DLA A-A-55058-1992 CLUB POLICEMAN-S《警棍》.pdf

《DLA A-A-55058-1992 CLUB POLICEMAN-S《警棍》.pdf》由会员分享，可在线阅读，更多相关《DLA A-A-55058-1992 CLUB POLICEMAN-S《警棍》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、A-A-55058 84 9999774 0066907 O J I INCH-POUND I 27 May 1992 A-A-55058 COMMERCAL ITEM DESCRIPTION CLUB, POLICEMANS The General Services Administration has authorized the use of this Commercial Item Description in preference to MIL-C-3880. Salient Characteristics. The Club, Policemans shall be made fr

2、om hardwood and have a leather thong. club shall have one coat of a lacquer-type sanding sealer coats of a black pigmented lacquer, gloss finish (suitable for interior use). finished thong shall not be pieced or spliced. shall be centered and tied around the finished club in the thong groove provide

3、d. knotted together. the club with an indent of characters 1/4 inch high. The wood finish of the I (suitable for application on wood furniture) and a minimum of two The The leather thong A paste wood filler may also be used. The ends of the thong shall not be tied or The letters US shall be legibly

4、indented on , 0 Material. The hardwood shall be any of the following: ash (white), beech, birch (sweet or yellow), elm (rock), pecan, hickory, locust, maple (sugar), or oak (red or white). The thong shall be made from lace full grain, cattlehide leather, 8/64 inch thick, natural in color. Beneficial

5、 comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Defense Personnel Support Center, Clothing and Textiles Directorate, Attn: DPSC-FSSD, 2800 South 20th Street, Philadelphia, PA 19101-8419, by using the self

6、-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. msc N/A FSC 84.65 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited Provided by IHSNot for ResaleNo reproduction or networking permitted without

7、license from IHS-,-,-A-A-5505 84 m 9999774 0066908 2 A-A-5 5 05 8 Sizes and Measurements. The overall length of the club shall measure 22 2 1/2 inches; the striking surface shall have a 1/4 inch radius rounded end with a diameter of 1-5/16 2 1/4 inches for 4-1/2 2 1/4 inches and then constantly tape

8、ring down to 12 1/4 inch (for approximately 11 inches); on a 3/8 inch radius, the club returns to a 1-5/16 2 1/4 inch diameter for 1/4 inch, then a 1 + 1/4 inch diameter for 3/16 inch for the thong groove and back toa 1-5/16 2 1/4 inch diameter for 1/4 inch; the handle of the club should be approxim

9、ately 6 inches in length and 1-1/4 inches in diameter with a non-slip surface texture. The leather thong shall measure.a minimum of 30 inches and a maximum of 32 inches. Workmanship. After completion, the finished club shall be thoroughly cleaned, and all surfaces shall be smooth and free of machine

10、 gouges. Product Demonstration Model. When required, offerers shall submit samples of their intended production. The Product Demonstration Model will consist of units independently developed. Product Demonstration Models will be analyzed and evaluated by.the government. Evaluation criteria and basis

11、 for award are contained in the solicitation. Product Demonstration Models will be retained by the government. One (1) Product Demonstration Model approved by DPSC under the resultant contract will serve as a manufacturing standard for the corresponding production items delivered under this contract

12、. Offerers are advised that the Product Demonstration Model does not relieve the successful offerer of his responsibility to perform in accordance with the Commercial Item Description specified above. Responsibility for Inspection. The supplier is responsible for assuring the product conforms to the

13、 requirements. Club lots will be inspected to determine conformance with the Commercial Item Description and the successful offerers technical proposal as negotiated. Acceptability of club lots will be determined by the use of “Sampling Procedures and Tables for Inspection by Attributes“, ANSI/ASQC

14、21.4, published by the American Society for Quality Control. Sampling procedures will be designated by the Government at the time of award. The sample unit is one club. The club will be examined mercia1 type defects only. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without

15、 license from IHS-,-,-. A-A-55058 84 W 7779774 0066707 4 W I ! I ! , I 1 I I I l l l ! , I 1 I l I a A-A-5 5 05 8 Defects. The club shall be examined for the following defects: measurement of item not as specified; any knots, shake, splits, check, wane, decay, larval channels and holes; any surface

16、not sanded smooth and having machine marks, chipped or torn grain, and spur; any brush marks, orange peel, runs, wrinkles, drops, streaks, blushing; any area of thin or no film; wet or tacky finish; any trace of grit or coarse particles; glossfinish not uniform; measurement of thong not as specified

17、; pieced or spliced; any cut, hole, tear, or crack; any boney, stiff, loose or pipey areas; any soft spot; any discdloration or mildew; not centered and tied around the finished club in the thong groove; ends of the thong tied or knotted together. Packaqinq, Packinq, Markinq, and Palletization Packa

18、ging, packing, marking and palletization shall be in accordance with ASTM-D 3951, Standard Practice for Commercial Packaging, as specified for shipments to the Department of Defense, including Section 7. Note: Each shipping container shall contain only one National Stock Number (NSN). Unitized loads

19、, placing boxes on pallets, shall be used whenever total quantity for shipment to one destination exceeds 250 pounds (excluding the pallet) or 20 cubic feet. Pallets shall have a length of 40 inches and a width of 48 inches. including the pallet, shall not exceed 54 inches in height, 43 inches in le

20、ngth and 52 inches in width. The containers shall be bonded onto wing type commercial4-way Pallet loads, entry pallets. _ Note: All palletized loads shall contain only one NSN, to the maximum extent possible. When there is less than a pallet load per NSN, pallets may have containers not of the same

21、NSN, but the pallet shall be clearly marked “mixed“ and each applicable NSN shall be listed together with its total quantity. Source of Government Documents. documents are available from: Copies of Military and Federal Standardization Documents Order Desk Bldg. 4D 700 Robbins Avenue Philadelphia, PA

22、 19111-5094 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-. A-A-55058 84 9999974 0066710 O A-A-55058 1 Sources of Nonqovernment Documents. ANSI/ASQC 21.4 - Sampling Procedures and Tables For Inspection By Attributes (Applications for copies should

23、be addressed to American National Standards Institute, 1430 Broadway, New York, NY 10018- 3308. ) ASTM-D 3951 - Standard Practice for Commercial Packaging (Applications for copies should be addressed to American Society For Testing and Materials, 1916 Race Street, Philadelphia, PA 19103.) Custodians

24、: Navy - NU Air Force - 99 Civil Agency Coordinating Activity: GSA - FSS Review Activity: Preparing Activity: Army - GL DLA - CT Air Force - 82, 45 User Activities: Navy - MC Coast Guard - CG Project Number 8465-0093 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-