DIN 6791-2012 Semi-tubular pan head rivets - Nominal diameters 1 6 mm to 10 mm《盘头半空心铆钉 公差直径1 6 mm至10 mm》.pdf
《DIN 6791-2012 Semi-tubular pan head rivets - Nominal diameters 1 6 mm to 10 mm《盘头半空心铆钉 公差直径1 6 mm至10 mm》.pdf》由会员分享,可在线阅读,更多相关《DIN 6791-2012 Semi-tubular pan head rivets - Nominal diameters 1 6 mm to 10 mm《盘头半空心铆钉 公差直径1 6 mm至10 mm》.pdf(12页珍藏版)》请在麦多课文档分享上搜索。
1、 May 2012 Translation by DIN-Sprachendienst.English price group 8No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 21
2、.060.40!$|S“1895848www.din.deDDIN 6791Semi-tubular pan head rivets Nominal diameters 1,6 mm to 10 mmEnglish translation of DIN 6791:2012-05Halbhohlniete mit Flachrundkopf Nenndurchmesser 1,6 mm bis 10 mmEnglische bersetzung von DIN 6791:2012-05Rivets semi-tubulaires tte bombe Diamtres nominaux de 1,
3、6 mm 10 mmTraduction anglaise de DIN 6791:2012-05SupersedesDIN 6791:2011-03www.beuth.deIn case of doubt, the German-language original shall be considered authoritative.Document comprises 12 pages05.12 DIN 6791:2012-05 2 A comma is used as the decimal marker. Contents Page Foreword . 3 1 Scope . 4 2
4、Normative references . 4 3 Dimensions 4 4 Technical delivery conditions . 9 5 Designation . 9 6 Application 10 Bibliography . 12 DIN 6791:2012-05 3 Foreword This standard has been prepared by Working Committee NA 067-00-09 AA Verbindungselemente ohne Gewinde of the Normenausschuss Mechanische Verbin
5、dungselemente (Fasteners Standards Committee). Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. DIN shall not be held responsible for identifying any or all such patent rights. The DIN 4000-163 tabular layout of product properties
6、shall apply to rivets covered in this standard. Amendments This standard differs from DIN 6791:1993-05 as follows: a) normative references have been updated; b) Table 4 has been revised; c) equations for calculating head and shank masses have been included; d) the designation has been changed. Compa
7、red with DIN 6791:2011-03 the following corrections have been made: a) in Table 3, the values of deduction in mass per mm bore have been corrected. Previous editions DIN 6791: 1977-07, 1993-05, 2011-03 DIN 6791:2012-05 4 1 Scope This standard specifies dimensions, masses and technical delivery condi
8、tions for semi-tubular pan head rivets with nominal diameters from 1,6 mm to 10 mm. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of th
9、e referenced document (including any amendments) applies. DIN 101, Rivets Technical specifications DIN 4000-163, Tabular layout of product properties Part 163: Fasteners without thread DIN EN 1301-2, Aluminium and aluminium alloys Drawn wire Part 2: Mechanical properties DIN EN 10263-2, Steel rod, b
10、ars and wire for cold heading and cold extrusion Part 2: Technical delivery conditions for steels not intended for heat treatment after cold working DIN EN 10263-5, Steel rod, bars and wire for cold heading and cold extrusion Part 5: Technical delivery conditions for stainless steels DIN EN 12166, C
11、opper and copper alloys Wire for general purposes DIN EN ISO 4042, Fasteners Electroplated coatings 3 Dimensions See Figure 1 and Table 1. Figure 1 Dimensions of semi-tubular pan head rivet (nominal diameters from 1,6 mm to 10 mm) (notation) DIN 6791:2012-05 5 Table 1 Dimensions and masses Dimension
12、s in millimetres d1Nominal size 1,6 2 2,5 3 (3,5) 4 5 6 8 10 Limit deviations 0,05 0,1 0,15 0,2 d2Nominal size 3,2 4 5 6 7 8 10 12 16 20 Limit deviations h14 h15 h16 d3min. 1,52 1,87 2,37 2,87 3,37 3,87 4,82 5,82 6,82 9,40 d4H13 0,9 1,2 1,7 1,9 2,2 2,7 3,5 4,2 6,0 7,6 e max. 0,80 1,00 1,25 1,50 1,75
13、 2,00 2,50 3,00 4,00 5,00 f 0,4 0,5 0,6 0,8 0,9 1,0 1,3 1,5 2,0 2,5 k js14 0,7 0,9 1,1 1,3 1,5 1,8 2,2 2,6 3,5 4,4 r max. 0,2 0,3 0,4 0,5 r1 1,4 1,8 2,2 2,6 3,0 3,5 4,4 5,2 7,0 8,8 t +0,5 0 1,5 2,5 2,5 3,0 4,0 4,0 5,0 6,5 8,0 10,0 l Mass (7,85 kg/dm3) kg/1 000 units a Nominal size Limit deviations 3
14、 +0,25 0 0,068 0,108 0,179 4 +0,30 0 0,084 0,132 0,217 0,339 5 0,100 0,157 0,256 0,395 0,550 0,766 6 0,115 0,181 0,294 0,450 0,626 0,865 1,41 8 +0,36 0 0,147 0,231 0,371 0,561 0,777 1,06 1,72 2,55 10 0,179 0,280 0,448 0,672 0,928 1,26 2,03 2,99 5,69 12 +0,43 0 0,210 0,329 0,525 0,783 1,08 1,46 2,33
15、3,44 6,48 10,78 14 0,242 0,378 0,602 0,894 1,23 1,65 2,64 3,88 7,27 12,02 16 0,273 0,427 0,679 1,01 1,38 1,85 2,95 4,32 8,05 13,26 20 +0,52 0 0,337 0,526 0,833 1,23 1,68 2,25 3,57 5,21 9,63 15,7 25 0,416 0,649 1,03 1,50 2,06 2,74 4,34 6,32 11,60 18,8 30 0,495 0,772 1,22 1,78 2,44 3,23 5,11 7,43 13,6
16、 21,9 35 +0,62 0 0,574 0,895 1,41 2,06 2,82 3,72 5,88 8,54 15,5 25,0 40 0,653 1,018 1,60 2,34 3,19 4,22 6,65 9,65 17,5 28,1 45 0,732 1,141 1,80 2,61 3,57 4,71 7,42 10,8 19,5 31,2 50 0,811 1,264 1,99 2,89 3,95 5,20 8,19 11,9 21,4 34,3 Bracketed sizes and intermediate lengths should be avoided if poss
17、ible. The values of mass specified are for guidance only. See Table 2 for a.DIN 6791:2012-05 6 Table 2 Conversion factors for values of mass Material St, stainless steel Cu CuZn Al Conversion factor 1,000 1,134 1,070 0,344 Table 3 Shank and head masses (steel) Nominal size d11,6 2 2,5 3 (3,5) 4 5 6
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- DIN67912012SEMITUBULARPANHEADRIVETSNOMINALDIAMETERS16MMTO10MM 盘头 半空 铆钉 公差 直径 16 MM 10 MMPDF

链接地址:http://www.mydoc123.com/p-661118.html