DLA MIL-DTL-32000-2003 PAINT FACE CAMOUFLAGE《涂料外观伪装》.pdf

《DLA MIL-DTL-32000-2003 PAINT FACE CAMOUFLAGE《涂料外观伪装》.pdf》由会员分享，可在线阅读，更多相关《DLA MIL-DTL-32000-2003 PAINT FACE CAMOUFLAGE《涂料外观伪装》.pdf（19页珍藏版）》请在麦多课文档分享上搜索。

1、Beneficial comments (recommendations, additions, deletions) and any pertinent data that may be of use in improving this document should be addressed to: Defense Supply Center Richmond, ATTN: DSCR-VBD, 8000 Jefferson Davis Highway, Richmond, VA 23297-5610 by using the Standardization Document Improve

2、ment Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC N/A FSC 6850 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. NOT MEASUREMENT SENSITIVE MIL-DTL-32000 10 January 2003 DETAIL SPECIFICATION PAINT, FACE, CAMOUFLAGE This specification

3、 is approved for use by all departments and agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers two types of camouflage face paint having visual and near-infrared (NIR) properties in a compact-style container with five colors for use on exposed skin such as the face,

4、 neck, and hands. 1.2 Classification. The face paint should be of the following types (see 6.2): Type I - Contains no insect repellent. Type II - Contains insect repellent N,N-diethyl-meta-toluamide (DEET). 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in se

5、ctions 3 and 4 of this specification. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must

6、meet all specified requirements of the documents cited in sections 3 and 4 of this specification, whether or not they are listed. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-32000 2 2.2 Government documents. 2.2.1 Standards. The following

7、 standards form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents should be those listed in the issue of the Department of Defense Index of Specifications and Standards (DoDISS) and supplement thereto, cited in the solicitation (see 6.2

8、). STANDARDS FEDERAL FED-STD-595 - Colors Used in Government Procurement. MILITARY MIL-STD-1916 - DoD Preferred Methods for Acceptance of Product. (Unless otherwise indicated, copies of the above standards are available from the Standardization Documents Order Desk, 700 Robbins Avenue, Building 4D,

9、Philadelphia, PA 19111-5094. Electronic copies of federal and military standards may be obtained from http:/astimage.daps.dla.mil/quicksearch/.) 2.2.2 Other government publications. The following other government publications form a part of this document to the extent specified herein. Unless otherw

10、ise specified, the issues are those cited in the solicitation (see 6.2). CODE OF FEDERAL REGULATIONS (CFR) 21 CFR 73 - Listing of Color Additives Exempt from Certification. 21 CFR 74 - Listing of Color Additives Subject to Certification. 21 CFR 82 - Listing of Certified Provisionally Listed Colors a

11、nd Specifications. 21 CFR 700 - 740 - Food and Drug Administration, Department of Health and Human Services. 40 CFR 152 - 180 - Environmental Protection Agency. UNITED STATES CODE (USC) 7 USC 136 et seq. - Federal Insecticide, Fungicide, and Rodenticide Act. 21 USC 301 et seq. - Federal Food, Drug,

12、and Cosmetic Act. (Application for copies should be addressed to the Superintendent of Documents, P.O. Box 371954, Pittsburgh, PA 15250-7954. Electronic copies may be obtained from http:/www.access.gpo.gov/.) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from I

13、HS-,-,-MIL-DTL-32000 3 2.3 Non-government publications. The following documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues of documents that are DoD adopted are those listed in the issue of the DoDISS cited in the solicitation. Unless otherwis

14、e specified, the issues of the documents not listed in the DoDISS are the issues of documents cited in the solicitation (see 6.2). ASTM INTERNATIONAL ASTM D 523 - Standard Test Method for Specular Gloss (DoD adopted). ASTM D 1729 - Standard Practice for Visual Appraisal of Colors and Color Differenc

15、es of Diffusely-Illuminated Opaque Materials (DoD adopted). ASTM D 2244 - Standard Test Method for Calculation of Color Differences From Instrumentally Measured Color Coordinates (DoD adopted). ASTM D 4101 - Standard Specification for Polypropylene Injection and Extrusion Materials (DoD adopted). (A

16、pplication for copies should be addressed to ASTM International, 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428-2959. Electronic copies may be obtained from http:/www.astm.org/.) SOCIETY OF AUTOMOTIVE ENGINEERS (SAE) SAE AMS5513 - Steel, Corrosion Resistant, Sheet, Strip, and Plat

