DLA A-A-59590 6 D-2013 HOLDER ELECTRICAL CARD WEDGE RETAINERS 3 PIECE SCREW ACTUATED DRIVE 225 X 260 INCH BODY SIZE WITH VISUAL LOCK AND SCREW RETENTION.pdf

《DLA A-A-59590 6 D-2013 HOLDER ELECTRICAL CARD WEDGE RETAINERS 3 PIECE SCREW ACTUATED DRIVE 225 X 260 INCH BODY SIZE WITH VISUAL LOCK AND SCREW RETENTION.pdf》由会员分享，可在线阅读，更多相关《DLA A-A-59590 6 D-2013 HOLDER ELECTRICAL CARD WEDGE RETAINERS 3 PIECE SCREW ACTUATED DRIVE 225 X 260 INCH BODY SIZE WITH VISUAL LOCK AND SCREW RETENTION.pdf（11页珍藏版）》请在麦多课文档分享上搜索。

1、 INCHPOUND AA59590/6D 6 July 2013 SUPERSEDING AA59590/6C 6 October 2010 COMMERCIAL ITEM DESCRIPTION SPECIFICATION SHEET HOLDER, ELECTRICAL CARD, WEDGE RETAINERS, 3 PIECE, SCREW ACTUATED DRIVE 225 X .260 INCH BODY SIZE, WITH VISUAL LOCK AND SCREW RETENTION The General Services Administration has auth

2、orized the use of this commercial item description for all federal agencies. The complete requirements for procuring electrical card holders described herein shall consist of this document and the latest issue in effect of AA59590. CLASSIFICATION/PART IDENTIFICATION NUMBER (PIN). This commercial ite

3、m description (CID) specification sheet uses a classification system which is included in the Part Identification Number (PIN) as shown in the following example (see notes). AA59590 CID number /06 Applicable CID specification sheet B, C, H, R Finish * Mounting * * Length (see table I) D, E, W Config

4、uration (see table II) Example: AA59590/06CK63 is the PIN for a chemical film finished, 6.3 inch (160.0 mm) long card holder with a retained actuating screw. The card holder also has three counterbored through holes for use with rivet fasteners. SALIENT CHARACTERISTICS. Performance. Card holders sha

5、ll hold the circuit card assembly firmly in its installed position. When the card holder is installed properly, it is capable of withstanding 60g/6ms of shock, 25 G-rms of vibration, and provides from 2 to 4 degrees C/W/inch thermal resistance transfer between the circuit card assembly and the heat

6、sink surfaces. Material. Unless otherwise specified herein, the card holder materials shall be as specified in AA59590. Interface and physical dimensions. The card holders supplied to this CID specification sheet shall be as specified on figures 1, 2, 3, 4, 5, in table I, table II, and AA59590. Actu

7、ating screw hex drive socket. The across flats dimension for the hex drive socket shall be as follows: .094 inch (2.38 mm) for mounting options “J“, “K“, “N“, “T“, “R“, “V“, and “S“ and 2.5 mm (0.098 inch) for mounting options “G“ and “M“. Cold plate slot width dimensions (when applicable). The reco

8、mmend cold plate slot width to accommodate the circuit card assembly with attached card holder is .300 inch (7.62 mm) plus the thickness of the printed board of the circuit card assembly (see AA59590). Nominal installation torque. When card holders are used in cold plate applications, the nominal in

9、stallation torque of each card holder shall be as follows: 6 inchpounds (0.68 Nm) for assemblies of the base configuration or configuration “W“ and 8 inchpounds (0.90 Nm) for assemblies of configurations “E“ or “D“. AMSC N/A FSC 5998 Provided by IHSNot for ResaleNo reproduction or networking permitt

10、ed without license from IHS-,-,-AA59590/6D 2 Inches mm Inches mm Inches mm Inches mm .225 .240 5.72 6.09 .250 .25 6.35 6.35 .270 .30 6.86 7.6 .325 .70 8.26 17.8 NOTES: 1. Dimensions are in inches. Millimeters are given for general information only. 2. Unless otherwise specified, tolerances are .02 i

11、nch (0.51 mm) for two place decimals and .010 inch (0.25 mm) for three place decimals. 3. The across flats dimension for hex drive socket shall be .094 inch (2.38 mm) for mounting options “J“, “K“, “N“, “T“, “R“, “V“, and “S“. The across flats dimension for hex drive socket shall be a hard metric di

