DIN ISO 9183-1-2011 Tools for pressing - Wear plates for press dies - Part 1 Typ A (ISO 9183-1 2008)《冲压工具 冲压模耐磨板 第1部分 A型(ISO 9183-1-2008)》.pdf

《DIN ISO 9183-1-2011 Tools for pressing - Wear plates for press dies - Part 1 Typ A (ISO 9183-1 2008)《冲压工具 冲压模耐磨板 第1部分 A型(ISO 9183-1-2008)》.pdf》由会员分享，可在线阅读，更多相关《DIN ISO 9183-1-2011 Tools for pressing - Wear plates for press dies - Part 1 Typ A (ISO 9183-1 2008)《冲压工具 冲压模耐磨板 第1部分 A型(ISO 9183-1-2008)》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、May 2011 Translation by DIN-Sprachendienst.English price group 8No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 25.

2、120.10!$o#.“1760011www.din.deDDIN ISO 9183-1Tools for pressing Wear plates for press dies Part 1: Type A (ISO 9183-1:2008)English translation of DIN ISO 9183-1:2011-05Werkzeuge der Stanztechnik Stollenfhrungen fr Werkzeuge der Stanztechnik Teil 1: Typ A (ISO 9183-1:2008)Englische bersetzung von DIN

3、ISO 9183-1:2011-05Outillage de presse Plaques de frottement Partie 1: Type A (ISO 9183-1:2008)Traduction anglaise de DIN ISO 9183-1:2011-05SupersedesDIN ISO 9183-1:1992-07www.beuth.deDocument comprises pagesIn case of doubt, the German-language original shall be considered authoritative.1204.11 A co

4、mma is used as the decimal marker. Contents Page National foreword .3 National Annex NA (informative) Bibliography.4 1 Scope 5 2 Normative references 5 3 Types and dimensions 6 3.1 Type A1 .6 3.2 Type A2 .9 4 Material .12 5 Designation 12 2 DIN ISO 9183-1:2011-05 National foreword This standard has

5、been prepared by Technical Committee ISO/TC 29 “Small tools”, Subcommittee SC 8 “Tools for pressing and moulding”. The responsible German body involved in its preparation was the Normenausschuss Werkzeuge und Spann-zeuge (Tools and Clamping Devices Standards Committee), Working Committee NA 121-03-0

6、2 AA Werk-zeuge der Stanztechnik. The text of ISO 9183-1:2008 has been adopted in this standard without any modification. This second edition cancels and replaces the first edition (ISO 9183-1:1990) which has been technically revised. Attention is drawn to the possibility that some of the elements o

7、f this document may be the subject of patent rights. DIN shall not be held responsible for identifying any or all such patent rights. DIN ISO 9183 consists of the following parts, under the general title Tools for pressing Wear plates for press dies: Part 1: Type A Part 2: Type B The DIN Standards c

8、orresponding to the International Standards referred to in this document are as follows: ISO 2768-1 DIN ISO 2768-1 ISO 4762 DIN EN ISO 4762 Amendments This standard differs from DIN ISO 9183-1:1992-07 as follows: a) specifications relating to type A1 and type A2 are now included in separate figures

9、and tables; b) thickness of type A2 has been modified; c) tables with dimensions and tolerances for type A1 and type A2 have been revised; d) the figures have been revised; e) normative references have been included; f) the standard has been editorially revised. Previous editions DIN ISO 9183-1: 199

10、2-07 3 DIN ISO 9183-1:2011-05 tNational Annex NA (informative) Bibliography DIN EN ISO 4762, Hexagon socket head cap screws DIN ISO 2768-1, General tolerances Tolerances for linear and angular dimensions without individual tolerance indications 4 DIN ISO 9183-1:2011-05 Tools for pressing Wear plates

11、 for press dies 1 Scope This part of ISO 9183 specifies the basic dimensions and tolerances in millimetres of wear for press dies, type A, intended for use mainly in large press dies. It also specifies the size and positions of the clearance holes for attachment. It gives material indications, and s

