DIN EN ISO 15614-4-2005 Specification and qualification of welding procedures for metallic materials - Welding procedure test - Part 4 Finishing welding of aluminium castings (ISO .pdf

《DIN EN ISO 15614-4-2005 Specification and qualification of welding procedures for metallic materials - Welding procedure test - Part 4 Finishing welding of aluminium castings (ISO .pdf》由会员分享，可在线阅读，更多相关《DIN EN ISO 15614-4-2005 Specification and qualification of welding procedures for metallic materials - Welding procedure test - Part 4 Finishing welding of aluminium castings (ISO .pdf（20页珍藏版）》请在麦多课文档分享上搜索。

1、DEUTSCHE NORM September 2005DIN EN ISO 15614-4 No part of this standard may be reproduced without the prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).English price group 12w

2、ww.din.dewww.beuth.de01.06 9664507Continued overleaf.Document comprises 20 pages.Specication and qualication of welding procedures for metallic materialsWelding procedure testPart 4: Finishing welding of aluminium castings(ISO 15614-4:2005)English version of DIN EN ISO 15614-4Anforderung und Qualizi

3、erung von Schweiverfahren fr metallische Werkstoffe Schweiverfahrenspr-fung Teil 4: Fertigungsschweien von Aluminiumguss (ISO 15614-4:2005)National forewordThis standard has been published in accordance with a decision taken by CEN/TC 121 to adopt, without alteration, International Standard ISO 1561

4、4-4 as a European Standard.The responsible German body involved in its preparation was the Normenausschuss Schweitechnik (Weld-ing Standards Committee), Technical Committee NA 092-00-19 AA Schweien von Aluminium.This standard deals with nishing welding of aluminium castings. It does not apply to rep

5、air welding. For joint welding, DIN EN ISO 15614-2 applies.The European Standards referred to in clause 2 of the EN have been published as the corresponding DIN EN Standards with the same number. The International Standards listed correspond to the following DIN Standards:ISO 4063 DIN EN ISO 4063ISO

6、 9017 DIN EN 1320ISO 10042 DIN EN 30042ISO 14175 DIN EN 439ISO 15607 DIN EN ISO 15607ISO 15609-1 DIN EN ISO 15609-1ISO 15614-2 DIN EN ISO 15614-2ISO 17635 DIN EN 12062ISO 17636 DIN EN 1435ISO 17637 DIN EN 970ISO 17639 DIN EN 1321ISO/TR 15608 DIN V 1738ICS 25.160.10!,eP*“Page 2DIN EN ISO 15614-4:2005

7、-09National Annex NA (informative)BibliographyDIN EN 439 Welding consumables Shielding gases for arc welding and cuttingDIN EN 970 Non-destructive examination of fusion welds Visual examinationDIN EN 1320 Destructive tests on welds in metallic materials Fracture testDIN EN 1321 Destructive tests on

8、welds in metallic materials Macroscopic and microscopic exami-nation of weldsDIN EN 1435 Non-destructive testing of welds Radiographic testing of welded jointsDIN EN 12062 Non-destructive testing of welds General rules for metallic materialsDIN EN 30042 Arc-welded joints in aluminium and its weldabl

9、e alloys Guidance on quality levels for imperfectionsDIN EN ISO 4063 Welding and allied processes Nomenclature of processes and reference numbers (ISO 4063:1998)DIN EN ISO 15607 Specication and qualication of welding procedures for metallic materials General rules (ISO 15607:2003)DIN EN ISO 15609-1

10、Specication and qualication of welding procedures for metallic materials Welding procedure specication Part 1: Arc welding (ISO 15609-1:2004)DIN EN ISO 15614-2 Specication and qualication of welding procedures for metallic materials Welding procedure test Part 2: Arc welding of aluminium and its all

11、oys (ISO 15614-2:2005)DIN V 1738 Welding Guidelines for a metallic material grouping systemEnglish versionICS 25.160.10Management Centre: rue de Stassart, 36 B-1050 BrusselsEuropean Committee for StandardizationComit Europen de NormalisationEuropisches Komitee fr Normung 2005. CEN All rights of expl

12、oitation in any form and by any means reserved worldwide for CEN national members.Ref. No. EN ISO 15614-4:2005 EEN ISO 15614-4July 2005Specication and qualication of welding procedures for metallic materialsWelding procedure testPart 4: Finishing welding of aluminium castings(ISO 15614-4:2005)Descri

13、ptif et qualication dun mode opratoire de soudage pour les mat- riaux mtalliques preuve de qua-lication dun mode opratoire de soudage Partie 4: Rparation par soudage pour les travaux de nition des pices moules en aluminium (ISO 15614-4:2005)Anforderung und Qualizierung von Schweiverfahren fr metalli

14、sche Werkstoffe Schweiverfahrens-prfung Teil 4: Fertigungs-schweien von Aluminiumguss (ISO 15614-4:2005)This European Standard was approved by CEN on 2005-06-20.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard

15、the status of a national standard without any alteration.Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.The European Standards exist in three ofcial versions (English, French, German). A v

16、ersion in any other language made by translation under the responsibility of a CEN member into its own language and notied to the Management Centre has the same status as the ofcial versions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, the Czech Republic, Denmark, Eston

17、ia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland, and the United Kingdom.Page 2EN ISO 15614-4:2005Foreword International StandardISO 15614-4:2005 Spe

18、cication and qualication of welding procedures for metallic materials Welding pro-cedure test Part 4: Finishing welding of aluminium castings,which was prepared by ISO/TC 44 Welding and allied processes of the International Organization for Stand-ardization, has been adopted by Technical Committee C

19、EN/TC 121 Welding, the Secretariat of which is held by DIN, as a European Standard.This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, and conicting national standards withdrawn, by January2006 at the latest.This docu

20、ment has been prepared under a mandate given to CEN by the European Commission and the Euro-pean Free Trade Association, and supports essential requirements of EU Directive(s).For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document.In accordance wi

21、th the CEN/CENELEC Internal Regulations, the national standards organizations of the follow-ing countries are bound to implement this European Standard:Austria, Belgium, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuani

22、a, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland, and the United Kingdom.Endorsement noticeThe text of the International Standard ISO 15614-4:2005 was approved by CEN as a European Standard with-out any modication.Annex ZA (informative)

23、Relationship between this European Standard and the Essential Requirements of EU Directive 97/23 EEC 17Page 3EN ISO 15614-4:2005Page 4EN ISO 15614-4:2005Page 5EN ISO 15614-4:2005Page 6EN ISO 15614-4:2005Page 7EN ISO 15614-4:2005Page 8EN ISO 15614-4:2005Page 9EN ISO 15614-4:2005Page 10EN ISO 15614-4:2005Page 11EN ISO 15614-4:2005Page 12EN ISO 15614-4:2005Page 13EN ISO 15614-4:2005Page 14EN ISO 15614-4:2005Page 15EN ISO 15614-4:2005Page 16EN ISO 15614-4:2005Page 17EN ISO 15614-4:2005Page 18EN ISO 15614-4:2005