12、mension of .098 inch (2.5 mm) across flats for mounting options “G“ and “M“. 4. Dimension shall be .20 inch (5.1 mm) maximum on card holders of the base configuration or configuration “E“ and .30 inch (7.6 mm) maximum on card holders of configuration “W“ or “D“. FIGURE 1. Relaxed and expanded dimens

13、ions. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/6D 3 Screw retention locknut (see figure 2). The card holder shall have a screw retention locknut intended to prevent unintentional disassembly of the card holder. The locknut shall be fab

14、ricated of a corrosion resistant material. FIGURE 2. Screw retaining self-locking nut (corrosion resistant) details. Visual lock indicator (see figure 3). The card holder shall have a visual indicator to show when the card holder is in its relaxed (unlocked) state. When the card holder is in the unl

15、ocked (relaxed) state, the actuating end of the screw shall display a red band on the side of the screw. When the actuating screw on the card holder has been tightened (assembly expanded) so that the assembly is in the locked position, this red band shall be concealed. FIGURE 3. Visual lock indicato

16、r. TABLE I. Additional assembly dimensions (see figure 1). 1/ PIN length designator Dimension “LENGTH“ .02 (0.5) Dimension “A“ (maximum) Dimension “B“ .03 (0.8) Dimension “C“ .005 (0.13) Without option “W“ or “D“ With option “W“ or “D“ 18 1.8 (45.7) 2.30 (58.4) 2.40 (60.9) 1.30 (33.0) .75 (19.1) 23

17、2.3 (58.4) 2.80 (71.1) 2.90 (73.7) 1.80 (45.7) .40 (10.2) 28 2.8 (71.1) 3.30 (83.8) 3.40 (86.4) 2.30 (58.4) .90 (22.9) 30 3.0 (76.2) 3.50 (88.9) 3.60 (91.4) 2.50 (63.5) 1.10 (27.9) 33 3.3 (83.8) 3.80 (96.5) 3.90 (99.1) 2.80 (71.1) 1.40 (35.6) 35 3.5 (88.9) 4.00 (101.6) 4.10 (104.1) 3.00 (76.2) 1.60

18、(40.6) 38 3.8 (96.5) 4.30 (109.2) 4.40 (111.8) 3.30 (83.8) 1.90 (48.3) 43 4.3 (109.2) 4.80 (121.9) 4.90 (124.5) 3.80 (96.5) 2.40 (61.0) 48 4.8 (121.9) 5.30 (134.6) 5.40 (137.2) 4.30 (109.2) 2.90 (73.7) 53 5.3 (134.6) 5.80 (147.3) 5.90 (149.9) 4.80 (121.9) 3.40 (86.4) 55 5.5 (139.7) 6.00 (152.4) 6.10

19、 (154.9) 5.00 (127.0) 3.60 (91.4) 58 5.8 (147.3) 6.30 (160.0) 6.40 (162.6) 5.30 (134.6) 3.90 (99.1) See footnote at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/6D 4 TABLE I. Additional assembly dimensions (see figure 1) Cont

20、inued. PIN length designator Dimension “LENGTH“ .02 (0.5) Dimension “A“ (maximum) Dimension “B“ .03 (0.8) Dimension “C“ .005 (0.13) Without option “W“ or “D“ With option “W“ or “D“ 61 6.1 (154.9) 6.60 (167.6) 6.70 (170.2) 5.60 (142.2) 4.20 (106.7) 63 6.3 (160.0) 6.80 (172.7) 6.90 (175.3) 5.80 (147.3

21、) 4.40 (111.8) 67 6.7 (170.2) 7.20 (182.9) 7.30 (185.4) 6.20 (157.5) 4.80 (121.9) 68 6.8 (172.7) 7.30 (185.4) 7.40 (188.0) 6.30 (160.0) 4.90 (124.5) 73 7.3 (185.4) 7.80 (198.1) 7.90 (200.7) 6.80 (172.7) 5.40 (137.2) 78 7.8 (198.1) 8.30 (210.8) 8.40 (213.4) 7.30 (185.4) 5.90 (149.9) 83 8.3 (210.8) 8.

