DLA MIL-F-15733 2 L-2010 FILTERS RADIO FREQUENCY INTERFERENCE HERMETICALLY SEALED STYLE FL24 [Use DLA MIL-PRF-15733 73 B (1) DLA MIL-PRF-15733 73 B DLA MIL-PRF-15733 73A DLA MIL-PR.pdf

《DLA MIL-F-15733 2 L-2010 FILTERS RADIO FREQUENCY INTERFERENCE HERMETICALLY SEALED STYLE FL24 [Use DLA MIL-PRF-15733 73 B (1) DLA MIL-PRF-15733 73 B DLA MIL-PRF-15733 73A DLA MIL-PR.pdf》由会员分享，可在线阅读，更多相关《DLA MIL-F-15733 2 L-2010 FILTERS RADIO FREQUENCY INTERFERENCE HERMETICALLY SEALED STYLE FL24 [Use DLA MIL-PRF-15733 73 B (1) DLA MIL-PRF-15733 73 B DLA MIL-PRF-15733 73A DLA MIL-PR.pdf（7页珍藏版）》请在麦多课文档分享上搜索。

1、AMSC N/A FSC 5915 MIL-F-15733/2L 1 October 2010 SUPERSEDING MIL-F-15733/2K 27 February 2003 MILITARY SPECIFICATION SHEET FILTERS, RADIO FREQUENCY INTERFERENCE, HERMETICALLY SEALED, STYLE FL24 * This specification is approved for use by all Departments and Agencies of the Department of Defense. The r

2、equirements for acquiring the product described herein shall consist of this specification sheet and MIL-PRF-15733. FIGURE 1. Case dimensions and circuit diagram. Inactive for new design after 12 December 1988. For new design use MIL-PRF-15733/73. See table II for new design data. INCH-POUND Provide

3、d by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-F-15733/2L 2 FIGURE 1. Case dimensions and circuit diagram - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Dimensions. Dash number A B C D E F

4、 G Min Max Min Max Min Max Min Max Min Max Min Max 0001 2.500 (63.50) 2.624 (66.64) .813 (20.65) .937 (23.80) .141 (3.58) .312 (7.92) .360 (9.14) .390 (9.90) .187 (4.75) .312 (7.92) .432 (10.97) .445 (11.30) .09x.187 (2.3 x 4.75) 0002 3.813 (96.85) 3.937 (100.00) 1.063 (27.00) 1.187 (30.15) .141 (3.

5、58) .312 (7.92) .360 (9.14) .390 (9.90) .187 (4.75) .312 (7.92) .525 (13.34) .536 (13.61) .09x.187 (2.3 x 4.75) 0003 3.813 (96.85) 3.937 (100.00) 1.188 (30.18) 1.312 (33.32) .141 (3.58) .312 (7.92) .360 (9.14) .390 (9.90) .125 (3.18) .312 (7.92) .650 (16.51) .660 (16.76) .093 Dia (2.36) or .09 x .18

6、7 (2.3 x 4.75) 0004 4.063 (103.20) 4.187 (106.35) 1.313 (33.35) 1.437 (36.50) .308 (7.82) .624 (15.85) .360 (9.14) .390 (9.90) .308 (7.82) .624 (15.85) .650 (16.51) .660 (16.76) N/A 0005 4.094 (103.99) 4.218 (107.14) 1.438 (36.53) 1.562 (39.67) .308 (7.82) .624 (15.85) .360 (9.14) .390 (9.90) .308 (

7、7.82) .624 (15.85) .650 (16.51) .660 (16.76) N/A 0006 4.063 (103.20) 4.187 (106.35) 2.188 (55.58) 2.312 (58.72) .312 (7.92) .440 (11.18) .495 (12.57) .505 (12.82) .312 (7.92) .440 (15.85) 1.045 (26.54) 1.060 (26.92) N/A FIGURE 1. Case dimensions and circuit diagram - Continued. MIL-F-15733/2L3Provid

8、ed by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Dimensions Continued. Dash number H J K L M Mounting thread Terminal thread Terminal style Max weight lbs N Min Max Min Max Min Max Min Max Max Min Max 0001 .017 (.43) .027 (.69) .12 (3.1) .13 (3.3) .615 (15.

9、62) .698 (17.73) NA NA 3.63 (92.2) .500-28 UNEF-2A N/A 1 .19 N/A N/A 0002 .017 (.43) .055 (1.40) .12 (3.1) .161 (4.09) .802 (20.37) .885 (22.47) NA NA 4.95 (125.7) .625-24 UNEF-2A N/A 1 .46 N/A N/A 0003 .017 (.43) .027 (.69) .12 (3.1) .161 (4.09) .928 (23.57) 1.072 (27.23) NA NA 4.95 (125.7) .750-20

10、 UNEF-2A N/A 1 .6 N/A N/A 0004 .017 (.43) .027 (.69) .12 (3.1) .161 (4.09) .928 (23.57) 1.072 (27.23) .12 (3.1) .13 (3.3) 5.88 (149.4) .750-20 UNEF-2A .190-32 UNF-2A 2 .8 .36 (9.14) .38 (9.65) 0005 .017 (.43) .027 (.69) .12 (3.1) .161 (4.09) .928 (23.57) 1.072 (27.23) .12 (3.1) .13 (3.3) 5.88 (149.4