12、pecifies the designation of wear plates for press dies, type A, which meet the requirements of this part of ISO 9183. Two thicknesses of this type of wear plate are specified: type A1, with a thickness, t, of 20 mm, and type A2, with a thickness, t, of 12 mm. 2 Normative references The following ref

13、erenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 2768-1, General tolerances Part 1: Tolerances for linear and a

14、ngular dimensions without individual tolerance indications ISO 4762, Hexagon socket head cap screws Part 1: Typ A 5 DIN ISO 9183-1:2011-05 3 Types and dimensions 3.1 Type A1 The dimensions of type A1 wear plates shall conform to the indications in Figure 1, Figure 2 and Table 1. General tolerance: I

15、SO 2768-m dimensions in millimetres surface roughness values in micrometers Figure 1 Type A1 6 DIN ISO 9183-1:2011-05 Table 1 Dimensions for type A1 Dimensions in millimetres b1l1b2l2l3d1d2h Hexagonal socket 00,200,2H13 H13 0,50+ISO 4762 pieces 80 30 25 9 15 9 M8 25 2 100 50 25 125 75 25 160 110 25

16、50 200 150 25 13,5 20 13 M12 25 2 50 30 25 9 15 9 M8 25 2 80 30 25 100 50 25 125 75 25 160 110 25 80 200 150 25 13,5 20 13 M12 25 2 50 50 25 80 50 40 100 50 25 125 75 25 160 110 25 100 200 150 25 13,5 20 13 M12 25 2 50 75 25 80 75 40 13,5 20 13 M12 25 2 100 75 50 25 125 75 75 25 160 75 110 25 125 20

17、0 75 150 25 13,5 20 13 M12 25 3 50 110 25 80 110 40 13,5 20 13 M12 25 2 100 110 50 25 125 110 75 25 160 110 110 25 160 200 110 150 25 13,5 20 13 M12 25 3 7 DIN ISO 9183-1:2011-05 General tolerance: ISO 2768-m dimensions in millimetres Figure 2 Clearance hole patterns for type A1 8 DIN ISO 9183-1:201

18、1-05 3.2 Type A2 The dimensions of type A2 wear plates shall conform to the indications of Figure 3, Figure 4 and Table 2. General tolerance: ISO 2768-m dimensions in millimetres surface roughness values in micrometers Figure 3 Type A2 9 DIN ISO 9183-1:2011-05 Table 2 Dimensions for type A2 Dimensio

19、ns in millimetres b1l1l2Hexagonal socket 00,200,2ISO 4762 pieces 80 30 100 50 125 75 160 110 20 200 150 M8 20 2 80 30 100 50 125 75 160 110 30 200 150 M8 20 2 80 30 100 50 125 75 160 110 40 200 150 M8 20 2 80 30 100 50 125 75 160 110 50 200 150 M8 20 2 80 30 100 50 125 75 160 110 60 200 150 M8 20 2

20、80 30 100 50 125 75 160 110 80 200 150 M8 20 2 10 DIN ISO 9183-1:2011-05 General tolerance: ISO 2768-m Dimensions in millimetres Figure 4 Clearance hole patterns for type A2 11 DIN ISO 9183-1:2011-05 4 Material The choice of material is left to the manufacturers discretion. 5 Designation Wear plates

21、 in accordance with this part of ISO 9183 shall be designated by: a) “Wear plate”; b) reference to this part of ISO 9183, i.e. ISO 9183-1; c) its type (A1 or A2); d) its width, b1, in millimetres; e) its length, l1,in millimetres. EXAMPLE The designation for a wear plate for press dies, type A1 with a width of b1= 80 mm and a length l1= 100 mm is designated as follows: Wear plate ISO 9183-1 A1 80 100 12 DIN ISO 9183-1:2011-05