22、80 (223.5) 8.90 (226.1) 7.80 (198.1) 6.40 (162.6) 88 8.8 (223.5) 9.30 (236.2) 9.40 (238.8) 8.30 (210.8) 6.90 (175.3) 1/ Dimensions are in inches. Millimeters, in parenthesis, are given for general information only. Cold plate slot width dimensions (when applicable). The recommend cold plate slot wid

23、th to accommodate the circuit card assembly with attached card holder is .300 inch (7.62 mm) plus the thickness of the printed board of the circuit card assembly (see AA59590). Finish. The finish designator shall be as specified in AA59590. The wedge body finishes available for this CID specificatio

24、n sheet are as follows: “B“ (black anodize), “C“ (gold chemical film), “H“ (hard black anodize), or “R“ (clear chemical film). Mounting options. The mounting designators shall be as specified in AA59590. The mounting options available for this CID specification sheet are as follows: “J“ or “K“ (rive

25、t mounting holes), “N“ (no mounting holes), “T“ or “R“ (tapped 080 UNF 2B holes), “V“ or “S“ (tapped 256 UNC 2B holes), or “G“ or “M“ (tapped M2.5 x.45 metric holes). Card holders using mounting option “J“ or “K“ may be shipped unassembled. See figure 1 for mounting hole spacing requirements. Mounti

26、ng holes and locations (when required). When not using mounting option “N“, mounting holes will be present in the center body (see figure 1). Two mounting holes are required on card holders less than 5.30 inches (134.6 mm) in length. Three mounting holes are required on card holders 5.30 inches (134

27、.6 mm) or greater in length. The third mounting hole shall be centered on the mounting body. See figure 1 and table I for mounting hole locations and spacing requirements. Rivet mounting holes. The holes used for rivet mounting shall be .066 to .073 inch (1.68 to 1.85 mm) diameter through holes, cou

28、ntersunk 100 degrees by .140 inch (3.56 mm) diameter with an access/clearance counterbore hole of .156 inch (3.96 mm) diameter by .200 inch (5.08 mm) deep. Rivets. This card holder uses rivet style A as specified in AA59590 when rivet mounting is used. Length, expanded, and relaxed dimensions. The l

29、ength, expanded, and relaxed dimensions shall be as specified on figure 1. The length designator shall be as specified in AA59590 and the available lengths for this CID specification sheet are listed in table I. Provided by IHSNot for ResaleNo reproduction or networking permitted without license fro

30、m IHS-,-,-AA59590/6D 5 Configuration. The configuration of a card holder shall be as specified in table II. The details of a particular configuration consist of those on figures 1, 2 and 3, and may include those on figures 4 and 5. Card holders not requiring the options described by table II shall l

31、eave the configuration position in the PIN blank. TABLE II. Configuration. Configuration Applicable figures Hardware options 1, 2, and 3 No added options W 1, 2, 3, and 4 Lockwasher and flat washer E 1, 2, 3, and 5 Screw self-locking element D 1, 2, 3, 4, and 5 Lockwasher, flat washer and screw self

32、-locking element Lockwasher and flat washer (see figure 4). The use of a lockwasher and flat washer located under the screw head will provide for additional resistance to loosening of the card holder assembly from shock and vibration. Card holders requiring a lockwasher and flat washer shall include

33、 a suffix “W“ in the PIN (see classification and notes herein). FIGURE 4. Lockwasher and flat washer details. Screw self-locking element (see figure 5). The use of a screw self-locking element on the screw will provide a prevailing-torque for increased resistance to loosening of the card holder asse

34、mbly from shock and vibration. The screw self-locking element shall be as specified in AA59590. Card holders requiring a screw self-locking element shall include configuration identifier “E“ in the PIN (see classification and notes herein). FIGURE 5. Screw self-locking element details. Lockwasher, f

35、lat washer, and screw self-locking element. Card holders requiring a lockwasher, flat washer, and screw self-locking element configuration shall include a suffix “D“ in the PIN (see classification and notes herein). NOTES. PIN. The PIN should be used for Government purposes to buy commercial product

36、s to this CID specification sheet. See the classification section for PIN format example. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/6D 6 Source of documents. Commercial Item Description AA59590 Holder, Electrical Card, Wedge Retainers,

37、3 Piece, Screw Actuated Drive, General Requirements For. (Copies of these documents are available online at http:/quicksearch.dla.mil or https:/assist.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 191115094.) Ordering data. Ordering data s

38、hall be as specified in AA59590. Commercial products. As part of the market analysis and research effort, this CID specification sheet was coordinated with the following manufacturers of commercial products. At the time of CID specification sheet preparation and coordination, these manufacturers wer