11、) .750-20 UNEF-2A .190-32 UNF-2A 2 .9 .36 (9.14) .38 (9.65) 0006 .057 (1.45) .067 (1.70) .182 (4.62) .192 (4.88) 1.615 (41.02) 1.635 (41.53) .095 (2.41) .105 (2.67) 6.31 (160.3) 1.125-18 UNEF-2A .250-28 UNF-2A 2 2.0 .432 (10.97) .442 (11.23) NOTES: 1. Dimensions are in inches. 2. Metric equivalents

12、are in parenthesis. 3. Metric equivalents are given for general information only. 4. Mounting hardware shall be supplied with the filter. 5. Circuit diagram is for information only. FIGURE 1. Case dimensions and circuit diagram - Continued. MIL-F-15733/2L4Provided by IHSNot for ResaleNo reproduction

13、 or networking permitted without license from IHS-,-,-5 MIL-F-15733/2L REQUIREMENTS: Dimensions and configuration: See figure 1. Case: Metal. * Case and mounting hardware finish: In accordance with MIL-PRF-15733. Pure tin finish is prohibited as specified in MIL-PRF-15733. Terminals: Style 1: Solder

14、able. Style 2: Threaded stud. * Recommended terminal torque: Thread Torque (in-lb) .190-32 UNF-2A 16 to 18 .250-28 UNF-2A 35 to 40 * Recommended mounting torque: Thread Torque (in-lb) Thread Torque (in-lb) .500-28 UNEF-2A 85 to 95 .750-20 UNEF-2A 120 to 140 .625-24 UNEF-2A 100 to 115 1.125-18 UNEF-2

15、A 150 to 175 Weight: See figure 1. Operating temperature range: -55C to +85C. Rated (power) frequency: 0 to 400 Hz. Rated voltage: See table I. Rated current: See table I. Insertion loss: In accordance with MIL-PRF-15733 and the following: (at +25C): See table I. (at -55C and +85C): Insertion loss s

16、hall be as specified in table I except that a degradation of 2 dB from the value specified in table I shall be allowed up to 10 MHz. Seal: In accordance with MIL-PRF-15733. Temperature rise: +25C maximum for parts rated up to and including 10 amperes. +35C maximum for parts rated above 10 amperes. D

17、ielectric withstanding voltage: In accordance with MIL-PRF-15733 except the duration of application of voltage shall be 1 to 5 seconds. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-F-15733/2L 6 TABLE I. Electrical characteristics. Dash number

18、Circuit diagram Rated voltage Rated current (A) Minimum insertion loss (dB) in accordance with MIL-STD-220 at +25C 1/ V dc V ac .15 MHz .30 MHz .60 MHz 1 MHz 10 MHz 100 MHz 1,000 MHz 0001 400 125 1 50 60 60 60 60 60 60 0002 400 125 5 50 60 60 60 60 60 60 0003 400 125 10 50 60 60 60 60 60 60 0004 400

19、 125 15 50 60 60 60 60 60 60 0005 400 125 20 50 60 60 60 60 60 60 0006 400 125 55 50 60 60 60 60 60 60 1/ Full load and no load insertion loss measurements shall be conducted at the specified frequency ranges in MIL-STD-220. Insulation resistance: In accordance with MIL-PRF-15733. Insulation resista

20、nce measured between both terminals connected together and the case shall be at least: Dash numbers 0001 and 0002 - 1,000 megohms 0003, 0004, 0005, and 0006 - 500 megohms Voltage drop: .5 volt, maximum. Terminal strength: In accordance with MIL-PRF-15733 and the following: Style 2: method 211, MIL-S

21、TD-202; test condition E. Style 1: method 211, MIL-STD-202; test conditions A (applied force: 5 pounds) and B (5 bends). Salt atmosphere (corrosion): In accordance with MIL-PRF-15733 and method 101, MIL-STD-202; test condition A. Shock (specified pulse): In accordance with MIL-PRF-15733 and method 2

22、13, MIL-STD-202; test condition I. Mounting: Filters shall be rigidly mounted by the body. Insertion loss shall be measured and shall meet initial requirements. Vibration, high frequency: In accordance with MIL-PRF-15733 and method 204, MIL-STD-202; test condition D (20g). Life: In accordance with M

23、IL-PRF-15733 and method 108, MIL-STD-202; test condition B (250 hr). Part or identifying number (PIN): M15733/02- (dash number from figure 1 and table I). * New design data: See table II. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-F-15733/2L

24、 7 * TABLE II. New design data. Inactive PIN Recommended PIN for new design use M15733/02-0001 M15733/73-0037 M15733/02-0002 M15733/73-0042 M15733/02-0003 M15733/73-0045 M15733/02-0004 M15733/73-0048 M15733/02-0005 M15733/73-0048 M15733/02-0006 M15733/73-0052 NOTES: * Referenced documents. In additi

25、on to MIL-PRF-15733, this specification sheet references the following documents: MIL-PRF-15733/73 MIL-STD-202 MIL-STD-220 * Changes from previous issue. The margins of this specification sheet are marked with an asterisk to indicate where changes from the previous issue were made. This was done as

26、a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations. Custodians: Preparing activity: Army

27、- CR DLA - CC Navy - EC Air Force - 85 (Project 5915-2010-006) DLA - CC Review activities: Army - AR, AT, AV, MI Navy - AS, MC, OS, SH Air Force - 19, 99 NOTE: The activities listed above were interested in the document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-