focus coil JEDEC No. 109

14、 or No. 122 and 70 degree deflection coil JEDEC No. 118. 4/ For P25 phosphor, apply full raster to prevent screen burning. 5/ The phosphorescent light intensity observed (t) seconds after completion of the nth raster to the tube is Dt(N). cBf shall be the fluorescent light output under continuous ra

15、ster excitation. The screen characteristics shall be measured under the following conditions: a. Raster size (focused beam) 50 cm2with tube defocused to a spot approximately 0.25 cm (0.1 in) in diameter. b. Beam current: The tube operated at a current to produce 0.05 watt at the specified test volta

16、ge. c. Duration of raster: 1/60 second. d. Distance of raster from axis of calibrated 931VA multiplier tube: 30 cm (11.81 in). e. Red or white light: Sufficient to de-excite the phosphor before build-up measurements so that the results are within 3 cB of those that would have been obtained after tot

17、al de-excitation. 6/ The maximum diameters of “dead“ and “color“ spots shall be .060 inch. 7/ The tube shall be supported vertically on its face and rotated by a suitable adjustable turntable mechanism which will permit the neck to run true to the center of rotation of the turntable. A dial indicato

18、r perpendicular to the cone surface and .375 inch (9.53 mm) above the back of the faceplate metal lip shall be used to determine the amount of neck and bulb misalignment. The variation shall be no greater than the specified limit. 8/ With the tube supported as specified in 7/, the face tilt shall no

19、t exceed .375 inch (9.53 mm). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-1/1072H 5 NOTES: 1. Reference line determined by position where reference line gauge #110 will rest on glass funnel. 2. These dimensions are for reference only and

20、are not required for inspection purposes. FIGURE 1. Outline drawing of electron tube types 22CP7A and 22CP25A.Dimensions Ltr Inches Millimeters Min Max Min Max Qualification inspection M Base: B5-57 Conformance inspection, part 2 A - 22.063 - 560.40 B 21.625 21.875 549.28 555.63 C 1.375 1.500 34.93

21、38.10 D 20.000 - 508.00 - E 13.625 14.000 346.08 355.60 F 7.312 7.688 185.72 195.28 H .875 - 22.23 - J - 6.375 - 161.93 L .188 .438 4.78 11.13 Reference dimensions (see note 2) G 11.375 288.93 K 1.15 29.21 N 165.00 R 4191.00 R P .312 7.92 Q .656 16.66 R .438 11.13 S .25 R 6.35 R Provided by IHSNot f

22、or ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-1/1072H 6 In addition to MIL-PRF-1, this document references the following: MIL-STD-1311 Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of

23、the changes. Custodians: Preparing activity: Navy - EC DLA - CC DLA - CC Review activities: (Project 5960-2009-017) Navy - AS, CG, MC, OS NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-