17、e 19Cr - 9.2Ni (SAE 30304) Solution Heat Treated. SAE AMS-P-83310 - Plastic Sheet, Polycarbonate, Transparent. (Application for copies should be addressed to the Society of Automotive Engineers, 400 Commonwealth Drive, Warrendale, PA 15096-0001. Electronic copies may be obtained from http:/www.sae.o

18、rg/.) AMERICAN ASSOCIATION OF TEXTILE CHEMISTS AND COLORISTS (AATCC) - Instrumental Colour Formulation, A Practical Guide. - Technical Manual of the American Association of Textile Chemists and Colorists. (Applications for copies should be addressed to the AATCC National Headquarters, P.O. Box 12215

19、, Research Triangle Park, NC 27709-2215. Electronic copies may be obtained from http:/www.aatcc.org/.) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-32000 4 INTERNATIONAL ORGANIZATION FOR STANDARDIZATION (ISO) ISO 10526 - CIE Standard Illum

20、inants for Colorimetry. (Application for copies should be addressed to International Organization for Standardization (ISO), 1, rue de Varemb, Case postale 56, CH-1211 Geneva 20, Switzerland. Electronic copies may be obtained from http:/www.iso.ch/.) 2.4 Order of precedence. In the event of a confli

21、ct between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 First article. When specified (see 6.2),

22、a sample shall be subjected to first article inspection in accordance with 4.2. 3.2 Container. 3.2.1 Material. The compact-style container shall be of a polymer plastic material such as polypropylene made in accordance with ASTM D 4101 with a matte finish inside and out. The polymer plastic material

23、 used for the type II face paint compact-style container shall be chemically resistant to DEET. 3.2.2 Physical characteristics. The compact-style container shall have rounded corners and its overall dimensions should be in accordance with figure 1. The container cover shall be all-over rough grained

24、 or sandy surfaced, fit snugly on all sides and be able to withstand temperatures of 20 F through 120 F (-7 C through 49 C) without distortion or deterioration over a maximum shelf life of three years. The container shall contain separate compartments for each of the five colors in accordance with f

25、igure 2. Container dimension variation may be negotiated with the contracting organization. 3.2.2.1 Cover. The compact cover shall have a positive closure and shall be permanently attached to the base by a single hinge (see figures 1 and 2). The closure and hinge shall allow the cover of the contain

26、er to open and close with only a reasonable amount of effort and with a minimum amount of noise. The hinge shall be able to withstand 100 open and close cycles of the compact. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-32000 5 FIGURE 1.

27、Closed compact view. FIGURE 2. Open compact view. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-32000 6 3.2.2.2 Compartments. Type I and type II compact-style containers shall have five compartments to hold five face paint colors. The dimen

28、sions of the five compartments shall be in accordance with figure 2. The compartments shall be filled with face paints in accordance with figure 2. Each compartment shall provide for retention of the face paint within the compartment after shrinkage of the face paint. 3.2.2.2.1 The compartments shal

29、l be foil sealed. For type II, a DEET resistant foil shall cover each face paint formulation using a DEET resistant sealing method. 3.2.3 Container color. Colors for the containers shall be in accordance with paragraphs 3.2.3.1 and 3.2.3.2. The matte finish shall have a specular gloss factor not ove

30、r 45 gloss units (GU) in accordance with ASTM D 523. 3.2.3.1 Type I. The container shall be olive drab in accordance with FED-STD-595 color number 34096. 3.2.3.2 Type II. The container shall be brown in accordance with FED-STD-595 color number 30051. 3.2.4 Mirror. Each compact-style container shall

31、have a mirror inside the cover of the container. The material and thickness of the mirror shall be in accordance with table I. The mirror shall be of appropriate dimensions for the container lid and shall be securely affixed inside the lid. The method used for affixing the mirror to the container li

32、d for the type II compact shall be resistant to the effects of DEET. TABLE I. Mirror material and thickness. Face paint Material Thickness (inches) Type I Polycarbonate in accordance with SAE AMS-P-83310 0.062 Type II Unbreakable mirror polished stainless steel in accordance with SAE AMS5513 and SSI

33、NA1No. 8 Finish 0.019 1Specialty Steel Industry of North America. 3.3. Labels. Each container shall be legibly and neatly labeled. The label shall show no softening, smudging, removal, or illegibility. Figure 3 provides an example for the type I label and figure 4 provides an example of the type II