39、e known to have commercial products that would meet the requirements of this CID specification sheet. (NOTE: This information should not be considered as a list of approved manufacturers or be used to restrict procurement to only the manufacturers shown.) Manufacturer CAGE Manufacturer name and addr

40、ess Manufacturer contact information 18915 Birtcher A Division of Pentair Electronic Packaging 7328 Trade Street San Diego, CA 921213410 Telephone: (858) 7402400 Toll Free: (800) 8547086 Facsimile: (858) 7402430 (URL): 61081 Calmark A Division of Pentair Electronic Packaging 7328 Trade Street San D

41、iego, CA 921213410 Telephone: (858) 7402400 Toll Free: (800) 8547086 Facsimile: (858) 7402430 Electronic mail: URL: 5BG68 American Circuit Card Retainers, Inc. 2310 E. Orangethorpe Avenue Anaheim, CA 928061231 Telephone: (714) 7386194 Facsimile: (714) 4460119 E-mail: URL: http:/ 3E7U8 Wakefield S

42、olutions 200 Towerview Court Cary, NC 27513 Telephone: (919) 4692004 Facsimile: (919) 4692827 E-mail: URL: Part number supersession data. This CID specification sheet PINs supersede the following manufacturers part numbers as shown in table III. The CID PINs listed in table III are only for length

43、 designator “28“. See table IV for CID PIN construction using other available lengths for this specification sheet. This information is being provided to assist in reducing proliferation in the Government inventory system. Provided by IHSNot for ResaleNo reproduction or networking permitted without

44、license from IHS-,-,-AA59590/6D 7 TABLE III. Commercial part number supersession data. PIN designator AA59590/06 Vendor similar designator or type part number 1/ 2/ CAGE 18915 CAGE 61081 CAGE 5BG68 CAGE 3E7UB BJ28 40VI6BLN VA225CR2.80HR 3225VBA2.80HR 426B280RSBAV BN28 40VI6BLNA VA225CR2.80R 3225VBA2

45、.80R 426B280ASBAV BT28 40VI6BLNT VA225CR2.80T0R 3225VBA2.80T0R 426B280TSBAV BV28 40VI6BLNS VA225CR2.80T2R 3225VBA2.80T2R 426B280SSBAV BG28 40VI6BLNM MVA225CR2.80TM2.5R 3225MVBA2.80TM2.5R 426B280MMBAV BJ28E 40VI6BLNL VA225CR2.80HLR 3225VBA2.80HLR 426B280RSBAPV BN28E 40VI6BLNAL VA225CR2.80LR 3225VBA2.

46、80LR 426B280ASBAPV BT28E 40VI6BLNTL VA225CR2.80T0LR 3225VBA2.80T0LR 426B280TSBAPV BV28E 40VI6BLNSL VA225CR2.80T2LR 3225VBA2.80T2LR 426B280SSBAPV BG28E 40VI6BLNML MVA225CR2.80TM2.5LR 3225MVBA2.80TM2.5LR 426B280MMBAPV BJ28W 40VI6BLFLN WVA225CR2.80HR 3225VWBA2.80HR 426B280RSBWAV BN28W 40VI6BLFLNA WVA22

47、5CR2.80R 3225VWBA2.80R 426B280ASBWAV BT28W 40VI6BLFLNT WVA225CR2.80T0R 3225VWBA2.80T0R 426B280TSBWAV BV28W 40VI6BLFLNS WVA225CR2.80T2R 3225VWBA2.80T2R 426B280SSBWAV BG28W 40VI6BLFLNM MWVA225CR2.80TM2.5R 3225VWBA2.80TM2.5R 426B280MMBWAV BJ28D 40VI6BLFLNL WVA225CR2.80HLR 3225VWBA2.80HLR 426B280RSBWAPV BN28D 40VI6BLFLNAL WVA225CR2.80LR 3225VWBA2.80LR 426B280ASBWAPV BT28D 40VI6BLFLNTL WVA225CR2.80T0LR 3225VWBA2.80T0LR 426B280TSBWAPV BV28D 40VI6BLFLNSL WVA225CR2.80T2LR 3225VWBA2.80T2LR 426B280SSBWAPV BG28D 40VI6BLFLNML MWVA225CR2.80TM2.5LR 3225MVWBA2.80TM2.5LR 426B280MMBWAPV CJ28 40VI6LN V2