DLA DSCC-DWG-85027 REV E-2012 ADAPTER CONNECTOR BNC TO DUAL BANANA JACK.pdf

《DLA DSCC-DWG-85027 REV E-2012 ADAPTER CONNECTOR BNC TO DUAL BANANA JACK.pdf》由会员分享，可在线阅读，更多相关《DLA DSCC-DWG-85027 REV E-2012 ADAPTER CONNECTOR BNC TO DUAL BANANA JACK.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、REVISIONS LTR DESCRIPTION DATE APPROVED A Change part number. 25 Nov 1987 R. Marbais B Added note after part number. 08 Sep 1995 R. Larson C Dimension change on figure 1 to .161 .005. 31 Mar 2003 R. Taylor D Tolerance change on figure 1 to 2.50 .035 . 07 February 2011 A. Abdouni E Update Vendor info

2、rmation. Editorial changes throughout. 28 August 2012 A. Abdouni Prepared in accordance with ASME Y14.100 Source control drawing REV PAGE REV STATUS OF PAGES REV E E E PAGE 1 2 3 PMIC N/A PREPARED BY DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO 43216-5000 Jeff Bohannon Original date of drawing 9 S

3、eptember 85 CHECKED BY TITLE George McCann ADAPTER, CONNECTOR, BNC TO DUAL BANANA JACK APPROVED BY Richard Marbais SIZE CAGE CODE DWG. NO. 85027 A 037Z3 REV E PAGE 1 OF 3 AMSC N/A 5935-E844-001 CURRENT DESIGN ACTIVITY CAGE CODE 037Z3 HAS CHANGED NAMES TO: DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3

4、990 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 SIZE CAGE CODE DWG NO. A 037Z3 85027 REV E PAGE 2 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3.

5、 Tolerance for overall length of the banana plug receptacle is .035. 4. Unless otherwise specified, tolerances are .01 (0.3 mm). FIGURE 1. Configuration and dimensions. ENGINEERING DATA: Nominal impedance: (50 ohms -1), (75 ohm -2). Frequency range: 0 to 100 MHz. Inches mm .005 0.127 .016 0.41 .04 1

6、.02 .14 3.56 .161 4.09 .250 6.35 .44 11.18 .593 15.06 .750 19.05 1.15 29.21 2.50 63.50 .035 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 SIZE CAGE CODE DWG NO. A 037Z3 85027 REV E PAGE 3 Volt

7、age rating: 500 V rms at sea level. Operating temperature: -50C to +50C. REQUIREMENTS: See DSCC drawing 85025 for basic specifications. Dimensions and configuration: See figure 1. Force to engage and disengage: Longitudinal force: Not applicable. Torque: 2 inch-pounds maximum. Coupling proof torque:

8、 15 inch-pounds minimum. Center contact retention: 6 pounds minimum axial force. Contact resistance (in milliohms, maximum): Test Voltage (drop) Initial 6 mv After vibration 10 mv After salt spray (corrosion) 15 mv Dielectric withstanding voltage at sea level: 1000 V rms, minimum. Part or Identifyin

9、g Number (PIN): 85027-1 Only the package need be marked with the military PIN, part to be marked using standard commercial practice. An approved source of supply is listed herein. Additional sources will be added as they become available. The vendors listed have agreed to the contents of this drawin

10、g and a certificate of compliance has been submitted to DLA Land and Maritime, PO Box 3990, Columbus, OH 43218, ATTN: VAI: RF Connectors/Cables. DSCC drawing PIN Vendor CAGE number Vendors similar PIN 1/ 85027-1 4U744 1296 91967 1688AA 1/ Parts must be purchased to this DSCC PIN to assure that all p

11、erformance requirements and tests are met. Vendor CAGE Vendor name number and address 4U744 Pomona Electronics 9028 Evergreen Way Everett, WA 98204 United States 91967 Abbatron 632 Arch Street Meadville PA 16335 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-