34、label. If the label is printed, it shall be on a matte-finished transparent material or an opaque material the same color as the container. The label shall have the same gloss properties as the container. The color of the label lettering and the location on the compact-style container shall be in ac

35、cordance with paragraphs 3.3.1, 3.3.2, and 3.3.6. The label for type I face paint shall be in compliance with 21 USC 301 et seq. The label for type II face paint shall be registered with the Pesticide Registration Division, Environmental Protection Agency (EPA) and shall be in compliance with the re

36、quirements of the Federal Insecticide, Fungicide, and Rodenticide Act (FIFRA) as specified in 7 USC 136 et seq., as amended. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-32000 7 National stock number Trade name and “Camo Face Paint“ Specif

37、ication number Name of manufacturer or supplier Date of manufacture NOTICE CAUTION - Avoid contact with eyes TO USE: Apply with finger for application to face, neck, and hands. STORAGE AND DISPOSAL: Store in a cool, dry area, away from heat. FIGURE 3. Example of type I label. 3.3.1 Type I label. The

38、 lettering for the type I label shall be stenciled or printed in black in accordance with FED-STD-595 color number 37038 or molded into the container. The label shall be located on the topside of the container. 3.3.2 Type II label. The lettering for the label shall be stenciled or printed in tan in

39、accordance with FED-STD-595 color number 36415 or molded into the container. The label shall be located on the topside of the container. National stock number Specification number Date of manufacture Trade Name and “Camo Face Paint with INSECT REPELLENT“ KEEP OUT OF THE REACH OF CHILDREN CAUTION See

40、 additional precautionary statements on back panel. ACTIVE INGREDIENTS: DEET .30.00% OTHER INGREDIENTS: .70.00% Net Contents: # Copyright1999 Manufactured by: EPA Reg. No.: #-# Name of Manufacturer EPA Est. No.: #-#-# Manufacturers Address Manufacturers Telephone Number FIGURE 4. Example of type II

41、label for top side of compact. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-32000 8 3.3.4 Label data for type I. Label data for face paint type I shall include: a. National stock number. b. Trade name and “Camo Face Paint“. c. Specificatio

42、n number. d. Name of manufacturer or supplier. e. Date of manufacture. f. “Notice“ and “Caution“ statement. g. Directions for use. h. Directions for storage and disposal. 3.3.5 Label data for type II. Label data for face paint type II shall include: a. National stock number. b. Specification number.

43、 c. Date of manufacture. d. Trade name and “Camo Face Paint With INSECT REPELLENT“. The words “INSECT“ and “REPELLENT“ shall be in capital letters and bold-faced type. e. Statement “Keep Out of the Reach of Children“. f. Word “CAUTION“ with cautionary statement. g. Name and percent of active ingredi

44、ent and the percent of total inactive ingredients and net contents. h. Manufacturers name. i. Manufacturers address. j. Manufacturers telephone number. k. EPA registration number and EPA establishment number in accordance with 40 CFR 152 - 180 (see 6.2). l. Directions for use. m. Precautionary state

45、ment. n. First aid statement. o. Storage and disposal statement. 3.3.6 Instructions for type II face paint. The lettering for the label shall be stenciled or printed in tan in accordance with FED-STD-595 color number 36415 or molded into the container. The directions for use shall be located on the

46、bottom side of the container. Figure 5 provides an example of the bottom side label for a type II container. Trade name and “Camo Face Paint with INSECT REPELLENT“ is a camouflage makeup specially formulated to repel mosquitoes, ticks, chiggers, deer flies, stable flies, black flies, fleas, and gnat

47、s on exposed skin surfaces. DIRECTIONS FOR USE: It is a violation of federal law to use this product in a manner inconsistent with its labeling. Read and follow all directions and precautions on this product label. Apply to hand for application to face and neck. Do not get in eyes or on lips. Do not

48、 apply over cuts, wounds, or irritated skin. Wipe palms and fingertips after applying. Use just enough face paint to cover skin. Do not use under clothing. Avoid over application of this product. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DT

49、L-32000 9 Frequent reapplication and saturation is unnecessary for effectiveness. After returning to indoors, wash treated skin with soap and water. Safe to use with Battle Dress Uniform. Safe to use with cotton and wool. Do not apply to synthetic fabrics other than nylon or polyester. May damage furniture finishes, plastics, linoleum, painted surfaces, and watch crystals. For use on children: